Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014600 NAVIGATION / MULTI INFO DISPLAY _0074086 NAVIGATION SYSTEM(for HDD) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  B15C3  Speaker Output Short  


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C3 Speaker Output Short A short is detected in the speaker output circuit.
·

Harness or connector

·

Speaker

·

Stereo component amplifier assembly*1

·

Navigation ECU sub-assembly*2



*1: for 10 Speakers

*2: for 6 Speakers


WIRING DIAGRAM

for 6 Speakers


E226481E28
5.792,7.448 6.781,7.802 0.99,0.354 10 false Navigation ECU Sub-assembly 3.021,1.188 4.302,1.844 1.281,0.656 10 false Front No. 2 Speaker Assembly RH 5.563,0.771 5.667,0.927 0.104,0.156 10 false 1 4.531,0.813 4.635,0.969 0.104,0.156 10 false 4 4.531,1.677 4.635,1.833 0.104,0.156 10 false 2 2.333,0.844 2.438,1 0.104,0.156 10 false 3 2.333,1.729 2.438,1.885 0.104,0.156 10 false 1 2.469,0.844 2.573,1 0.104,0.156 10 false + 2.469,1.708 2.573,1.865 0.104,0.156 10 false - 4.063,1.677 4.5,1.833 0.438,0.156 10 false TWR- 4.063,2.792 4.5,2.948 0.438,0.156 10 false TWL+ 4.063,3.656 4.5,3.813 0.438,0.156 10 false TWL- 4.063,0.813 4.5,0.969 0.438,0.156 10 false TWR+ 5.51,0.948 5.802,1.135 0.292,0.188 10 false I64 5.51,1.823 5.802,2.01 0.292,0.188 10 false I64 3.021,1.052 3.281,1.208 0.26,0.156 10 false I83 0.344,1.26 1.625,1.917 1.281,0.656 10 false Front No. 1 Speaker Assembly RH 0.344,1.104 0.604,1.26 0.26,0.156 10 false J5 3.021,3.167 4.302,3.823 1.281,0.656 10 false Front No. 2 Speaker Assembly LH 4.531,2.792 4.635,2.948 0.104,0.156 10 false 4 4.531,3.656 4.635,3.813 0.104,0.156 10 false 2 2.333,2.823 2.438,2.979 0.104,0.156 10 false 3 2.333,3.698 2.438,3.854 0.104,0.156 10 false 1 2.469,2.823 2.573,2.979 0.104,0.156 10 false + 2.469,3.688 2.573,3.844 0.104,0.156 10 false - 3.021,3.031 3.281,3.188 0.26,0.156 10 false I1 0.344,3.24 1.625,3.896 1.281,0.656 10 false Front No. 1 Speaker Assembly LH 0.344,3.083 0.604,3.24 0.26,0.156 10 false K5 0.74,5.063 1.646,5.719 0.906,0.656 10 false Rear Speaker Assembly RH 0.74,4.896 1.052,5.052 0.313,0.156 10 false O18 0.74,6.583 1.646,7.24 0.906,0.656 10 false Rear Speaker Assembly LH 0.74,6.427 1.031,6.583 0.292,0.156 10 false O21 5.844,0.948 6.281,1.208 0.438,0.26 10 false FR+ 5.844,1.813 6.167,2.052 0.323,0.24 10 false FR- 5.844,2.927 6.333,3.208 0.49,0.281 10 false FL+ 5.844,3.792 6.25,4.063 0.406,0.271 10 false FL- 5.844,4.844 6.26,5.073 0.417,0.229 10 false RR+ 5.844,5.458 6.271,5.771 0.427,0.313 10 false RR- 5.844,6.365 6.313,6.625 0.469,0.26 10 false RL+ 5.844,7 6.229,7.208 0.385,0.208 10 false RL- 5.563,6.813 5.667,6.969 0.104,0.156 10 false 6 5.563,6.188 5.667,6.344 0.104,0.156 10 false 2 5.563,5.302 5.667,5.458 0.104,0.156 10 false 3 5.563,4.667 5.667,4.823 0.104,0.156 10 false 1 5.563,3.594 5.667,3.75 0.104,0.156 10 false 6 5.563,2.729 5.667,2.885 0.104,0.156 10 false 2 5.563,1.625 5.667,1.781 0.104,0.156 10 false 5 1.792,1.094 1.896,1.25 0.104,0.156 10 false 1 1.792,1.698 2,1.979 0.208,0.281 10 false 2 1.792,3.073 1.896,3.229 0.104,0.156 10 false 1 1.792,3.677 1.896,3.833 0.104,0.156 10 false 2 1.792,4.854 1.896,5.01 0.104,0.156 10 false 1 1.792,5.479 1.896,5.635 0.104,0.156 10 false 2 1.792,6.354 1.896,6.51 0.104,0.156 10 false 1 1.792,7 1.896,7.156 0.104,0.156 10 false 2 5.51,2.927 5.802,3.115 0.292,0.188 10 false I64 5.51,3.802 5.802,3.99 0.292,0.188 10 false I64 5.51,4.844 5.802,5.031 0.292,0.188 10 false I65 5.51,5.479 5.802,5.667 0.292,0.188 10 false I65 5.51,7 5.958,7.292 0.448,0.292 10 false I65 5.51,6.365 5.969,6.646 0.458,0.281 10 false I65


for 10 Speakers


E226522E12
5.729,0.635 5.917,0.792 0.188,0.156 10 false 15 6,0.75 6.417,1 0.417,0.25 10 false FR+ 6,1.375 6.417,1.583 0.417,0.208 10 false FR- 5.99,1.844 6.333,2.167 0.344,0.323 10 false FL+ 5.99,2.5 6.25,2.656 0.26,0.156 10 false FL- 6,3.094 6.427,3.25 0.427,0.156 10 false TWR+ 6,3.729 6.396,3.885 0.396,0.156 10 false TWR- 6,4.344 6.406,4.5 0.406,0.156 10 false TWL+ 6,5.01 6.375,5.167 0.375,0.156 10 false TWL- 5.719,4.885 5.896,5.042 0.177,0.156 10 false 29 5.833,5.76 6.094,5.917 0.26,0.156 10 false I68 5.708,4.24 5.885,4.396 0.177,0.156 10 false 14 5.729,3.615 5.99,3.854 0.26,0.24 10 false 27 5.719,2.979 6.052,3.302 0.333,0.323 10 false 12 5.729,2.375 5.906,2.531 0.177,0.156 10 false 26 5.729,1.719 5.917,1.875 0.188,0.156 10 false 11 5.719,1.25 5.896,1.406 0.177,0.156 10 false 30 5.833,5.927 7.052,6.583 1.219,0.656 10 false Stereo Component Amplifier Assembly 1.917,0.75 2.021,0.906 0.104,0.156 10 false 1 1.917,1.365 2.021,1.521 0.104,0.156 10 false 2 1.917,1.854 2.021,2.01 0.104,0.156 10 false 1 1.917,2.479 2.021,2.635 0.104,0.156 10 false 2 2.917,3 3.021,3.156 0.104,0.156 10 false 4 2.917,3.594 3.021,3.75 0.104,0.156 10 false 3 2.917,4.25 3.021,4.406 0.104,0.156 10 false 4 2.917,4.885 3.021,5.042 0.104,0.156 10 false 3 0.417,0.917 1.698,1.573 1.281,0.656 10 false Front No. 1 Speaker Assembly RH 0.417,0.75 0.677,0.906 0.26,0.156 10 false J5 0.417,2.167 1.698,2.823 1.281,0.656 10 false Front No. 1 Speaker Assembly LH 0.417,2.01 0.677,2.167 0.26,0.156 10 false K5 0.333,3.344 1.615,4 1.281,0.656 10 false Front No. 2 Speaker Assembly RH 0.333,3.167 0.594,3.323 0.26,0.156 10 false I84 0.333,4.594 1.615,5.25 1.281,0.656 10 false Front No. 2 Speaker Assembly LH 0.323,4.427 0.583,4.583 0.26,0.156 10 false I2

E226483E19
5.969,0.74 6.365,0.896 0.396,0.156 10 false CTR+ 5.969,1.365 6.344,1.521 0.375,0.156 10 false CTR- 5.698,1.26 5.875,1.417 0.177,0.156 10 false 28 5.688,0.625 5.875,0.781 0.188,0.156 10 false 13 1.917,0.719 2.021,0.875 0.104,0.156 10 false 2 1.917,1.365 2.021,1.521 0.104,0.156 10 false 1 0.5,1 1.781,1.656 1.281,0.656 10 false Front No. 3 Speaker Assembly 0.49,0.844 0.75,1 0.26,0.156 10 false I60 5.979,1.844 6.281,2 0.302,0.156 10 false SR+ 5.979,2.479 6.24,2.635 0.26,0.156 10 false SR- 5.708,2.365 5.885,2.521 0.177,0.156 10 false 25 5.698,1.74 5.885,1.896 0.188,0.156 10 false 10 1.917,1.833 2.021,1.99 0.104,0.156 10 false 2 1.917,2.5 2.021,2.656 0.104,0.156 10 false 1 0.5,2.083 1.813,2.438 1.313,0.354 10 false Rear No. 2 Speaker Assembly RH 0.5,1.917 0.844,2.073 0.344,0.156 10 false O19 5.979,2.958 6.281,3.115 0.302,0.156 10 false SL+ 5.979,3.583 6.24,3.74 0.26,0.156 10 false SL- 5.719,3.479 5.896,3.635 0.177,0.156 10 false 24 5.75,2.854 5.938,3.01 0.188,0.156 10 false 9 1.917,2.948 2.021,3.104 0.104,0.156 10 false 2 1.917,3.604 2.021,3.76 0.104,0.156 10 false 1 0.5,3.333 1.813,3.708 1.313,0.375 10 false Rear No. 2 Speaker Assembly LH 0.5,3.167 0.833,3.323 0.333,0.156 10 false O20 5.99,4.063 6.396,4.219 0.406,0.156 10 false WF1+ 5.99,4.698 6.375,4.854 0.385,0.156 10 false WF1- 5.708,4.594 5.885,4.75 0.177,0.156 10 false 23 5.75,3.958 5.938,4.115 0.188,0.156 10 false 8 1.917,4.083 2.021,4.24 0.104,0.156 10 false 1 1.917,4.719 2.021,4.875 0.104,0.156 10 false 2 0.333,4.417 1.906,4.625 1.573,0.208 10 false Rear Speaker Assembly 0.333,4.25 0.615,4.406 0.281,0.156 10 false O22 5.906,5.25 6.167,5.406 0.26,0.156 10 false I68 5.917,5.427 7.135,6.083 1.219,0.656 10 false Stereo Component Amplifier Assembly


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Model Proceed to
for 6 Speakers A
for 10 Speakers B




A

2.CHECK HARNESS AND CONNECTOR

B

7.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the connectors from the navigation ECU sub-assembly and speakers.


b.

Measure the resistance between the navigation ECU sub-assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I64-1 (FR+) - Body ground Always 10 kΩ or higher
I64-5 (FR-) - Body ground Always 10 kΩ or higher
I64-2 (FL+) - Body ground Always 10 kΩ or higher
I64-6 (FL-) - Body ground Always 10 kΩ or higher
I65-1 (RR+) - Body ground Always 10 kΩ or higher
I65-3 (RR-) - Body ground Always 10 kΩ or higher
I65-2 (RL+) - Body ground Always 10 kΩ or higher
I65-6 (RL-) - Body ground Always 10 kΩ or higher



c.

Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I83-3 (+) - Body ground Always 10 kΩ or higher
I83-1 (-) - Body ground Always 10 kΩ or higher
I1-3 (+) - Body ground Always 10 kΩ or higher
I1-1 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.
E219303C56
0.51,1.906 1.042,2.198 0.531,0.292 0.51,1.531 1.042,1.823 0.531,0.292 0.708,1.958 1.208,2.208 0.5,0.25 10 false K5 1.104,1.958 1.479,2.208 0.375,0.25 10 false *B 0.708,1.583 1.146,1.844 0.438,0.26 10 false J5 1.083,1.594 1.469,1.917 0.385,0.323 10 false *A 0.135,0.146 0.573,0.542 0.438,0.396 10 false *a
*A for RH
*B for LH
*a Component without harness connected
(Front No. 1 Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-1 - J5-2 Always 3.2 to 4.8 Ω
K5-1 - K5-2 Always 3.2 to 4.8 Ω




Result:
Proceed to
OK
NG



OK

4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.
E226097C25
1.469,0.656 1.927,0.938 0.458,0.281 1.458,1 1.917,1.281 0.458,0.281 1.333,1.802 1.083,2.469 false 1.677,1.813 1.563,2.229 false 2.302,1.813 2.417,2.229 false 1.99,1.802 2.167,2.469 false 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 1.958,0.729 2.208,0.906 0.25,0.177 10 false *A 1.958,1.063 2.208,1.24 0.25,0.177 10 false *B 1.573,0.719 1.823,0.885 0.25,0.167 10 false I83 1.625,1.063 1.948,1.333 0.323,0.271 10 false I1 1.5,2.24 1.656,2.385 0.156,0.146 10 false + 0.656,2.51 1.302,2.656 0.646,0.146 10 false TWR+*A 0.656,2.688 1.26,2.833 0.604,0.146 10 false TWL+*B 1.844,2.51 2.615,2.76 0.771,0.25 10 false TWR-*A 1.844,2.688 2.542,2.927 0.698,0.24 10 false TWL-*B 2.417,2.208 2.531,2.354 0.115,0.146 10 false -
*A for RH
*B for LH
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I83-2 (TWR-) - I83-4 (TWR+) Always 10 kΩ or higher
I83-1 (-) - I83-2 (TWR-) Always Below 1 Ω
I83-3 (+) - I83-4 (TWR+) Always Below 1 Ω
I1-2 (TWL-) - I1-4 (TWL+) Always 10 kΩ or higher
I1-1 (-) - I1-2 (TWL-) Always Below 1 Ω
I1-3 (+) - I1-4 (TWL+) Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

5.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

5.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Check that the malfunction disappears when a known good speaker is installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both LH and RH sides.




Result:
Proceed to
OK
NG



OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

NG

6.INSPECT REAR SPEAKER ASSEMBLY
6.INSPECT REAR SPEAKER ASSEMBLY
a.
E219303C57
0.469,1.917 1,2.208 0.531,0.292 0.469,1.542 1,1.833 0.531,0.292 0.604,1.979 1.125,2.24 0.521,0.26 10 false O21 0.604,1.604 1.052,1.854 0.448,0.25 10 false O18 0.292,0.219 0.635,0.531 0.344,0.313 10 false *a 1.073,1.594 1.25,1.76 0.177,0.167 10 false *A 1.073,1.979 1.25,2.146 0.177,0.167 10 false *B
*A for RH
*B for LH
*a Component without harness connected
(Rear Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O18-1 - O18-2 Always 3.2 to 4.8 Ω
O21-1 - O21-2 Always 3.2 to 4.8 Ω




Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR
a.

Disconnect the connectors from the stereo component amplifier assembly and speakers.


