Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM19V0EQ _58 Vehicle Interior _014613 HEATING / AIR CONDITIONING _0074197 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1451/51  Compressor Solenoid Circuit  


DESCRIPTION

In this circuit, the compressor assembly with pulley (compressor solenoid) receives a refrigerant compression demand signal from the air conditioning amplifier assembly.

Based on this signal, the compressor assembly with pulley (compressor solenoid) changes the amount of compressor output.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1451/51 Compressor Solenoid Circuit Open or short in compressor solenoid circuit
·

Compressor assembly with pulley (compressor solenoid)

·

Harness or connector between air conditioning amplifier assembly and cooler compressor assembly (compressor solenoid)

·

Air conditioning amplifier assembly


-

WIRING DIAGRAM

E229254
5.011,0.794 5.109,0.969 0.098,0.175 10 2 3.838,0.794 3.936,0.969 0.098,0.175 10 2 2.444,0.794 2.542,0.969 0.098,0.175 10 1 5.231,0.888 5.688,1.062 0.457,0.175 10 SOL+ 3.385,0.794 3.765,0.969 0.38,0.175 10 SOL+ 2.667,0.794 3.015,0.969 0.348,0.175 10 SOL- 4.823,3.503 5.163,3.678 0.34,0.175 10 I77 4.823,3.662 6.464,3.995 1.641,0.332 10 Air Conditioning Amplifier Assembly 2.247,1.493 4.364,1.817 2.118,0.324 10 Compressor Assembly with Pulley (Compressor Solenoid) 2.247,1.334 2.512,1.509 0.265,0.175 10 E74

PROCEDURE

1.INSPECT COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID)
a.
E229635
2.49,1.677 2.927,1.969 0.438,0.292 1.5,2 1.25,2.417 false 1.969,1.979 2.219,2.396 false 0.167,0.219 0.625,0.781 0.458,0.563 10 false *a 2.604,1.74 3.083,2.021 0.479,0.281 10 false E74 2.115,2.438 2.708,2.729 0.594,0.292 10 false SOL- 1.021,2.448 1.625,2.74 0.604,0.292 10 false SOL+
*a Component without harness connected
(Compressor Assembly with Pulley (Compressor Solenoid))


Disconnect the E74 compressor assembly with pulley (compressor solenoid) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E74-2 (SOL+) - E74-1 (SOL-) 20°C (68°F) 10 to 11 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - BODY GROUND)

NG

REPLACE COMPRESSOR ASSEMBLY WITH PULLEY

2.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E74-1 (SOL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the I77 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I77-2 (SOL+) - E74-2 (SOL+) Always Below 1 Ω
I77-2 (SOL+) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY