Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074120 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment  


DESCRIPTION

If the luggage compartment door entry unlock function does not operate, the request code may not be being transmitted from the luggage compartment door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage)), a luggage compartment door outer switch malfunction or wave interference.

HINT:

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.


WIRING DIAGRAM

B274856E02
2.219,1.344 2.667,1.563 0.448,0.219 10 T11 2.219,1.5 4.854,1.875 2.635,0.375 10 Electrical Key Antenna (Outside Luggage) 4.333,0.469 4.823,0.729 0.49,0.26 10 CLGB 4.802,0.469 5.25,0.813 0.448,0.344 10 2 4.792,0.833 5.094,1.073 0.302,0.24 10 1 5.667,0.365 5.979,0.635 0.313,0.271 10 1 5.958,0.573 6.552,1.063 0.594,0.49 10 CG8B 5.958,0.927 6.563,1.26 0.604,0.333 10 CLG8 5.677,0.74 5.948,1.052 0.271,0.313 10 2 4.344,0.833 4.938,1.208 0.594,0.375 10 CLG5 5.625,0.542 6.052,0.885 0.427,0.344 10 O1 5.625,0.917 6.115,1.188 0.49,0.271 10 O1 5.625,2.219 5.99,2.5 0.365,0.281 10 O1 5.5,3.188 7.031,3.615 1.531,0.427 10 Certification ECU (Smart Key ECU Assembly) 2.323,2.531 2.573,2.677 0.25,0.146 10 T4 2.323,2.688 3.76,3.156 1.438,0.469 10 Luggage Door Opening Switch Assembly 5.969,2.24 6.563,2.594 0.594,0.354 10 TSW5 3.458,2.125 3.771,2.438 0.313,0.313 10 3 2.396,2.125 2.792,2.406 0.396,0.281 10 2 5.635,2.042 5.938,2.333 0.302,0.292 10 27 2.583,2.125 2.917,2.396 0.333,0.271 10 E 3.198,2.125 3.542,2.365 0.344,0.24 10 UL 5.771,6.635 6.927,7.354 1.156,0.719 10 Main Body ECU (Multiplex Network Body ECU) 4.521,6.438 5.583,7.146 1.063,0.708 10 Instrument Panel Junction Block Assembly 1.656,6.573 3.073,7 1.417,0.427 10 Luggage Compartment Door Lock Assembly 5.969,4.896 6.49,5.104 0.521,0.208 10 LGCY 5.688,4.677 5.875,4.844 0.188,0.167 10 4 5.615,4.885 6.063,5.156 0.448,0.271 10 MB 1.344,5.698 1.698,6 0.354,0.302 10 2 2.979,4.781 3.208,4.948 0.229,0.167 10 D+ 1.531,5.698 1.854,6.042 0.323,0.344 10 E 3.25,5.698 3.469,6.01 0.219,0.313 10 1 3.26,4.781 3.406,4.948 0.146,0.167 10 3 4.396,4.688 4.583,4.854 0.188,0.167 10 9 4.344,4.885 4.792,5.219 0.448,0.333 10 3C 5.969,5.833 6.333,6.135 0.365,0.302 10 TR+ 5.677,5.615 5.865,5.781 0.188,0.167 10 6 5.625,5.813 6.063,6.073 0.438,0.26 10 MB 0.823,7.344 2.667,7.552 1.844,0.208 10 : CAN Communication Line 1.906,5.135 2.906,5.521 1,0.385 10 Luggage Door Courtesy Switch 1.875,5.969 3.021,6.188 1.146,0.219 10 Door Lock Motor 3.052,5.698 3.354,6.156 0.302,0.458 10 B 4.344,5.615 4.688,5.917 0.344,0.302 10 10 4.344,5.813 4.917,6.188 0.573,0.375 10 3C 1.656,6.417 2.115,6.729 0.458,0.313 10 T3

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the intelligent tester with the engine switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (LUGGAGE COMPARTMENT DOOR OPEN MODE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Trunk Open Mode Luggage door opening switch assembly ON or OFF Customization status displayed -
Body Electrical > Entry&Start > Data List
Tester Display
Trunk Open Mode
50003 125 3

Result:
Result Proceed to
Entry luggage compartment door open mode is ON A
Entry luggage compartment door open mode is OFF B



A

2.READ VALUE USING INTELLIGENT TESTER (LUGGAGE DOOR OPENING SWITCH ASSEMBLY)

B

2.READ VALUE USING INTELLIGENT TESTER (LUGGAGE DOOR OPENING SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Luggage compartment door opener outer switch ON or OFF ON: Luggage compartment door opener outer switch pushed
OFF: Luggage compartment door opener outer switch not pushed
-
Body Electrical > Entry&Start > Data List
Tester Display
Tr/B-Door Unlock SW
50003 125 17
OK:

On the intelligent tester screen, the display changes between ON and OFF according to the chart above.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

12.INSPECT LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Trunk and Back-Door Open Operate luggage compartment door lock motor ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Trunk and Back-Door Open
50004 123 3
OK:

Luggage compartment door lock motor operates.



Result:
Proceed to
OK
NG



OK

4.CHECK WAVE ENVIRONMENT

NG

8.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
4.CHECK WAVE ENVIRONMENT
a.
B274824C09
1.875,1.322 2.053,1.483 0.178,0.162 10 *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly near the electrical key antenna (outside luggage), and perform an entry luggage compartment open function check.

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication is not possible.


HINT:
·

When pressing the luggage compartment door opener outer switch, hold the electrical key transmitter sub-assembly approximately 1 m (3.28 ft.) above the ground and approximately 0.3 m (0.984 ft.) away from the vehicle as shown in the illustration.

·

When the electrical key transmitter sub-assembly is brought near the electrical key antenna (outside luggage), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



OK:

Entry functions operate normally.



Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

5.CHECK KEY DIAGNOSTIC MODE
5.CHECK KEY DIAGNOSTIC MODE

b.
B274824C09
1.875,1.322 2.053,1.483 0.178,0.162 10 *a
*a 0.7 to 1.0 m (2.30 to 3.28 ft.)


Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.

i.

When the electrical key transmitter sub-assembly is held at the same height as the rear bumper upper surface, align it with the center of the rear of the vehicle and check that the wireless door lock buzzer sounds.

HINT:
·

Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle (0.7 to 1.0 m (2.30 to 3.28 ft.)). Make sure that the direction of the electrical key transmitter sub-assembly is as shown in the illustration.

·

If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless door lock buzzer sounds.




Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ELECTRICAL KEY ANTENNA)
6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ELECTRICAL KEY ANTENNA)
a.

Disconnect the O1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the T11 electrical key antenna (outside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O1-1 (CG8B) - T11-2 (CLGB) Always Below 1 Ω
O1-2 (CLG8) - T11-1 (CLG5) Always Below 1 Ω
O1-1 (CG8B) or T11-2 (CLGB) - Body ground Always 10 kΩ or higher
O1-2 (CLG8) or T11-1 (CLG5) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
a.
B226391C24
1.833,1.104 2.5,1.521 false 1.573,1.104 0.927,1.521 false 2.375,1.552 2.802,1.729 0.427,0.177 10 CLGB 0.646,1.542 1.042,1.719 0.396,0.177 10 CLG5 0.198,0.167 0.615,0.552 0.417,0.385 10 *a
*a Component without harness connected
(Electrical Key Antenna (Outside Luggage))


Remove the electrical key antenna (outside luggage).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (CLG5) - 2 (CLGB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

8.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
a.
B279065C03
2.521,2.208 2.521,2.5 2.521,2.5 2.438,2.5 false 2.677,2.208 2.677,2.5 2.677,2.5 2.76,2.5 false 0.365,0.833 0.521,1 0.156,0.167 10 *b 0.115,0.073 0.271,0.24 0.156,0.167 10 *a 1.76,0.833 1.917,1 0.156,0.167 10 *c 2.323,2.417 2.438,2.563 0.115,0.146 10 E 2.802,2.417 2.917,2.563 0.115,0.146 10 B
*a Component without harness connected
(Luggage Compartment Door Lock Assembly)
*b Close (Lock)
*c Open (Unlock)


Remove the luggage compartment door lock assembly.

