The No. 1 air conditioning radiator damper servo sub-assembly (air mix) sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the No. 1 air conditioning radiator damper servo sub-assembly (air mix) to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the output air.
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1441 | Air Mix Damper Control Servo Motor Circuit (Passenger Side) | Air mix damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 air conditioning radiator damper servo sub-assembly (air mix) | ·
No. 1 air conditioning radiator damper servo sub-assembly (air mix) ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Memorized
(30 sec. or more)*1 |
*1: The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.
Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Operate the temperature adjustment switch.
Enter the following menus: Body / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Air Mix Servo Actual Pulse(D) | No. 1 air conditioning radiator damper servo sub-assembly (air mix) actual pulse | Min.: 0
Max.: 255 |
for LHD:
MAX. COLD: 105 (pulse) MAX. HOT: 7 (pulse) for RHD: MAX. COLD: 5 (pulse) MAX. HOT: 103 (pulse) |
- |
| Tester Display |
|---|
| Air Mix Servo Actual Pulse(D) |
The display is as specified in the normal condition column.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC) | C |
A
B
C
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pulse(D) | No. 1 air conditioning radiator damper servo sub-assembly (air mix) pulse | Min.: 0, Max.: 255 | for LHD: Operates between 7 and 105 pulses
for RHD: Operates between 5 and 103 pulses |
| Tester Display |
|---|
| Air Mix Servo Targ Pulse(D) |
Air temperature changes in accordance with each control range.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1441 is output | A |
| DTC B1441 is not output | B |
A
B
Replace the air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1441 is output | A |
| DTC B1441 is not output | B |
A
B