Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074121 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


WIRING DIAGRAM

B298799E11
0.031,1.542 0.885,1.729 0.854,0.188 10 false from Battery 1.292,1.708 1.625,1.896 0.333,0.188 10 false AM2 4.948,6.917 5.198,7.073 0.25,0.156 10 false IG2 4.396,7.292 6.177,7.49 1.781,0.198 10 false No. 1 Integration Relay 2.188,1.552 2.406,1.698 0.219,0.146 10 false +B 2.615,1.052 2.958,1.198 0.344,0.146 10 false IG1D 2.615,6.625 2.958,6.771 0.344,0.146 10 false IG2D 2.208,5.896 2.333,6.042 0.125,0.146 10 false E 4.646,4.938 5.344,5.083 0.698,0.146 10 false IG1 NO. 4 3.625,5.365 6.292,5.51 2.667,0.146 10 false Instrument Panel Junction Block Assembly 1.646,7.156 3.5,7.521 1.854,0.365 10 false Certification ECU (Smart Key ECU Assembly) 4.646,3.74 5.344,3.885 0.698,0.146 10 false IG1 NO. 3 4.646,2.563 5.344,2.708 0.698,0.146 10 false IG1 NO. 2 4.656,1.375 5.354,1.521 0.698,0.146 10 false IG1 NO. 1 1.948,1.365 2.063,1.51 0.115,0.146 10 false 2 3.094,6.448 3.208,6.594 0.115,0.146 10 false 9 1.917,5.708 2.094,5.854 0.177,0.146 10 false 11 3.125,0.885 3.24,1.031 0.115,0.146 10 false 6 1.865,1.552 2.198,1.74 0.333,0.188 10 false A43 3.052,1.063 3.385,1.25 0.333,0.188 10 false I78 1.865,5.875 2.198,6.063 0.333,0.188 10 false A43 3.01,6.604 3.344,6.792 0.333,0.188 10 false A43 4.167,6.615 4.469,6.771 0.302,0.156 10 false 1C 5.823,6.615 6.104,6.771 0.281,0.156 10 false 1E 4.208,6.448 4.396,6.604 0.188,0.156 10 false 8 5.885,6.448 6.073,6.604 0.188,0.156 10 false 2 3.573,0.646 3.823,0.833 0.25,0.188 10 false 3E 3.594,0.469 3.781,0.615 0.188,0.146 10 false 3F 3.573,1.052 3.823,1.24 0.25,0.188 10 false 3A 3.594,0.885 3.802,1.031 0.208,0.146 10 false 27 6.188,0.646 6.438,0.833 0.25,0.188 10 false 3D 6.198,0.469 6.406,0.615 0.208,0.146 10 false 33 6.188,1.823 6.438,2.01 0.25,0.188 10 false 3D 6.188,1.656 6.396,1.802 0.208,0.146 10 false 36 6.188,3.01 6.438,3.198 0.25,0.188 10 false 3C 6.198,2.781 6.406,2.927 0.208,0.146 10 false 33 6.188,4.604 6.438,4.792 0.25,0.188 10 false 3B 6.24,4.448 6.448,4.594 0.208,0.146 10 false 7 5.521,0.792 6.271,0.99 0.75,0.198 10 false BKUP LP 5.625,2.01 6.208,2.375 0.583,0.365 10 false ECU-IG1 NO. 1 3.625,0.292 3.833,0.438 0.208,0.146 10 false 1 3.844,0.74 4.052,0.885 0.208,0.146 10 false *1 3.854,0.479 4.063,0.625 0.208,0.146 10 false *2 0.188,7.063 0.948,7.26 0.76,0.198 10 false *1: for LHD 0.188,7.365 0.948,7.563 0.76,0.198 10 false *2: for RHD 5.646,3.188 6.219,3.531 0.573,0.344 10 false ECU-IG1 NO. 3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART).

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IG1 Relay Monitor (Inside)

·

IG2 Relay Monitor (Inside)

·

IG1 Relay Monitor (Outside)

·

IG2 Relay Monitor (Outside)

·

IG1 Circuit

·

IG2 Circuit


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)
a.

Disconnect the A43 connector from the certification ECU (smart key ECU assembly).


b.

Disconnect the 1C and 1E connectors from the No. 2 integration relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-9 (IG2D) - 1C-8 Always Below 1 Ω
1E-2 - Body ground Always Below 1 Ω
A43-9 (IG2D) or 1C-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT NO.1 INTEGRATION RELAY (IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO.1 INTEGRATION RELAY (IG2 RELAY)
a.

Remove the No. 1 integration relay.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>INTEGRATION RELAY>REMOVAL


b.

Inspect the No. 1 integration relay.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the I78 connector from the certification ECU (smart key ECU assembly).


b.

Disconnect the 3A and 3B connectors from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-6 (IG1D) - 3A-27 Always Below 1 Ω
3B-7 - Body ground Always Below 1 Ω
I78-6 (IG1D) and 3A-27 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO.2 AND IG1 NO. 3 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO.2 AND IG1 NO. 3 RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

B281391C06
5.007,0.185 5.356,0.433 0.348,0.248 5.098,0.25 5.421,0.467 0.323,0.217 10 3B 3.354,2.573 3.702,2.821 0.348,0.248 3.454,2.628 3.777,2.845 0.323,0.217 10 3E 5.05,1.413 5.398,1.661 0.348,0.248 5.14,1.479 5.463,1.696 0.323,0.217 10 3D 1.939,0.171 2.287,0.419 0.348,0.248 2.03,0.236 2.352,0.453 0.323,0.217 10 3A 1.925,1.39 2.273,1.638 0.348,0.248 2.016,1.455 2.338,1.672 0.323,0.217 10 3C 3.789,2.573 4.137,2.821 0.348,0.248 3.888,2.628 4.211,2.802 0.323,0.175 10 3F 3.412,2.403 3.612,2.62 0.2,0.217 10 *A 3.874,2.403 4.074,2.62 0.2,0.217 10 *B 0.157,0.068 0.403,0.285 0.246,0.217 10 *a
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
·

3E-1 - 3D-33 (IG1 No. 1 relay)

·

3E-1 - 3D-36 (IG1 No. 2 relay)

·

3E-1 - 3C-33 (IG1 No. 3 relay)

·

3E-1 - 3C-14 (IG1 No. 4 relay)


Battery voltage not applied to terminals 3A-27 and 3B-7 10 kΩ or higher
Battery voltage applied to terminals 3A-27 and 3B-7 Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
·

3F-1 - 3D-33 (IG1 No. 1 relay)

·

3F-1 - 3D-36 (IG1 No. 2 relay)

·

3F-1 - 3C-33 (IG1 No. 3 relay)

·

3F-1 - 3C-14 (IG1 No. 4 relay)


Battery voltage not applied to terminals 3A-27 and 3B-7 10 kΩ or higher
Battery voltage applied to terminals 3A-27 and 3B-7 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the A43 and I78 certification ECU (smart key ECU assembly) connectors.

B264896C21
0.302,0.29 0.488,0.451 0.186,0.161 10 *a 4.729,0.887 5.126,1.126 0.397,0.238 4.841,0.934 5.136,1.091 0.296,0.157 10 I78 2.111,0.885 2.508,1.123 0.397,0.238 2.187,0.932 2.482,1.088 0.296,0.157 10 A43 4.388,1.629 4.13,2.287 false 1.978,1.736 1.762,2.287 false 3.927,2.312 4.29,2.468 0.363,0.157 10 IG1D 1.531,2.313 1.894,2.469 0.363,0.157 10 IG2D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-9 (IG2D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher
I78-6 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)