Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR
RM19V0EQ _58 Vehicle Interior _014610 SUPPLEMENTAL RESTRAINT SYSTEMS _0074157 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89860C 1.INSTALL SIDE NO. 2 AIRBAG SENSOR ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B296255C07
4.76,1.833 5.042,2.146 0.281,0.313 10 false *b 1.396,1.833 1.688,2.115 0.292,0.281 10 false *b 4.76,0.573 5.052,0.844 0.292,0.271 10 false *a 1.396,0.573 1.677,0.885 0.281,0.313 10 false *a
*a Incorrect *b Correct



d.

Insert the pin (stopper) into the body hole and install the side No. 2 airbag sensor assembly to the vehicle body with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the side No. 2 airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the side No. 2 airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the pin (stopper) is securely inserted into the body hole.

·

Tighten the bolt while holding the side No. 2 airbag sensor assembly because the side No. 2 airbag sensor assembly pin (stopper) is easily damaged.




e.

Connect the connector to the side No. 2 airbag sensor assembly.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

B312074C01
2.208,0.802 2.385,0.531 true 2.385,0.531 2.583,0.531 false 2.406,1 2.583,0.729 true 2.583,0.729 2.76,0.729 false 2.469,1.396 2.469,1.719 false 2.802,0.646 3.01,0.854 0.208,0.208 10 false *1 2.396,1.729 2.635,1.948 0.24,0.219 10 false *2 5.938,3.365 6.208,3.615 0.271,0.25 10 false *a 2.646,0.438 2.896,0.667 0.25,0.229 10 false (A)
*1 White Housing Lock *2 Yellow CPA
*a Connection is Completed - -


HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.




f.

Check that there is no looseness in the installation parts of the side No. 2 airbag sensor assembly.


Hide 72693 3.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION