Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM19V0EQ _58 Vehicle Interior _014613 HEATING / AIR CONDITIONING _0074198 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1442  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 blower damper servo sub-assembly (air inlet) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal, reverse) based on the signals to move the air inlet mode selection No. 1 blower damper servo sub-assembly (air inlet) to any position, which controls the intake air settings (FRESH, FRESH/RECIRCULATION, and RECIRCULATION).

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1442 Air Inlet Damper Control Servo Motor Circuit Air inlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 blower damper servo sub-assembly (air inlet)
·

No. 1 blower damper servo sub-assembly (air inlet)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized
(30 sec. or more)*1

*1: The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E229253
5.729,2.188 5.823,2.365 0.094,0.177 10 false 3 5.729,1.24 5.823,1.417 0.094,0.177 10 false 4 5.948,2.281 6.406,2.458 0.458,0.177 10 false BUS 5.948,3.24 6.406,3.417 0.458,0.177 10 false BUS G 5.5,4.083 5.74,4.26 0.24,0.177 10 false z1 5.5,4.24 7.063,4.677 1.563,0.438 10 false Air Conditioning Amplifier Assembly 0.396,4.104 2.469,4.542 2.073,0.438 10 false No. 1 Blower Damper Servo Motor Sub-assembly (Air Inlet) 5.729,3.146 5.823,3.323 0.094,0.177 10 false 2 5.948,1.333 6.396,1.51 0.448,0.177 10 false B BUS 3.073,4.083 4.594,4.531 1.521,0.448 10 false Air Conditioning Harness Assembly

CAUTION / NOTICE / HINT

HINT:

Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Operate the R/F (Recirculation/Fresh) switch.


e.

Enter the following menus: Body / Air Conditioner / Data List.


f.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Air Inlet Damper Actual Pulse No. 1 blower damper servo sub-assembly (air inlet) actual pulse Min.: 0
Max.: 255
RECIRCULATION: 7 (pulse)
FRESH: 28 (pulse)
-
Body Electrical > Air Conditioner > Data List
Tester Display
Air Inlet Damper Actual Pulse
50003 121 131
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Inlet Damper Targ Pulse No. 1 blower damper servo sub-assembly (air inlet) pulse Min.: 0, Max.: 255 Operates between 7 and 28 pulses
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Inlet Damper Targ Pulse
50004 121 27
OK:

Recirculation damper position changes in accordance with each control range.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

3.REPLACE NO. 1 BLOWER DAMPER SERVO MOTOR SUB-ASSEMBLY (AIR INLET)
3.REPLACE NO. 1 BLOWER DAMPER SERVO MOTOR SUB-ASSEMBLY (AIR INLET)
a.

Replace the No. 1 blower damper servo sub-assembly (air inlet).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1442 is output A
DTC B1442 is not output B



A

4.REPLACE AIR CONDITIONING HARNESS ASSEMBLY

B

END (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY WAS DEFECTIVE)

4.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
a.

Replace the air conditioning harness assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY

HINT:

Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1442 is output A
DTC B1442 is not output B



A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)