Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2011.10–2015.04
RM19V0EQ _59 Vehicle Exterior _014618 DOOR / HATCH _0074231 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284C 3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B277180

Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.


Hide 67492A 4.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B277182

Disengage the 3 clips and remove the front door lower frame bracket garnish.


Hide 5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.
B277183

Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.


b.

Disconnect each connector and remove the power window regulator master switch assembly with front door armrest base panel.


Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.
B281683

Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.


b.

Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel.


Hide 74220 7.REMOVE FRONT ARMREST ASSEMBLY

a.
B277187

Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.


Hide 81911B 8.REMOVE FRONT REFLEX REFLECTOR ASSEMBLY

a.
B293479C01
2.063,1.271 2.063,1.771 false 2.094,3.74 2.094,4.24 false 1.969,1.781 2.156,1.979 0.188,0.198 10 false *1 2,4.25 2.188,4.448 0.188,0.198 10 false *1 0.156,0.094 0.417,0.323 0.26,0.229 12 false *A 0.156,2.396 0.417,2.625 0.26,0.229 12 false *B
*A for LH Side
*B for RH Side
*1 Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the claw.


b.

Disconnect the connector and remove the front reflex reflector assembly.


Hide 67602 9.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B280589C03
1.216,0.494 1.368,0.653 0.151,0.159 10 *1 1.385,0.54 1.605,0.434 false
*1 Protective Tape


Put protective tape around the front door panel.


b.
B277189

Remove the 3 screws.


c.

Using a clip remover, disengage the 10 clips.


d.
B277190C03
0.938,4.229 0.688,4.229 false 1.604,0.729 1.094,1.01 false 0.531,4.135 0.688,4.302 0.156,0.167 10 false *1 0.938,0.927 1.115,1.094 0.177,0.167 10 false *2
*1 Reference Boss
*2 Front Door Inner Glass Weatherstrip


Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.


e.

Disengage the reference boss from the front door panel.


f.

Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.


g.
B277192

Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.


Hide 69206B 10.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B277194

Disengage the 2 claws and guides, and remove the front door inside handle sub-assembly.


Hide 68172A 11.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

a.
B277195C08
3.063,1 3.01,0.885 false 2.99,1 3.167,1.167 0.177,0.167 10 false *1
*1 Screwdriver


Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.


Hide 84927 12.REMOVE SEAT MEMORY SWITCH (w/ Memory)

Hide 86160 13.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 14.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

Hide 89430 15.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


Hide 67832 16.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B298356

Disconnect each connector.


b.

Disengage the 3 clamps.


c.

Remove the front door service hole cover.

HINT:

Remove any remaining butyl tape from the door.



Hide 68102 17.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

a.
B281733

Remove the grommet.


b.

Connect the cable to the negative (-) battery terminal.


c.

Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


d.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



e.

Disconnect the power window regulator master switch assembly.


f.
B280340

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the door glass to fall.



g.
B280342E01
0.558,0.166 0.753,0.354 0.195,0.188 10 (1) 1.356,0.069 1.551,0.257 0.195,0.188 10 (2)

Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

NOTICE:

Do not damage the door glass.



Hide 18.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.
B281734C07
1.167,0.146 1.896,0.813 false 1.01,0.042 1.333,0.292 0.323,0.25 10 false *1
*1 Temporary Bolt


Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.



b.

Remove the 5 bolts.


c.

Remove the front door window regulator assembly.


d.

Remove the temporary bolt from the front door window regulator assembly.


Hide 85720D 19.REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B280344

Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.


Hide 67924 20.REMOVE NO. 2 FRONT DOOR STIFFENER CUSHION

a.
B281687C05
1.185,1.225 1.372,1.412 0.187,0.187 10 *1 2.315,1.298 1.361,1.32 false
*1 Double-sided Tape


Remove the 2 bolts.


b.

Disengage the 2 guides and remove the No. 2 front door stiffener cushion.


Hide 68151C 21.REMOVE FRONT DOOR GLASS RUN

a.
B281735

Remove the front door glass run.


Hide 67402F 22.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B280347

Remove the 2 bolts.


b.

Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration.


Hide 67404F 23.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B280349

Remove the 2 bolts.


b.

Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.


Hide 24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B280351

Remove the hole plug.


b.
B280352

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Front Passenger Side)

a.

w/ Front Door Lock Cylinder:

HINT:

Use the same procedure for front passenger side and driver side.



Hide 69217F 26.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B280353

Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration.


Hide 69250B 27.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.

w/ Front Door Lock Cylinder:

HINT:

Use the same procedure for the front passenger side and the driver side.



b.

w/o Front Door Lock Cylinder:

i.
B280630

Remove the hole plug.


ii.
B280355

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.




Hide 69220 28.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.

w/ Smart Entry and Start System:

i.

Disengage the 2 claws.


ii.
B280356

Using a screwdriver, disconnect the connector.



b.
B280357

Remove the front door outside handle assembly as shown in the illustration.


Hide 69241H 29.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B280359

Disengage the 3 claws and remove the front door front outside handle pad.


Hide 69242E 30.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B280360

Disengage the 2 claws and remove the front door rear outside handle pad.


Hide 69040A 31.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

a.
B280361C13
2.969,2.625 3.135,2.74 false 3.146,2.646 3.302,2.802 0.156,0.156 10 false *1
*1 Front Door Lock Open Rod


Using a T30 "TORX" socket wrench, remove the 3 screws.


b.

Slide the front door lock with motor assembly downward, and remove the front door lock with motor assembly and cables as a unit.


c.

When reusing the front door lock with motor assembly:

i.
B280363

Remove the door lock wiring harness seal from the front door lock with motor assembly.



Hide 69720B 32.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B280364

Remove the front door lock remote control cable assembly.


Hide 69760C 33.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B280366

Using a screwdriver, disengage the 3 claws.


b.
B280367

Remove the front door inside locking cable assembly.


Hide 69202A 34.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

w/ Smart Entry and Start System:

i.
B280369

Disconnect the connector.


ii.

Disengage the 3 clamps.



b.
B280370C07
0.365,1.844 0.698,1.708 false 0.188,1.781 0.479,2.031 0.292,0.25 10 false *1 0.083,0.104 0.521,0.417 0.438,0.313 10 false *a 0.083,2.167 0.531,2.521 0.448,0.354 10 false *b
*1 Door Handle Nut
*a Outside
*b Inside


Using a T30 "TORX" socket wrench, remove the screw and door handle nut.


c.

Slide the front door outside handle frame sub-assembly to disengage the claw of the front door outside handle frame sub-assembly, and then remove it.


Hide 82186B 35.REMOVE FRONT DOOR WIRE (w/ Smart Entry and Start System)

a.
B280372

Disengage the 3 clamps and remove the front door wire.


Hide 69312 36.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B280374E01
2.052,0.552 2.542,0.948 0.49,0.396 10 false (1) 2.813,0.635 3.167,0.948 0.354,0.313 10 false (2)

Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 68620 37.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B280375

Remove the 3 bolts and front door check assembly.


Hide 67862 38.REMOVE FRONT DOOR WEATHERSTRIP

a.
B281736

Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.


Hide 67664C 39.REMOVE DOOR FRAME GARNISH

a.
B277197

Disengage the clip and remove the door frame garnish.

HINT:

This garnish needs to be replaced with a new one because the clip will break when removing it.



Hide 67864B 40.REMOVE FRONT DOOR NO. 2 WEATHERSTRIP

a.
B281737

Using a clip remover, disengage the 8 clips and remove the front door No. 2 weatherstrip.


Hide 67001A 41.REMOVE FRONT DOOR PANEL CUSHION

a.
B281738

Disengage the 2 claws and remove the 2 front door panel cushions.


Hide 67481C 42.REMOVE DOOR DUST PROOF SEAL

a.
B280379

Remove the door dust proof seal.


Hide 75720 43.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Hide 75756C 44.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

Hide 75754A 45.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 75976G 47.REMOVE FRONT DOOR LOWER OUTSIDE STRIPE