Home › Vehicle Interior › HEATING / AIR CONDITIONING › REFRIGERANT
RM19V0EQ _58 Vehicle Interior _014613 HEATING / AIR CONDITIONING _0074182 REFRIGERANT A

HEATING / AIR CONDITIONING  REFRIGERANT  REPLACEMENT  


PROCEDURE

Hide 1. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM

a.

Turn the ignition switch to ON.


b.

Turn the A/C switch on.


c.

Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.


d.

Turn the ignition switch off.


e.

Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.


Hide 2. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

a.

Perform vacuum purging using a vacuum pump or appropriate equipment.


b.

Charge the air conditioning system with refrigerant.

Refrigerant type:

HFC-134a (R134a)


E143108C19
3.656,2 4.021,2.229 0.365,0.229 10 false *i 1.854,4.208 2.25,4.521 0.396,0.313 10 false :*a 3.135,0.958 3.531,1.219 0.396,0.26 10 false *e 4.25,1.198 4.656,1.479 0.406,0.281 10 false *g 3.167,2.896 3.521,3.146 0.354,0.25 10 false *f 2.406,0.5 2.781,0.771 0.375,0.271 10 false *d 3.792,3.698 4.125,3.979 0.333,0.281 10 false *c 0.896,2.125 1.146,2.375 0.25,0.25 10 false *b 4.708,2.146 5.042,2.396 0.333,0.25 10 false *h
*a Sub-cool System *b High Pressure
*c Refrigerant Amount *d Standard charge amount
*e Charge additional 100 g (3.5 oz.) *f Point where bubbles disappear
*g Mean value in proper range *h Overcharged
*i +/- 50 g (+/- 1.80 oz.) - -


Standard charge amount:

450 to 550 g (15.9 to 19.4 oz.)


SST
09985-20010  (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

NOTICE:
·

Do not turn the A/C switch on before charging the air conditioning system with refrigerant. Doing so may cause the compressor to work without refrigerant, resulting in overheating of the compressor.

·

The refrigerant amount should be checked by quantity (weight).



HINT:

Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an air conditioning system.



Hide 3. WARM UP ENGINE

a.

Keep the A/C switch on for at least 2 minutes to warm up the compressor.

NOTICE:

To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing air conditioning system lines (including the compressor).



Hide 4.INSPECT FOR REFRIGERANT LEAK

a.

After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.


b.

Carry out the test under the following conditions:

·

Ignition switch off.

·

Secure good ventilation (the halogen leak detector may react to volatile gases which are not refrigerant, such as gasoline vapor and exhaust gas).

·

Repeat the inspection 2 or 3 times.

·

Measure the pressure to make sure that there is some refrigerant remaining in the air conditioning system.

Pressure when the compressor is off: approx. 392 to 588 kPa (3.9 to 5.9 kgf/cm2, 57 to 85 psi)



c.

Remove the windshield wiper motor and link assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL


d.

Remove the front outer cowl top panel sub-assembly.

for LHD:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for LHD)>REMOVAL

for RHD:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for RHD)>REMOVAL


e.

Remove the front bumper assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REMOVAL


f.

Remove the radiator side deflector RH.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER>REMOVAL


g.
E280082C01
1.875,0.615 2.333,0.615 false 0.333,0.167 0.646,0.365 0.313,0.198 10 false *a 2.354,0.51 2.667,0.708 0.313,0.198 10 false *b 1.708,0.927 2.021,1.125 0.313,0.198 10 false *c 1.854,1.958 2.167,2.156 0.313,0.198 10 false *d
*a Check for leaks
*b Halogen Leak Detector Sensor
*c Distance between Sensor and Joint to be Checked:
10 mm or less
*d Halogen Leak Detector Sensor Moving Speed:
25 to 50 mm/sec.


How to check for refrigerant leaks in pipe joints:

NOTICE:

Gas leaking from a joint can be dissipated by even the slightest breeze. Move the halogen leak detector sensor 360° around each joint instead of keeping it in one spot when checking.



h.

Using a halogen leak detector, check for refrigerant leaks at the pipe joints shown in the illustration.

E288036C01
0.458,0.667 0.719,0.698 false 0.438,1.823 0.885,2.01 false 0.354,2.594 0.688,2.344 false 0.99,3.677 1.313,3.51 false 0.969,4.031 1.427,3.802 false 5.844,3.667 6.208,3.854 false 6.813,4.271 6.646,3.969 false 6.333,0.823 6.76,0.844 6.76,0.844 6.365,0.594 false 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.281,0.552 0.479,0.74 0.198,0.188 10 true *c 0.188,2.521 0.5,2.719 0.313,0.198 10 false *d 0.271,1.698 0.583,1.896 0.313,0.198 10 false *b 6.781,0.75 6.979,0.938 0.198,0.188 10 false *e 1.448,3.646 1.76,3.844 0.313,0.198 10 false *g 6.781,4.292 6.979,4.49 0.198,0.198 10 true *h 5.719,3.542 6.031,3.74 0.313,0.198 10 false *i 1.333,3.385 1.646,3.583 0.313,0.198 10 false *f
*a Area to be Checked *b Service Valve (High)
*c Service Valve (Low) *d Air Conditioner Pressure Sensor Joint
*e Cooler Expansion Valve Joint *f Condenser Joint (Inlet)
*g Condenser Joint (Outlet) *h Compressor Joint (Inlet)
*i Compressor Joint (Outlet) - -


NOTICE:
·

After the blower motor has stopped, leave the cooling unit for more than 15 minutes.

·

Disconnect the pressure sensor connector and leave it for approximately 20 minutes.

·

When checking for leaks, the presence of oily dirt at a joint can indicate a leak.



Standard:

There are no refrigerant leaks from the joints.

If refrigerant is leaking, disconnect the leaking joint and visually check for the cause, such as the presence of foreign matter.



i.
E280081C01
0.844,1.083 1.26,1.083 false 1.083,1.469 1.083,1.802 false 0.677,0.979 0.99,1.177 0.313,0.198 10 false *1 1.021,1.813 1.333,2.01 0.313,0.198 10 false *a
*1 Drain Cooler Hose
*a Halogen Leak Detector


Bring the halogen leak detector sensor close to the drain cooler hose with the detector turned off, and then turn the detector on.

NOTICE:

Keep water away from the halogen leak detector to prevent malfunction.


HINT:
·

After the blower motor has stopped, leave the cooling unit for more than 15 minutes.

·

When bringing the halogen leak detector sensor close to the drain cooler hose, make sure that the halogen leak detector does not react to volatile gases. If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow checking for leaks.



Standard:

Refrigerant is not leaking from the drain cooler hose.

If refrigerant is leaking, check for refrigerant leaks from the No. 1 cooler evaporator sub-assembly.



j.

Remove the blower motor with fan sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>REMOVAL


k.
E288039C01
2.667,1.74 2.75,1.438 false 0.563,0.188 1.135,0.323 false 0.385,0.073 0.698,0.271 0.313,0.198 10 false *1 2.594,1.75 2.906,1.948 0.313,0.198 10 false *a
*1 No. 1 Cooler Evaporator Sub-assembly
*a Halogen Leak Detector


Insert the halogen leak detector sensor into the air conditioning unit assembly, bring the sensor close to the No. 1 cooler evaporator sub-assembly and check for refrigerant leaks.

HINT:

After the blower motor has stopped, leave the cooling unit for more than 15 minutes.


Standard:

Refrigerant is not leaking from the No. 1 cooler evaporator sub-assembly.

If refrigerant is leaking, disconnect the leaking joint and visually check for the cause, such as the presence of foreign matter.



l.

Install the blower motor with fan sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>INSTALLATION


m.

Install the radiator side deflector RH.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER>INSTALLATION


n.

Install the front bumper assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION


o.

Install the front outer cowl top panel sub-assembly.

for LHD:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for LHD)>INSTALLATION

for RHD:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for RHD)>INSTALLATION


p.

Install the windshield wiper motor and link assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION