Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM19V0EQ _58 Vehicle Interior _014613 HEATING / AIR CONDITIONING _0074197 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1446/46  Air Mix Damper Control Servo Motor Circuit (Driver Side)  


DESCRIPTION

1. for LHD

The No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) to any position. As a result, the amount of air passing through the heater core after passing through the evaporator is adjusted, and the temperature of the air blowing toward the driver seat side is controlled.

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.


2. for RHD

The No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) to any position. As a result, the amount of air passing through the heater core after passing through the evaporator is adjusted, and the temperature of the air blowing toward the driver seat side is controlled.

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1446/46 Air Mix Damper Control Servo Motor Circuit (Driver Side) for LHD:
Air mix damper position sensor value does not change even if air conditioning amplifier assembly operates No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side)
for RHD:
Air mix damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side)
·

No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side)*2

·

No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side)*3

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized
(30 sec. or more)*1

*1: The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.

*2: for LHD

*3: for RHD


WIRING DIAGRAM

E229253
5.728,2.197 5.825,2.372 0.098,0.175 10 3 5.728,1.245 5.825,1.419 0.098,0.175 10 4 5.948,2.291 6.405,2.466 0.457,0.175 10 BUS 5.948,3.247 6.405,3.422 0.457,0.175 10 BUS G 5.54,4.094 5.782,4.269 0.243,0.175 10 z1 5.54,4.253 7.144,4.586 1.604,0.332 10 Air Conditioning Amplifier Assembly 0.05,4.108 2.939,4.441 2.888,0.332 10 No. 2 Air Conditioning Radiator Damper Servo Sub-assembly (Air Mix for Driver Side)*1 0.05,4.775 2.943,5.107 2.892,0.332 10 No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Air Mix for Driver Side)*2 5.728,3.151 5.825,3.326 0.098,0.175 10 2 5.948,1.339 6.391,1.513 0.443,0.175 10 B BUS 3.325,4.094 4.88,4.45 1.556,0.355 10 Air Conditioning Harness Assembly 4.491,4.847 5.363,5.003 0.871,0.156 10 *1: for LHD 4.491,5.268 5.363,5.423 0.871,0.156 10 *2: for RHD

CAUTION / NOTICE / HINT

HINT:

Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.


PROCEDURE

1.CONFIRM MODEL
Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER

NG

6.READ VALUE USING INTELLIGENT TESTER
2.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Operate the driver side temperature adjustment switch.


e.

Enter the following menus: Body / Air Conditioner / Data List.


f.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Air Mix Servo Actual Pulse(D) No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) actual pulse Min.: 0, Max.: 255 MAX COLD: 5 (pulse)
MAX HOT: 103 (pulse)
-
Body Electrical > Air Conditioner > Data List
Tester Display
Air Mix Servo Actual Pulse(D)
50003 121 128
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) pulse Min.: 0, Max.: 255 Operates between 5 and 103 pulses
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(D)
50004 121 24
OK:

Air temperature changes in accordance with each control range.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

4.REPLACE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX FOR DRIVER SIDE)
4.REPLACE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX FOR DRIVER SIDE)
a.

Replace the No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Body Electrical > Air Conditioner > Trouble Codes
50001 121
Result:
Result Proceed to
DTC B1446/46 is output A
DTC B1446/46 is not output B




A

5.REPLACE AIR CONDITIONING HARNESS ASSEMBLY

B

END (NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX FOR DRIVER SIDE) WAS DEFECTIVE)

5.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
a.

Replace the air conditioning harness assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Body Electrical > Air Conditioner > Trouble Codes
50001 121
Result:
Result Proceed to
DTC B1446/46 is output A
DTC B1446/46 is not output B




A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)

6.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Operate the driver side temperature adjustment switch.


e.

Enter the following menus: Body / Air Conditioner / Data List.


f.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Air Mix Servo Actual Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) actual pulse Min.: 0, Max.: 255 MAX COLD: 105
MAX HOT: 7
-
Body Electrical > Air Conditioner > Data List
Tester Display
Air Mix Servo Actual Pulse(D)
50003 121 128
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) pulse Min.: 0, Max.: 255 Operates between 7 and 105 pulses
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(D)
50004 121 24
OK:

Air temperature changes in accordance with each control range.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

8.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX FOR DRIVER SIDE)
8.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX FOR DRIVER SIDE)
a.

Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Body Electrical > Air Conditioner > Trouble Codes
50001 121
Result:
Result Proceed to
DTC B1446/46 is output A
DTC B1446/46 is not output B




A

9.REPLACE AIR CONDITIONING HARNESS ASSEMBLY

B

END (NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX FOR DRIVER SIDE) WAS DEFECTIVE)

9.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
a.

Replace the air conditioning harness assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Body Electrical > Air Conditioner > Trouble Codes
50001 121
Result:
Result Proceed to
DTC B1446/46 is output A
DTC B1446/46 is not output B




A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)