b.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-15 (FR+) - Body ground Always 10 kΩ or higher
I68-30 (FR-) - Body ground Always 10 kΩ or higher
I68-11 (FL+) - Body ground Always 10 kΩ or higher
I68-26 (FL-) - Body ground Always 10 kΩ or higher
I68-12 (TWR+) - Body ground Always 10 kΩ or higher
I68-27 (TWR-) - Body ground Always 10 kΩ or higher
I68-14 (TWL+) - Body ground Always 10 kΩ or higher
I68-29 (TWL-) - Body ground Always 10 kΩ or higher
I68-13 (CTR+) - Body ground Always 10 kΩ or higher
I68-28 (CTR-) - Body ground Always 10 kΩ or higher
I68-10 (SR+) - Body ground Always 10 kΩ or higher
I68-25 (SR-) - Body ground Always 10 kΩ or higher
I68-9 (SL+) - Body ground Always 10 kΩ or higher
I68-24 (SL-) - Body ground Always 10 kΩ or higher
I68-8 (WF1+) - Body ground Always 10 kΩ or higher
I68-23 (WF1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.
E219303C56
0.51,1.906 1.042,2.198 0.531,0.292 0.51,1.531 1.042,1.823 0.531,0.292 0.708,1.958 1.208,2.208 0.5,0.25 10 false K5 1.104,1.958 1.479,2.208 0.375,0.25 10 false *B 0.708,1.583 1.146,1.844 0.438,0.26 10 false J5 1.083,1.594 1.469,1.917 0.385,0.323 10 false *A 0.135,0.146 0.573,0.542 0.438,0.396 10 false *a
*A for RH
*B for LH
*a Component without harness connected
(Front No. 1 Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-1 - J5-2 Always 4.6 to 6.6 Ω
K5-1 - K5-2 Always 4.6 to 6.6 Ω




Result:
Proceed to
OK
NG



OK

9.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

9.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.
E219304C20
0.125,1.469 0.656,1.76 0.531,0.292 0.125,1.875 0.656,2.167 0.531,0.292 0.313,1.531 0.688,1.76 0.375,0.229 10 false I84 0.688,1.542 1.01,1.833 0.323,0.292 10 false *A 0.125,0.167 0.469,0.479 0.344,0.313 10 false *a 0.354,1.938 0.656,2.188 0.302,0.25 10 false I2 0.688,1.927 1.104,2.208 0.417,0.281 10 false *B
*A for RH
*B for LH
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I84-4 - I84-3 Always 3.4 to 5.2 Ω
I2-4 - I2-3 Always 3.4 to 5.2 Ω




Result:
Proceed to
OK
NG



OK

10.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY

NG

10.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY
a.
E222247C24
0.521,1.385 1.052,1.677 0.531,0.292 0.125,0.177 0.438,0.438 0.313,0.26 10 false *a 0.698,1.458 0.99,1.729 0.292,0.271 10 false I60
*a Component without harness connected
(Front No. 3 Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I60-1 - I60-2 Always 6.8 to 10.2 Ω




Result:
Proceed to
OK
NG



OK

11.INSPECT REAR NO. 2 SPEAKER ASSEMBLY

NG

11.INSPECT REAR NO. 2 SPEAKER ASSEMBLY
a.
E222247C25
0.375,1.385 0.906,1.677 0.531,0.292 0.375,1.74 0.906,2.031 0.531,0.292 0.177,0.188 0.521,0.49 0.344,0.302 10 false *a 0.5,1.448 1.26,1.854 0.76,0.406 10 false O19 0.969,1.458 1.271,1.74 0.302,0.281 10 false *A 0.521,1.813 1.063,2.083 0.542,0.271 10 false O20 0.969,1.813 1.26,2.063 0.292,0.25 10 false *B
*A for RH
*B for LH
*a Component without harness connected
(Rear No. 2 Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O19-1 - O19-2 Always 6.8 to 10.2 Ω
O20-1 - O20-2 Always 6.8 to 10.2 Ω




Result:
Proceed to
OK
NG



OK

12.INSPECT REAR SPEAKER ASSEMBLY

NG

12.INSPECT REAR SPEAKER ASSEMBLY
a.
E219303C58
0.75,1.708 1.177,2.01 0.427,0.302 0.833,1.771 1.271,1.99 0.438,0.219 10 false O22 0.271,0.177 0.583,0.479 0.313,0.302 10 false *a
*a Component without harness connected
(Rear Speaker Assembly)


Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O22-1 - O22-2 Always 4.8 to 6.8 Ω




Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG