Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY › 2011.10–2015.04
RM19V0EQ _54 Brake _014595 PARKING BRAKE _0074059 PARKING BRAKE ASSEMBLY A

PARKING BRAKE  PARKING BRAKE ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and the LH side.

·

The procedures listed below are for the LH side.

·

Refer to the illustration to confirm the type of brake used.

C249686C02
6.104,2.396 6.302,2.396 false 2.531,2.396 2.74,2.396 false 0.198,0.063 0.708,0.344 0.51,0.281 10 false *A 3.76,0.052 4.219,0.375 0.458,0.323 10 false *B 6.344,2.313 6.719,2.521 0.375,0.208 10 false *1 2.76,2.323 3.396,2.604 0.635,0.281 10 false *1 5.771,1.354 6.365,1.688 0.594,0.333 10 false *b 2.135,1.354 2.719,1.677 0.583,0.323 10 false *a
*A for PBR Made *B for ADVICS Made
*1 Rear Disc - -
*a 190 to 191 mm (7.48 to 7.51 in.) *b 170 to 171 mm (6.69 to 6.73 in.)




PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Hide 42491 3.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 42431 4.REMOVE REAR DISC

Hide 5.REMOVE PARKING BRAKE SHOE ASSEMBLY

a.

for PBR Made:

i.
C240915

Remove the parking brake shoe assembly as shown in the illustration.



Hide 46550G 6.REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Upper Side)

a.

for ADVICS Made Rear Side:

i.
C239422

Remove the parking brake shoe return tension spring.



b.

for ADVICS Made Front Side:

i.
C239423

Remove the parking brake shoe return tension spring.



Hide 47614 7.REMOVE PARKING BRAKE SHOE STRUT

a.

for ADVICS Made:

i.
C239424

Pull the No. 1 parking brake shoe assembly towards the front of the vehicle by hand as shown in the illustration.


ii.
C239425

Remove the parking brake shoe strut.



Hide 47613D 8.REMOVE PARKING BRAKE SHOE STRUT COMPRESSION SPRING

a.

for ADVICS Made:

i.
C240876

Remove the parking brake shoe strut compression spring.



Hide 46580 9.SEPARATE NO. 1 PARKING BRAKE SHOE ASSEMBLY

a.

for ADVICS Made:

i.
C264479

Release the claw of the parking brake shoe hold down spring cup and separate the No. 1 parking brake shoe assembly.



Hide 46590 10.SEPARATE NO. 2 PARKING BRAKE SHOE ASSEMBLY

a.

for ADVICS Made:

i.
C264480

Release the claw of the parking brake shoe hold down spring cup and separate the No. 2 parking brake shoe assembly.



Hide 47406A 11.REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET

a.

for ADVICS Made:

i.
C239428

Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and pull downward to separate them from the parking brake plate.


ii.
C239429

Remove the parking brake shoe adjusting screw set.



Hide 46580 12.REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY

a.

for ADVICS Made:

i.
C239430

Remove the No. 1 parking brake shoe assembly.



Hide 46550E 13.REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)

a.

for ADVICS Made:

i.
C239431

Remove the parking brake shoe return tension spring.



Hide 47612 14.SEPARATE PARKING BRAKE SHOE LEVER

a.

for ADVICS Made:

i.
C239432

Using needle-nose pliers, separate the parking brake shoe lever from the No. 3 parking brake cable assembly.



Hide 47612 15.REMOVE PARKING BRAKE SHOE LEVER

a.

for ADVICS Made:

i.
C239433

Using a screwdriver, remove the parking brake shoe type C washer, parking brake shoe shim and the parking brake shoe lever.

HINT:

Parking brake shoe shims are provided when necessary to adjust the clearance between the parking brake shoe lever and parking brake shoe type C washer. Some vehicles may not be equipped with shims.




Hide 47447E 16.REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING PIN

a.

for ADVICS Made Front Side:

i.
C240101

Remove the 2 parking brake shoe hold down spring cups, parking brake shoe hold down spring and parking brake shoe hold down spring pin.



b.

for ADVICS Made Rear Side:

i.
C240102

Remove the 2 parking brake shoe hold down spring cups, parking brake shoe hold down spring and parking brake shoe hold down spring pin.



Hide 47456A 17.REMOVE PARKING BRAKE SHOE GUIDE PLATE

a.

for ADVICS Made:

i.
C240103

Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.



Hide 46430 18.DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 19.REMOVE NUT AND SCREW ADJUSTING ASSEMBLY

a.

for PBR Made:

i.
C240917

Remove the nut and screw adjusting assembly, parking brake tappet and parking brake push rod.



Hide 20.REMOVE ADJUSTMENT PAWL

a.

for PBR Made:

i.
C240918

Remove the adjustment pawl.



Hide 21.REMOVE PARKING BRAKE SHOE HOLD PLATE

a.

for PBR Made:

i.
C240919

Remove the parking brake shoe hold bolt and the parking brake shoe hold plate.



Hide 89516D 22.DISCONNECT SKID CONTROL SENSOR WIRE

Hide 42450B 23.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

Hide 24.SEPARATE DUST PLATE

a.

for PBR Made:

i.

Separate the dust plate from the parking brake plate sub-assembly.



Hide 25.REMOVE PARKING BRAKE PLATE SUB-ASSEMBLY

a.

for PBR Made:

i.

Remove the parking brake plate sub-assembly.



Hide 26.REMOVE DUST COVER

a.

for PBR Made:

i.
C240920N01
2.948,0.219 3.281,0.427 0.333,0.208 10 false (A)

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Tape the 4 mm (0.157 in.) drill bit with the portion of 5 mm (0.197 in.) from the tip uncovered.

Dimension (A):

5 mm (0.197 in.)


HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



iii.

Lightly press the drill against the rivets, drill off the flanges of the rivets, and remove the 2 rivets.

NOTICE:
·

Cover the dust cover with a piece of cloth to prevent rivet fragments and shavings from scattering.

·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill out the rivet head.

·

Be careful as the cut rivet will be very hot.




iv.

Remove the boot retainer and the dust cover.


v.

Even if the flange is taken off, continue to drill the rivet and push out the remaining fragment using a drill.


vi.

Using a vacuum cleaner, remove the rivet fragments and shavings.



Hide 27.REMOVE PARKING BRAKE SHOE LEVER

a.

for PBR Made:

i.

Remove the parking brake shoe lever.