Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0076198 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2757  Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)  


SYSTEM DESCRIPTION

The ECM uses the signals from the throttle position sensor, air-flow meter, turbine (input) speed sensor, output speed sensor and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.

C133226E01
0.273,1.817 0.765,1.980 0.492,0.163 10 Sleeve 2.273,0.404 3.131,0.592 0.858,0.188 10 Spool Valve 2.771,2.128 3.653,2.315 0.882,0.188 10 Solenoid Coil 5.36,2.137 5.937,2.312 0.577,0.175 10 Current 3.754,0.233 4.397,0.567 0.644,0.334 10 Hydraulic Pressure 1.309,1.515 0.896,1.897 0.896,1.897 0.761,1.897 false 2.238,0.476 2.152,0.476 2.152,0.476 1.915,1.298 false 2.753,1.537 3.148,2.015 3.148,2.015 3.148,2.124 false

The ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect shift solenoid valve SLU, valve body and torque converter mechanical problems.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)
·

Lock-up does not occur when requested.

·

Lock-up occurs when shift solenoid valve SLU is requested to turn on in the lock-up range.


(2-trip detection logic)
·

Shift solenoid valve SLU remains open or closed

·

Valve body is blocked

·

Torque converter assembly

·

Automatic transaxle (clutch, brake or gear, etc.)

·

Line pressure is too low


Comes on DTC stored

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on the turbine (input) speed sensor NT, output speed sensor NC, engine speed, engine load, engine temperature, vehicle speed, transmission fluid temperature, and gear selection. The ECM determines the lock-up status of the torque converter by comparing the engine speed (NE) to the input turbine speed (NT). The ECM calculates the actual transmission gear by comparing input turbine speed (NT) to output shaft speed (NC). When conditions are appropriate, the ECM requests "lock-up" by applying control voltage to shift solenoid SLU. When SLU is turned on, it applies pressure to the lock-up relay valve and locks the torque converter.

If the ECM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the ECM interprets this as a fault in shift solenoid valve SLU or lock-up system performance.

The ECM will turn on the MIL and store the DTC.

Example:

When any of the following is met, the system judges it as a malfunction.

·

There is a difference in rotation (speed) between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up.

(Engine speed is at least 70 rpm greater than input turbine speed.)


CAUTION / NOTICE / HINT

HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


ACTIVE TEST


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the intelligent tester, perform the Active Test.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Lock Up Controls the shift solenoid SLU and SL to set the automatic transaxle to the lock-up condition. ON/OFF Can be used to check SLU and SL solenoid operation.
[Vehicle Condition]
·

Throttle valve opening angle: Less than 20%

·

Vehicle speed:60 km/h (37 mph) or more, and 6th gear


Powertrain > Engine and ECT > Active Test
Tester Display
Activate the Lock Up
50004 234 115
HINT:

This test can be conducted when the vehicle speed is 60 km/h (37 mph) or more.




h.

Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

HINT:
·

When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.

·

Slowly release, but not fully, the accelerator pedal in order to decelerate. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off.)



C159073E10
4.531,2.188 5.542,1.958 5.542,1.958 5.604,1.958 false 5.125,2.24 5.542,2.583 5.542,2.583 5.604,2.583 false 0.719,2.677 1.646,2.875 0.927,0.198 10 Engine Speed 0.719,1.677 1.906,2.094 1.188,0.417 10 Accelerator Pedal Fully Released 0.719,1.021 1.906,1.438 1.188,0.417 10 Accelerator Pedal Opening Angle 4.99,3.125 5.438,3.323 0.448,0.198 10 Time 5.656,1.865 6.615,2.063 0.958,0.198 10 Lock-up OFF 5.656,2.49 6.615,2.688 0.958,0.198 10 Lock-up ON



PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2757)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 234

e.

Read the DTCs using the intelligent tester.

Result:
Display (DTC output) Proceed to
Only "P2757" is output A
"P2757" and other DTCs are output B


HINT:

If any other codes besides "P2757" are output, perform troubleshooting for those DTCs first.




A

2.INSPECT SHIFT SOLENOID VALVE SLU

B

2.INSPECT SHIFT SOLENOID VALVE SLU
a.
C201747C02
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 0.49,0.521 0.667,0.719 0.177,0.198 10 1 2.531,0.5 2.708,0.698 0.177,0.198 10 2 1.177,4.198 1.385,4.406 0.208,0.208 10 (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 (+) 0.51,2.771 0.688,2.969 0.177,0.198 10 1 2.521,2.76 2.698,2.958 0.177,0.198 10 2 0.135,0.135 0.354,0.344 0.219,0.208 10 *1
*1 Shift Solenoid Valve SLU


Remove shift solenoid valve SLU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>REMOVAL


OK:

There are no foreign objects on each valve and they operate smoothly.


Result:
Proceed to
OK
NG



OK

4.INSPECT TORQUE CONVERTER ASSEMBLY

NG

4.INSPECT TORQUE CONVERTER ASSEMBLY

OK:

The torque converter assembly operates normally.


Result:
Proceed to
OK
NG



OK

NG