Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074131 ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set (no key is in the ignition key cylinder).

·

w/ Theft Deterrent System:

The main body ECU (multiplex network body ECU) blinks the security indicator light when the theft deterrent system is in the arming preparation state or alarm sounding state.


WIRING DIAGRAM

B271008E07
4.49,1.101 4.806,1.257 0.316,0.156 10 I19 4.448,2.964 4.723,3.121 0.274,0.156 10 I12 4.49,1.269 6.082,1.578 1.591,0.309 10 Transponder Key ECU Assembly 4.448,3.104 6.105,3.413 1.656,0.309 10 Main Body ECU (Multiplex Network Body ECU) 1.209,1.21 1.483,1.366 0.274,0.156 10 I56 1.209,1.378 3.335,1.745 2.126,0.367 10 Security Indicator Light (Air Conditioning Control Assembly)*1 1.209,1.966 3.233,2.333 2.024,0.367 10 Security Indicator Light (Heater Control Switch Board)*2 4.771,0.569 5.031,0.739 0.26,0.17 10 IND 2.445,0.597 2.657,0.767 0.212,0.17 10 LP 1.719,0.597 2.171,0.767 0.453,0.17 10 GND 4.771,2.481 5.031,2.651 0.26,0.17 10 IND 4.589,0.498 4.745,0.655 0.156,0.156 10 8 4.538,2.39 4.715,2.546 0.177,0.156 10 22 2.746,0.498 2.958,0.655 0.212,0.156 10 1 1.532,0.498 1.718,0.655 0.186,0.156 10 6 3.636,2.329 3.813,2.485 0.177,0.156 10 *3 0.441,3.459 3.855,3.616 3.413,0.156 10 *3: w/ Theft Deterrent System 0.441,3.149 3.619,3.305 3.177,0.156 10 *2: w/ Automatic Air Conditioning Control System 0.441,2.838 3.438,2.994 2.997,0.156 10 *1: w/ Manual Air Conditioning Control System

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
w/ Theft Deterrent System A
w/o Theft Deterrent System B



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)

B

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser or Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light OFF/ON -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Security Indicator
50004 123 19
Result:
Result Proceed to
Security indicator light operation is normal when performing the "Main Body" and "Immobiliser" Active Test A
·

Security indicator light operation is not normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is normal when performing the "Main Body" Active Test


B
·

Security indicator light operation is normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is not normal when performing the "Main Body" Active Test


C
Security indicator light operation is not normal when performing the "Main Body" and "Immobiliser" Active Test D




A

3.CHECK SECURITY INDICATOR LIGHT OPERATION

B

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (AIR CONDITIONING CONTROL ASSEMBLY) - TRANSPONDER KEY ECU ASSEMBLY)

C

5.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (AIR CONDITIONING CONTROL ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

D

6.CHECK HARNESS AND CONNECTOR
3.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks.*1

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light on.*2

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION

OK:

The security indicator light is on normally.


Result:
Result Proceed to
Both *1 and *2 are OK A
*1 is NG (*2 is OK) B
*2 is NG (*1 is OK) C
Both *1 and *2 are NG D




A

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

D

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (AIR CONDITIONING CONTROL ASSEMBLY) - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the security indicator light (air conditioning control assembly) connector.


b.

Disconnect the transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I19-8 (IND) - I56-1 (LP) Always Below 1 Ω
I19-8 (IND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (AIR CONDITIONING CONTROL ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the security indicator light (air conditioning control assembly) connector.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-22 (IND) - I56-1 (LP) Always Below 1 Ω
I12-22 (IND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR
a.

Disconnect the security indicator light (air conditioning control assembly) connector.


b.

Disconnect transponder key ECU assembly connector.


c.

Disconnect the main body ECU (multiplex network body ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I19-8 (IND) - I56-1 (LP) Always Below 1 Ω
I12-22 (IND) - I56-1 (LP) Always Below 1 Ω
I56-1 (LP) - Body ground Always 10 kΩ or higher
I56-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.REPLACE SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD)
a.

Temporarily replace the security indicator light (air conditioning control assembly) with a new or known good one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL(for Automatic Air Conditioning System)>REMOVAL


b.

When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.



Result:
Proceed to
OK
NG



OK

END (HEATER CONTROL SWITCH BOARD WAS DEFECTIVE)

NG

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY
8.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new or known good one.

HINT:

Refer to Service Bulletin.



b.

When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light OFF/ON -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
Result:
Proceed to
OK
NG




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - TRANSPONDER KEY ECU ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the security indicator light (air conditioning control assembly)*1 or security indicator light (heater control switch board)*2 connector.

*1: w/ Manual Air Conditioning System

*2: w/ Automatic Air Conditioning System



b.

Disconnect the transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I19-8 (IND) - I56-1 (LP) Always Below 1 Ω
I19-8 (IND) - Body ground Always 10 kΩ or higher
I56-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK TRANSPONDER KEY ECU ASSEMBLY
a.

Reconnect the transponder key ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
I19-8 (IND) - Body ground No key in ignition key cylinder, or 20 sec. elapsed after turning the ignition switch to on (ACC) or off (engine immobiliser set) Pulse generation
I19-8 (IND) - Body ground Key in ignition key cylinder (engine immobiliser system unset) Below 1 V


Result:
Result Proceed to
OK (w/ Manual Air Conditioning System) A
OK (w/ Automatic Air Conditioning System) B
NG C



A

REPLACE SECURITY INDICATOR LIGHT (AIR CONDITIONING CONTROL ASSEMBLY)

B

C

REPLACE TRANSPONDER KEY ECU ASSEMBLY