Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2011.10–2013.07
RM19V0EQ _58 Vehicle Interior _014613 HEATING / AIR CONDITIONING _0074181 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 1.INSTALL AIR CONDITIONING UNIT ASSEMBLY

a.

Install the air conditioning unit assembly to the instrument panel reinforcement assembly with the 3 bolts.

E227855E01
3.104,1.323 3.24,1.167 false 2.375,1.271 2.563,1.625 false 2.5,1.594 2.885,1.865 0.385,0.271 10 false <1> 5.323,0.823 5.708,1.094 0.385,0.271 10 false <2> 2.906,1.302 3.188,1.51 0.281,0.208 10 false <3>

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration to install the air conditioning unit assembly.



Hide 2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT

NOTICE:
·

Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When installing the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

Engage the 3 guides and temporarily install the instrument panel reinforcement assembly with air conditioning unit as shown in the illustration.

E238963


b.

Install the instrument panel reinforcement assembly with the 3 bolts <A> and 2 new bolts <B>.

E238936C03
3.396,1.458 3.167,1.552 false 3.677,1.333 3.865,1.135 false 3.802,1.677 3.917,1.583 false 0.042,3.063 0.469,3.313 0.427,0.25 10 false <1> 0.073,3.271 0.552,3.51 0.479,0.24 10 false <2> 0.094,3.656 0.51,3.917 0.417,0.26 10 false <3> 6.219,2.365 6.656,2.615 0.438,0.25 10 false <4> 6.229,2.698 6.688,2.938 0.458,0.24 10 false <5> 3,1.49 3.375,1.74 0.375,0.25 10 false *1 3.896,1 4.271,1.208 0.375,0.208 10 false *2 3.917,1.469 4.26,1.74 0.344,0.271 10 false *3 2.177,0.583 2.51,0.792 0.333,0.208 10 false *a 3.146,0.583 3.469,0.802 0.323,0.219 10 false *b 4.135,0.583 4.563,0.844 0.427,0.26 10 false *c 5.177,0.583 5.594,0.854 0.417,0.271 10 false *d 0.042,2.823 0.573,3.052 0.531,0.229 10 false <A> 0.344,3.271 0.927,3.552 0.583,0.281 10 false <A> 0.396,3.604 0.865,3.854 0.469,0.25 10 false <A> 5.969,2.5 6.438,2.708 0.469,0.208 10 false <B> 6.021,2.823 6.531,3.063 0.51,0.24 10 false <B>
*1 Movable Collar *2 Body
*3 Instrument Panel Reinforcement - -
*a Step 1 *b Step 2
*c Step 3 *d Step 4


Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration to install the reinforcement assembly.



c.

Install the instrument panel reinforcement assembly with air conditioning unit with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


d.

Install the bolt.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


e.
E227180E01
2,1.115 2.292,1.292 0.292,0.177 10 true <1> 0.531,0.896 0.896,1.115 0.365,0.219 10 false <2>

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration.



f.

Engage each clamp.


g.

Connect the connector.


h.

Connect the connector holder with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


i.

Install the bolt and connect the earth wires.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


j.

Engage each clamp.


k.

Connect the connector.


l.

Install the 2 bolts and connect the 2 earth wires.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


m.

Connect the connector.


n.
E231353

Pass the drain cooler hose through the vehicle securely.

NOTICE:

Connect the cooler drain hose firmly to prevent water leaks.



o.

Engage each clamp.


p.

Engage the claw to connect the airbag connector as shown in the illustration.

E227176


q.
E227174C08
2.073,2.677 2.458,2.948 false 2.51,2.896 2.813,3.177 0.302,0.281 10 false *1
*1 Retainer


Engage the 2 claws to lock the retainer as shown in the illustration.


r.

for Automatic Transaxle:

i.
E236048C05
0.896,3.844 0.219,3.469 0.219,3.469 0.594,4.021 false 2,0.365 2.292,0.656 0.292,0.292 10 false *1 0.01,3.333 0.365,3.615 0.354,0.281 12 false *A
*A w/ Smart Entry and Start System
*1 Airbag Sensor Assembly


Engage each clamp.


ii.

Connect each connector.


iii.

Connect the connector to the airbag sensor assembly as shown in the illustration.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



iv.
E227170

Engage the 3 claws to close the 3 clamps as shown in the illustration.



s.

for Manual Transaxle:

i.

Connect the 2 connectors.


ii.
E234840C01
1.875,0.146 2.26,0.365 0.385,0.219 10 false *1
*1 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly as shown in the illustration.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



iii.
E234838

Engage the 3 claws to close the 3 clamps as shown in the illustration.



t.

for 10 Speakers:

i.

Engage the 3 clamps.



Hide 3.INSTALL FRONT LOWER PANEL PACKING

a.
E227178

Install the 2 front lower panel packings.


Hide 55458A 4.INSTALL INSTRUMENT PANEL SAFETY PAD CAP

a.

Install 5 new instrument panel safety pad caps.

E265294C03
0.667,0.219 1.156,0.5 0.49,0.281 12 false *A 3.844,0.219 4.281,0.521 0.438,0.302 12 false *B
*A for Driver Side *B for Passenger Side



Hide 55307E 5.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the screw and 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Install the No. 2 instrument panel brace sub-assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Connect the earth wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Engage each clamp.


e.

Connect the connector.


Hide 55306B 6.INSTALL INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.

Install the screw and 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Install the instrument panel to cowl brace sub-assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Connect the earth wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Engage each clamp.


e.

Connect each connector.


Hide 58861B 7.INSTALL NO. 1 CONSOLE BOX DUCT

a.

Install the No. 1 console box duct with the clip.


Hide 87212F 8.INSTALL REAR NO. 2 AIR DUCT

a.

Engage the 2 claws to install the rear No. 2 air duct.


Hide 58544A 9.INSTALL FLOOR CARPET BRACKET LH

a.

Engage the 2 guides.


b.

Install the floor carpet bracket LH with the 2 clips.


c.
E227459

Engage the guide to install the floor carpet to the original position as shown in the illustration.


Hide 77306 10.CONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

a.
E227151

Engage the guide to connect the fuel lid lock open lever sub-assembly as shown in the illustration.


b.

Install the screw.


Hide 87212 11.INSTALL REAR NO. 1 AIR DUCT

a.

Engage the 2 claws to install the rear No. 1 air duct.


Hide 58543B 12.INSTALL FLOOR CARPET BRACKET RH

a.

Engage the 2 guides.


b.

Install the floor carpet bracket RH with the 2 clips.


c.
E229495

Engage the guide to install the floor carpet to the original position as shown in the illustration.


Hide 58521B 13.INSTALL FLOOR CARPET HOOK

a.

Engage the 6 claws to install the 6 floor carpet hooks.


b.

Engage the 6 guides.


Hide 85940 14.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)

Hide 88650N 15.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 82730 17.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)

Hide 82730 18.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for RHD)

Hide 19.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 20.INSTALL STEERING POST ASSEMBLY

Hide 21.INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers)

Hide 86183D 22.INSTALL AUDIO AMPLIFIER COVER (for 10 Speakers)

Hide 23.INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)

Hide 24.INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

Hide 25.INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)

HINT:

Use the same procedure for the RH side and LH side.


Hide 26.INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)

HINT:

Use the same procedure for the RH side and LH side.


Hide 88710E 27.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the pipe.


b.

Sufficiently apply compressor oil to a new O-ring and fitting surface of the air conditioner tube and accessory assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.


d.

Connect the air conditioner tube and accessory assembly.


Hide 88704 28.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.


d.
E227143

Move the hook connector in the direction indicated by the arrow in the illustration.


e.

Insert the pipe joint into the fitting hole securely and tighten the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87245 29.CONNECT HEATER INLET WATER HOSE

a.

Using pliers, grip the claws of the clip and slide the clip to connect the heater inlet water hose.


Hide 87246 30.CONNECT HEATER OUTLET WATER HOSE

a.

Using pliers, grip the claws of the clip and slide the clip to connect the heater outlet water hose.


Hide 55701J 31.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 32.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 33.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 35.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR

Hide 37. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 40.INITIALIZATION SERVO MOTOR (for Manual Air Conditioning System)

Hide 41.INITIALIZATION SERVO MOTOR (for Automatic Air Conditioning System)