This DTC is stored when LIN communication between the power window regulator motor assembly (for driver side) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2321 | Driver Side Door ECU Communication Stop | No communication between power window regulator motor assembly (for driver side) and main body ECU (multiplex network body ECU) for 10 seconds or more. | ·
Power window regulator motor assembly (for driver side) ·
Main body ECU (multiplex network body ECU) ·
Wire harness or connector ·
Instrument Panel junction block assembly ·
DOOR No. 2 fuse |
Inspect the fuses for circuits related to this system before performing the following procedure.
When the power window regulator motor assembly (for driver side) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
When using the intelligent tester to troubleshoot with the ignition switch off:
Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Disconnect the 3B instrument panel junction block assembly connector.
Disconnect the K9*1, J9*2 power window regulator motor (for driver side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-30 (LIN2) - K9-9 (LIN)*1
3B-30 (LIN2) - J9-9 (LIN)*2 |
Always | Below 1 Ω |
| 3B-30 (LIN2) - Body ground | Always | 10 kΩ or higher |
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
*b | Component without harness connected
(Instrument Panel Junction Block Assembly) |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-30 (LIN2) - MB-16 (LIN2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K9-2 (B)*1 - Body ground
J9-2 (B)*2 - Body ground |
Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K9-1 (E)*1 - Body ground
J9-1 (E)*2 - Body ground |
Always | Below 1 Ω |
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power window regulator motor assembly (for driver side).
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTC.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
DTC B2321 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG