Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › 2011.10–2013.07
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


MONITOR DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).

(a) Vehicle speed is 20 km/h (12.43 mph) or more.

(b) Engine speed is 1000 rpm or higher.

(c) STA signal is on.


·

Park/Neutral position switch assembly*1

·

Starter relay (ST) circuit

·

ECM


Comes on DTC stored

*1: for Automatic Transaxle models.

MONITOR STRATEGY

Required Sensors/Components (Main) Starter relay (ST)
Park/Neutral position switch assembly
Ignition or starter switch assembly
Certification ECU (smart key ECU assembly)
Required Sensors/Components (Related) Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or higher

TYPICAL MALFUNCTION THRESHOLDS

Starter On

CONFIRMATION DRIVING PATTERN

A231469E24
1.229,1.979 1.656,2.198 0.427,0.219 10 Idling 0.396,2.26 1.604,2.583 1.208,0.323 10 Ignition Switch ON 1.063,0.865 1.635,1.073 0.573,0.208 10 24 km/h 2.396,2.854 3.083,3.167 0.688,0.313 10 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 20 seconds or more 2.01,2.333 2.302,2.552 0.292,0.219 10 [A] 2.615,2.125 2.823,2.302 0.208,0.177 10 [B] 4.063,0.458 4.292,0.625 0.229,0.167 10 [C] 4.885,3.333 5.115,3.5 0.229,0.167 10 [D]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds or more [B].

8.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0617.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again, if necessary, extend the driving time.




WIRING DIAGRAM

A266353E12
5.688,3.667 6.063,3.844 0.375,0.177 10 false STA 5.396,3.594 5.583,3.75 0.188,0.156 10 false 22 5.344,3.781 5.615,3.938 0.271,0.156 10 false A25 5.688,0.646 6.063,0.823 0.375,0.177 10 false NEO 5.396,0.594 5.583,0.75 0.188,0.156 10 false 45 5.344,0.781 5.615,0.938 0.271,0.156 10 false A25 5.688,1.406 6.063,1.583 0.375,0.177 10 false NSW 5.396,1.406 5.583,1.563 0.188,0.156 10 false 63 5.344,1.594 5.615,1.75 0.271,0.156 10 false E26 6.073,4.948 6.417,5.115 0.344,0.167 10 false ECM 3.542,2.25 3.646,2.406 0.104,0.156 10 false 9 3.708,2.25 3.813,2.406 0.104,0.156 10 false L 4.375,2.25 4.49,2.406 0.115,0.156 10 false B 4.563,2.25 4.688,2.406 0.125,0.156 10 false 4 3.313,2.563 3.594,2.719 0.281,0.156 10 false E4 3.313,2.729 5.094,3.063 1.781,0.333 10 false Park/Neutral Position Switch Assembly 0.094,0.115 2.667,0.375 2.573,0.26 12 false w/ Smart Entry and Start System: 0.594,3.781 1.125,3.938 0.531,0.156 10 false ST/AM2 1.438,0.781 1.729,0.969 0.292,0.188 10 false NE 1.781,0.667 2.042,0.823 0.26,0.156 10 false 16 1.281,1.583 1.667,1.74 0.385,0.156 10 false STAR 1.781,1.49 1.906,1.646 0.125,0.156 10 false 5 1.375,2.104 1.667,2.26 0.292,0.156 10 false STA 1.781,2 1.906,2.156 0.125,0.156 10 false 7 0.146,2.51 0.458,2.677 0.313,0.167 10 false A43 0.146,2.677 1.958,3.083 1.813,0.406 10 false Certification ECU (Smart key ECU Assembly) 3.271,4.594 3.5,4.75 0.229,0.156 10 false ST 3.01,4.135 3.135,4.292 0.125,0.156 10 false 2 3.01,5.042 3.135,5.198 0.125,0.156 10 false 1 2.573,4.135 2.667,4.292 0.094,0.156 10 false 5 2.573,5.031 2.667,5.188 0.094,0.156 10 false 3 1.792,5.51 2,5.667 0.208,0.156 10 false E9 1.75,5.333 1.844,5.49 0.094,0.156 10 false 1 1.115,5.719 1.24,5.885 0.125,0.167 10 false 1 1.073,5.917 1.292,6.073 0.219,0.156 10 false F2 1.51,6.708 2.156,7.229 0.646,0.521 10 false Starter Assembly 0.74,6.813 1.219,6.979 0.479,0.167 10 false Battery 0.594,4.792 1.219,4.948 0.625,0.156 10 false FL MAIN

A266092E02
5.698,1.115 6.219,1.302 0.521,0.188 10 false NSW*1 5.719,3.458 6.094,3.635 0.375,0.177 10 false STA 5.406,1.104 5.615,1.271 0.208,0.167 10 false 63 5.344,1.281 5.667,1.49 0.323,0.208 10 false E26 5.396,3.375 5.583,3.531 0.188,0.156 10 false 22 5.354,3.552 5.625,3.708 0.271,0.156 10 false A25 6.115,4.719 6.5,4.927 0.385,0.208 10 false ECM 3.385,2.417 3.667,2.573 0.281,0.156 10 false E4 3.385,2.583 5.167,2.917 1.781,0.333 10 false Park/Neutral Position Switch Assembly 0.073,0.063 2.667,0.25 2.594,0.188 12 false w/o Smart Entry and Start System: 1.354,1.167 1.479,1.323 0.125,0.156 10 false 4 1.531,1.167 1.854,1.375 0.323,0.208 10 false AM1 1.094,2.865 1.479,3.052 0.385,0.188 10 false AM1 1.104,3.688 1.427,3.875 0.323,0.188 10 false ALT 2.115,1.156 2.385,1.333 0.271,0.177 10 false ST1 2.458,1.167 2.583,1.323 0.125,0.156 10 false 3 1.354,1.604 1.479,1.76 0.125,0.156 10 false 5 1.531,1.604 1.854,1.781 0.323,0.177 10 false AM2 0.563,2.781 0.875,3.115 0.313,0.333 10 false ST/ AM2 2.115,1.604 2.396,1.76 0.281,0.156 10 false ST2 2.458,1.604 2.583,1.76 0.125,0.156 10 false 7 1.542,2.052 1.854,2.219 0.313,0.167 10 false I36 1.542,2.208 2.427,2.781 0.885,0.573 10 false Ignition or Starter Switch Assembly 3.26,4.375 3.49,4.531 0.229,0.156 10 false ST 3,3.917 3.125,4.073 0.125,0.156 10 false 2 3,4.823 3.125,4.979 0.125,0.156 10 false 1 2.573,3.917 2.698,4.073 0.125,0.156 10 false 5 2.573,4.823 2.698,4.979 0.125,0.156 10 false 3 1.781,5.292 1.99,5.448 0.208,0.156 10 false E9 1.75,5.094 1.875,5.26 0.125,0.167 10 false 1 1.115,5.51 1.24,5.677 0.125,0.167 10 false 1 1.073,5.698 1.292,5.854 0.219,0.156 10 false F2 1.479,6.49 2.115,6.854 0.635,0.365 10 false Starter Assembly 0.729,6.604 1.24,6.865 0.51,0.26 10 false Battery 4.563,2.042 4.688,2.198 0.125,0.156 10 false 4 4.375,2.042 4.521,2.24 0.146,0.198 10 false B 3.552,2.042 3.688,2.219 0.135,0.177 10 false 9 3.708,2.042 3.844,2.219 0.135,0.177 10 false L 5.115,1.188 5.292,1.375 0.177,0.188 10 false *1 4.135,1.188 4.313,1.375 0.177,0.188 10 false *1 3.083,1.688 3.229,1.844 0.146,0.156 10 false *2 3.313,2.031 3.5,2.208 0.188,0.177 10 false *1 5.073,2.063 5.281,2.24 0.208,0.177 10 false *1 4.094,6.958 6.156,7.167 2.063,0.208 10 false *2: for Manual Transaxle models 4.094,6.542 6.344,6.729 2.25,0.188 10 false *1: for Automatic Transaxle models 0.594,4.917 1.208,5.115 0.615,0.198 10 false FL MAIN

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the tester when the vehicle is driven at 20 km/h (12.4 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result:
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more Close (Starter signal off) A
Open (Starter signal on)
(for Automatic Transaxle models)
B
Open (Starter signal on)
(for Manual Transaxle models)
C




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/ smart entry and start system) A
OK (w/o smart entry and start system) B
NG C



A

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

B

5.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

C

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (certification ECU (smart key ECU assembly) - park/neutral position switch assembly - ST relay - ECM).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0617 is output A
DTC is not output B




A

B

END

5.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (park/neutral position switch assembly - ST relay - ECM).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
6.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (ignition or starter switch assembly - ST relay - ECM).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)