Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for Automatic Transaxle)
RM19V0EQ _53 Suspension _014588 FRONT SUSPENSION _0074020 FRONT LOWER SUSPENSION ARM(for Automatic Transaxle) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for Automatic Transaxle)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE FRONT WHEELS

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55702A 5.REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55702A 6.REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 7.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 8.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 9.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 53852K 10.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)

Hide 53851Z 11.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)

Hide 51442C 12.REMOVE ENGINE UNDER COVER LH

Hide 51441C 13.REMOVE ENGINE UNDER COVER RH

Hide 53737B 14.REMOVE FRONT FENDER APRON SEAL LH (for LH Side)

Hide 53736 15.REMOVE FRONT FENDER APRON SEAL RH (for RH Side)

Hide 12361A 16.SEPARATE FRONT ENGINE MOUNTING INSULATOR

a.
C224294

Remove the 3 nuts to separate the front engine mounting insulator from the front frame assembly.


Hide 12372A 17.REMOVE ENGINE MOUNTING INSULATOR LH (for LH Side)

a.
C247247

Remove the 2 hole plugs.


b.
C224295

Remove the 4 nuts from the engine mounting insulator LH.


c.
C224296C03
2.583,1.802 2.76,1.927 2.76,1.927 2.948,1.927 false 2.448,1.083 1.656,1.604 1.656,1.604 1.479,1.604 false 2.958,1.844 3.125,1.99 0.167,0.146 10 *1 1.344,1.521 1.51,1.667 0.167,0.146 10 *2
*1 Jack
*2 Wooden Block


Using a jack and a wooden block, support the engine assembly with transaxle at the position shown in the illustration. While ensuring that there is no interference from the components surrounding the engine, tilt the engine assembly with transaxle to a position that allows the engine mounting insulator LH to be removed.

NOTICE:
·

Do not position the wooden block on the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Tilt the engine assembly with transaxle as little as possible.

·

Ensure that the jack and wooden block are stable.

·

Keep the engine assembly with transaxle supported until installation of the engine mounting insulator LH is complete.




d.
C224297

Remove the engine mounting insulator LH from the front frame assembly.


Hide 48069 18.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for LH Side)

a.
C246185

Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly LH from the front lower ball joint assembly.


b.
C167143

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.

NOTICE:

When removing the bolt, keep the nut from rotating.



c.

Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly LH.


Hide 82284 19.SEPARATE EARTH WIRE (for RH Side)

Hide 12327A 20.REMOVE NO. 2 ENGINE MOUNTING STAY RH (for RH Side)

Hide 12309 21.REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY (for RH Side)

Hide 12362A 22.REMOVE ENGINE MOUNTING INSULATOR RH (for RH Side)

a.
C247246

Remove the 2 hole plugs.


b.
C247235

Remove the 4 nuts from the engine mounting insulator RH.


c.
C224300C02
2.146,1.031 2.656,1.031 2.656,1.031 2.656,1.594 false 1.094,1.552 1.26,1.552 false 2.573,1.604 2.729,1.75 0.156,0.146 10 false *2 0.938,1.479 1.115,1.646 0.177,0.167 10 true *1
*1 Jack
*2 Wooden Block


Using a jack and a wooden block, support the engine assembly with transaxle at the position shown in the illustration. While ensuring that there is no interference from the components surrounding the engine, tilt the engine assembly with transaxle to a position that allows the engine mounting insulator RH to be removed.

NOTICE:
·

Do not position the wooden block on the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Tilt the engine assembly with transaxle as little as possible.

·

Ensure that the jack and wooden block are stable.

·

Keep the engine assembly with transaxle supported until installation of the engine mounting insulator RH is complete.




d.
C247222

Remove the engine mounting insulator RH from the front frame assembly.


Hide 48068 23.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for RH Side)

a.
C247217

Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly RH from the front lower ball joint assembly.


b.
C239314

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly RH from the front frame assembly.

NOTICE:

When removing the bolt, keep the nut from rotating.



c.

Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly RH.