Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM19V0EQ _58 Vehicle Interior _014613 HEATING / AIR CONDITIONING _0074198 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1451  Compressor Solenoid Circuit  


DESCRIPTION

In this circuit, the compressor assembly with pulley (compressor solenoid) receives a refrigerant compression demand signal from the air conditioning amplifier assembly.

Based on this signal, the compressor assembly with pulley (compressor solenoid) changes the amount of compressor output.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1451 Compressor Solenoid Circuit Open or short in compressor solenoid circuit
·

Compressor assembly with pulley (compressor solenoid)

·

Harness or connector between air conditioning amplifier assembly and compressor assembly with pulley (compressor solenoid)

·

Air conditioning amplifier assembly


-

WIRING DIAGRAM

E229254
5.01,0.792 5.104,0.969 0.094,0.177 10 false 2 3.833,0.792 3.927,0.969 0.094,0.177 10 false 2 2.448,0.792 2.542,0.969 0.094,0.177 10 false 1 5.229,0.885 5.688,1.063 0.458,0.177 10 false SOL+ 3.385,0.792 3.76,0.969 0.375,0.177 10 false SOL+ 2.625,0.792 2.969,0.969 0.344,0.177 10 false SOL- 4.823,3.5 5.167,3.677 0.344,0.177 10 false I77 4.823,3.667 6.385,4.125 1.563,0.458 10 false Air Conditioning Amplifier Assembly 2.25,1.49 4.365,1.917 2.115,0.427 10 false Compressor Assembly with Pulley (Compressor Solenoid) 2.25,1.333 2.74,1.583 0.49,0.25 10 false E74

PROCEDURE

1.INSPECT COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID)
a.
E229635
2.49,1.677 2.927,1.969 0.438,0.292 1.448,1.99 1.188,2.521 false 1.979,1.969 2.281,2.479 false 0.156,0.177 0.385,0.458 0.229,0.281 10 false *a 2.594,1.75 2.938,1.927 0.344,0.177 10 false E74 2.167,2.531 2.563,2.75 0.396,0.219 10 false SOL- 0.938,2.552 1.354,2.75 0.417,0.198 10 false SOL+
*a Component without harness connected
(Compressor Assembly with Pulley (Compressor Solenoid))


Disconnect the E74 compressor assembly with pulley (compressor solenoid) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E74-2 (SOL+) - E74-1 (SOL-) 20°C (68°F) 10 to 11 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - BODY GROUND)

NG

REPLACE COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID)

2.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E74-1 (SOL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the I77 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I77-2 (SOL+) - E74-2 (SOL+) Always Below 1 Ω
I77-2 (SOL+) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY