When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).
The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the intelligent tester with the engine switch off to troubleshoot:
Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
The door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".
Measure the voltage of the vehicle battery.
11 to 14 V
It may be possible to tell whether the vehicle battery is discharged by operating the horn.
If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.
| Proceed to |
|---|
| NEXT |
NEXT
Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.
Connect the intelligent tester and check for DTCs.
When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
DTC is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
When the door control switch on the multiplex network master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the following antennas in the key diagnostic mode.
Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter cannot be detected by channel 2 due to a malfunction, such as wave interference.
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (for driver door):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (for front passenger door):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna (front floor):
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna (rear floor):
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (outside luggage):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Wireless door lock buzzer sounds.
| Result | Proceed to |
|---|---|
| Diagnostic mode inspections fail for both channels | A |
| Diagnostic mode inspections succeed for both channels | B |
| Diagnostic mode inspection succeeds for only one of the channels | C |
A
B
C
Check if there are any other registered electrical key transmitter sub-assemblies.
| Result | Proceed to |
|---|---|
| There are no other registered electrical key transmitter sub-assemblies | A |
| There is another registered electrical key transmitter sub-assemblies | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.
Entry lock/unlock operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.
| Result | Proceed to |
|---|---|
| Transmitter LED does not illuminate when switch is pressed and held | A |
| Transmitter LED illuminates 3 times or more when switch is pressed and held | B |
| Transmitter LED illuminates once or twice but not a third time | C |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal and pressing the engine switch.
A
B
C
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Inspect the transmitter battery
Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate.
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
| *1 | Lead Wire |
Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.
| *1 | GND |
Measure the voltage of the transmitter battery.
When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement.
Perform the measurement when the key is at room temperature.
The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes".
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Transmitter battery positive (+) - Transmitter battery negative (-) | Engine switch off, all doors closed and lock sensor touched | 2.3 to 3.2 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
Wireless door lock buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
Wireless and entry functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ACC SW | Engine switch status | ON or OFF | ON: Engine switch on (ACC)
OFF: Engine switch off |
- |
| IG SW | Engine switch status | ON or OFF | ON: Engine switch to ON
OFF: Engine switch off |
- |
| Tester Display |
|---|
| ACC SW |
| IG SW |
If the certification ECU (smart key ECU assembly) misjudges that the power source is on even though the power source is off for any reason, the entry lock/unlock functions stop.
The main body ECU (multiplex network body ECU) judges properly that the power source is off when the power source is off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Disconnect the A43 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A43-11 (E) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A43-10 (CUTB) - Body ground | Always | 11 to 14 V |
| A43-2 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O1 certification ECU (smart key ECU assembly) connector.
Disconnect the O25 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O1-5 (RCO) - O25-4 (+5) | Always | Below 1 Ω |
| O1-17 (RDAM) - O25-5 (DATA) | Always | Below 1 Ω |
| O1-6 (CSEL) - O25-2 (CSEL) | Always | Below 1 Ω |
| O1-5 (RCO) or O25-4 (+5) - Body ground | Always | 10 kΩ or higher |
| O1-17 (RDAM) or O25-5 (DATA) - Body ground | Always | 10 kΩ or higher |
| O1-6 (CSEL) or O25-2 (CSEL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Door Control Receiver) |
Connect the O25 door control receiver connector.
Connect the O1 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O25-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Door Control Receiver) |
Connect the O1 certification ECU (smart key ECU assembly) connector.
Connect the O25 door control receiver connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O25-4 (+5) - O25-1 (GND) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly switch not pressed |
Below 1 V |
| Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly switch pressed |
4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the O1 certification ECU (smart key ECU assembly) connector.
Connect the O25 door control receiver connector.
| *a | Component with harness connected
(Door Control Receiver) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O25-5 (DATA) - O25-1 (GND) | Procedure:
1.
All doors closed 2.
All doors locked 3.
Electrical key transmitter sub-assembly switch pressed |
Below 1 V → 10 to 16 V → Below 1 V |
| O25-2 (CSEL) - O25-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors closed |
Below 1 V → Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the certification ECU (smart key ECU assembly) with a new one.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if there are any other registered electrical key transmitter sub-assemblies.
| Result | Proceed to |
|---|---|
| There are no other registered electrical key transmitter sub-assemblies | A |
| There is another registered electrical key transmitter sub-assemblies | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
Wireless door lock buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O1 certification ECU (smart key ECU assembly) connector.
Disconnect the O25 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O1-6 (CSEL) - O25-2 (CSEL) | Always | Below 1 Ω |
| O1-6 (CSEL) or O25-2 (CSEL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Door Control Receiver) |
Connect the O1 certification ECU (smart key ECU assembly) connector.
Connect the O25 door control receiver connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O25-2 (CSEL) - O25-1 (GND) | Engine switch off and all doors closed | Below 1 V → Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the O1 certification ECU (smart key ECU assembly) connector.
Connect the O25 door control receiver connector.
| *a | Component with harness connected
(Door Control Receiver) |
Measure the voltage according to the value(s) in the table below.
Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O25-5 (DATA) - O25-1 (GND) | Procedure:
1.
All doors closed 2.
All doors locked 3.
Electrical key transmitter sub-assembly switch pressed* |
Below 1 V → 10 to 16 V → Below 1 V |
*: While the electrical key antennas are being inspected in key diagnostic mode.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the certification ECU (smart key ECU assembly) with a new one.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG