Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074095 PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function) J

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)  Guide Lines and Buttons are not Displayed for All Display Modes  


DESCRIPTION

The navigation ECU sub-assembly receives luggage compartment door lock assembly open/close signals from the main body ECU (multiplex network body ECU) via CAN communication. When the luggage compartment door is open, the camera aiming cannot be adjusted correctly because the rear television camera assembly is installed on the luggage compartment door. Therefore, when adjusting the camera aiming calibration while the back door is open, a back door open warning message will be displayed on the screen and camera aiming adjustment will be canceled.

HINT:
·

Check the parking assist monitor screen display mode settings. (Check if the parking guide lines are set to off.)

·

The luggage compartment door lock assembly is connected to the main body ECU (multiplex network body ECU) by the vehicle wire harness.



WIRING DIAGRAM

E224384E12
2.667,1.438 2.792,1.583 0.125,0.146 10 false 2 0.302,1.438 0.406,1.583 0.104,0.146 10 false 3 0.177,1.833 0.521,1.979 0.344,0.146 10 false T3 0.188,1.979 3.063,2.365 2.875,0.385 10 false Luggage Compartment Door Lock Assembly 3.229,0.438 3.594,0.583 0.365,0.146 10 false MB 3.542,0.854 5.177,1.385 1.635,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 5.802,0.865 6.802,1.354 1,0.49 10 false Navigation ECU Sub-assembly 0.635,0.25 0.813,0.396 0.177,0.146 10 false 9 3.615,0.438 4.042,0.635 0.427,0.198 10 false LGCY 0.844,2.396 2.802,2.583 1.958,0.188 10 false : CAN Communication Line 2.469,1.438 2.646,1.583 0.177,0.146 10 false E 0.469,1.438 0.76,1.583 0.292,0.146 10 false D+ 0.594,0.438 0.958,0.583 0.365,0.146 10 false 3C 3.302,0.24 3.479,0.385 0.177,0.146 10 false 4 0.646,0.729 3.344,1.104 2.698,0.375 10 false Instrument Panel Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)>CALIBRATION



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Luggage Courtesy SW Luggage courtesy switch signal ON or OFF ON: Luggage compartment door open
OFF: Luggage compartment door closed
-
Body Electrical > Main Body > Data List
Tester Display
Luggage Courtesy SW
50003 123 53
OK:

The luggage compartment door courtesy switch functions as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
2.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
a.
B279065C11
2.385,2.198 2.188,2.438 false 2.542,2.198 2.542,2.552 false 0.26,0.198 0.5,0.427 0.24,0.229 10 false *a 0.583,0.979 0.823,1.208 0.24,0.229 10 false *b 1.667,0.99 1.906,1.219 0.24,0.229 10 false *c 2.5,2.573 2.885,2.906 0.385,0.333 10 false E 2.083,2.438 2.521,2.813 0.438,0.375 10 false D+
*a Component without harness connected
(Luggage Compartment Door Lock Assembly)
*b Close (Lock)
*c Open (Unlock)


Check operation of the door courtesy switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Measurement Condition Switch Condition Specified Condition
2 (E) - 3 (D+) Close (Lock) 10 kΩ or higher
2 (E) - 3 (D+) Open (Unlock) Below 1 Ω




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the T3 luggage compartment door lock assembly connector.


b.

Disconnect the 3C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T3-3 (D+) - 3C-9 Always Below 1 Ω
T3-3 (D+) - Body ground Always 10 kΩ or higher
T3-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E173023C16
1.118,0.292 1.433,0.502 0.315,0.21 1.198,0.324 1.456,0.531 0.258,0.207 10 3C 4.738,0.399 5.053,0.609 0.315,0.21 4.789,0.432 5.047,0.639 0.258,0.207 10 MB 3.48,1.52 3.919,1.679 0.439,0.158 10 LGCY 3.373,1.009 3.536,1.499 false 0.128,0.077 0.312,0.265 0.184,0.189 10 *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3C-9 - MB-4 (LGCY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY