Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM19V0EQ _55 Steering _014596 POWER ASSIST SYSTEMS _0074061 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1524/24  Motor Circuit Malfunction  C1555/25  Motor Relay Welding Failure  


DESCRIPTION

The power steering ECU assembly supplies current to the power steering motor assembly through the motor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1524/24 Motor Circuit Malfunction Short (or open) in motor circuit or abnormal voltage or current in motor circuit
·

Power steering motor assembly

·

Power steering ECU assembly


EPS Warning Light: Comes on Ignition switch ON again
C1555/25 Motor Relay Welding Failure Motor relay circuit malfunction
·

Power steering motor assembly

·

Power steering ECU assembly


EPS Warning Light: Comes on Ignition switch ON again

WIRING DIAGRAM

C246148E04
4.552,2.573 4.823,2.74 0.271,0.167 10 false c 4.552,2.75 6.625,3 2.073,0.25 10 false Power Steering ECU Assembly 0.115,2.5 2.219,2.771 2.104,0.271 10 false Power Steering Motor Assembly 4.729,0.74 5.177,1.031 0.448,0.292 10 false PHA 4.729,1.323 5.365,1.542 0.635,0.219 10 false PHB 4.729,1.927 5.208,2.156 0.479,0.229 10 false PHC 4.469,0.604 4.656,0.854 0.188,0.25 10 false 1 4.479,1.177 4.708,1.406 0.229,0.229 10 false 2 4.458,1.792 4.646,2.021 0.188,0.229 10 false 3

INSPECTION PROCEDURE

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.INSPECT TIGHTENING TORQUE OF MOTOR TERMINAL BOLT
a.

Disengage the 4 claws to remove the protector.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING ECU>REMOVAL


b.

Check that the motor terminal bolts are tightened to the specified torque.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING ECU>INSTALLATION

OK:

The motor terminal bolts are tightened to the specified torque.



Result:
Proceed to
OK
NG



OK

2.INSPECT POWER STEERING MOTOR ASSEMBLY

NG

TIGHTEN BOLT TO SPECIFIED TORQUE

2.INSPECT POWER STEERING MOTOR ASSEMBLY
a.
C240264C03
0.188,1.083 0.635,1.365 0.448,0.281 1.74,1.969 1.74,1.885 false 2.052,1.813 2.26,1.865 false 1.396,1.813 1.188,1.865 false 0.125,0.063 0.385,0.271 0.26,0.208 10 false *1 1.438,1.969 2.073,2.146 0.635,0.177 10 false 1 (PHA) 2.292,1.802 2.844,2.042 0.552,0.24 10 false 2 (PHB) 0.698,1.802 1.25,2.083 0.552,0.281 10 false 3 (PHC) 0.375,1.146 0.771,1.427 0.396,0.281 10 false c
*1 Power Steering Motor Assembly


Remove the power steering motor assembly.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c-1 (PHA) - c-2 (PHB) 25°C (77°F) 12.7 to 17.2 mΩ
c-2 (PHB) - c-3 (PHC) 25°C (77°F) 12.7 to 17.2 mΩ
c-3 (PHC) - c-1 (PHA) 25°C (77°F) 12.7 to 17.2 mΩ
c-1 (PHA) - Motor case Always 10 kΩ or higher
c-2 (PHB) - Motor case Always 10 kΩ or higher
c-3 (PHC) - Motor case Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (MOTOR VOLTAGE)

NG

REPLACE POWER STEERING MOTOR ASSEMBLY

3.READ VALUE USING INTELLIGENT TESTER (MOTOR VOLTAGE)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the items "Motor Terminal Volt (U)", "Motor Terminal Volt (V)" and "Motor Terminal Volt (W)" in the Data List and read the value displayed on the intelligent tester.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Motor Terminal Volt(U) Motor terminal voltage (A phase) Min.: 0.000 V
Max.: 98.000 V
Engine running and steering wheel being turned: Value changes within 4 to 35 V range -
Motor Terminal Volt(V) Motor terminal voltage (B phase) Min.: 0.000 V
Max.: 98.000 V
Engine running and steering wheel being turned: Value changes within 4 to 35 V range -
Motor Terminal Volt(W) Motor terminal voltage (C phase) Min.: 0.000 V
Max.: 98.000 V
Engine running and steering wheel being turned: Value changes within 4 to 35 V range -
Chassis > EMPS > Data List
Tester Display
Motor Terminal Volt(U)
Motor Terminal Volt(V)
Motor Terminal Volt(W)
50003 142 22,23,24

Result:
Result Proceed to
During steering operation, value changes within 4 to 35 V range. A
During steering operation, voltage is not generated. B



A

REPLACE POWER STEERING ECU ASSEMBLY

B

REPLACE POWER STEERING MOTOR ASSEMBLY