Click hereVehicle Interior>DOOR LOCK>LUGGAGE COMPARTMENT DOOR LOCK>REMOVAL


b.

Check the operation of the door lock motor.

i.

Move the door lock to the close (lock) position.


ii.

Apply battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (B)
Battery negative (-) → 2 (E)
Luggage compartment door lock motor open (unlock) operation




c.
B279065C04
2.385,2.208 2.385,2.5 2.385,2.5 2.313,2.5 false 2.531,2.208 2.531,2.5 2.531,2.5 2.604,2.5 false 0.365,0.833 0.521,1 0.156,0.167 10 *b 0.115,0.073 0.271,0.24 0.156,0.167 10 *a 1.76,0.833 1.917,1 0.156,0.167 10 *c 2.646,2.438 2.76,2.583 0.115,0.146 10 E 2.104,2.417 2.302,2.563 0.198,0.146 10 D+
*a Component without harness connected
(Luggage Compartment Door Lock Assembly)
*b Close (Lock)
*c Open (Unlock)


Check the door courtesy light switch.

i.

Move the door lock to the close (lock) position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Measurement Condition Door Lock Condition Specified Condition
2 (E) - 3 (D+) Close (Lock) 10 kΩ or higher
2 (E) - 3 (D+) Open (Unlock) Below 1 Ω




Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR LOCK - INSTRUMENT PANEL JUNCTION BLOCK)

NG

REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR LOCK - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Luggage compartment door lock motor:

i.

Disconnect the 3C instrument panel junction block assembly connector.


ii.

Disconnect the T3 luggage compartment door lock assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-10 (TR+) - T3-1 (B) Always Below 1 Ω
3C-10 (TR+) or T3-1 (B) - Body ground Always 10 kΩ or higher
T3-2 (E) - Body ground Always Below 1 Ω




b.

Luggage door courtesy light switch:

i.

Disconnect the 3C instrument panel junction block assembly connector.


ii.

Disconnect the T3 luggage compartment door lock assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-9 (LGCY) - T3-3 (D+) Always Below 1 Ω
3C-9 (LGCY) or T3-3 (D+) - Body ground Always 10 kΩ or higher
T3-2 (E) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

10.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Temporarily replace the instrument panel junction block assembly with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK OPERATION
11.CHECK OPERATION
a.

Check that the luggage compartment door entry unlock functions operate normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Luggage compartment door entry unlock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

12.INSPECT LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY
a.

Remove the luggage door opening switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH>REMOVAL


b.
B142645C21
1.479,1.417 1.26,1.885 false 1.719,1.427 1.938,1.885 false 0.135,0.104 0.313,0.271 0.177,0.167 10 *a 1.156,1.896 1.385,2.063 0.229,0.167 10 UL 1.906,1.896 2.052,2.063 0.146,0.167 10 E
*a Component without harness connected
(Luggage Door Opening Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (E) - 3 (UL) Luggage door opening switch assembly not pushed 10 kΩ or higher
2 (E) - 3 (UL) Luggage door opening switch assembly pushed Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - OPENING SWITCH)

NG

REPLACE LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - OPENING SWITCH)
a.

Disconnect the O1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the T4 luggage door opening switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O1-27 (TSW5) - T4-3 (UL) Always Below 1 Ω
O1-27 (TSW5) or T4-3 (UL) - Body ground Always 10 kΩ or higher
T4-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR