Each speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. These signals are used by the ABS control system.
The speed sensor rotors have rows of alternating N and S magnetic poles. Hall IC type speed sensors use the frequency of output pulses to detect the vehicle speed. Because the sensor outputs digital pulses, it can detect the vehicle speed even when the vehicle is nearly stationary.
DTCs C1273 and C1274 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1273 and C1274 are output only in Test Mode.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1273 | Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) | Detected only during Test Mode. | ·
Rear speed sensor RH/LH ·
Sensor installation ·
Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) |
| C1274 | Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) | Detected only during Test Mode. | ·
Rear speed sensor RH/LH ·
Sensor installation ·
Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) |
| C1332 | Open in Rear Speed Sensor RH | An open or short in the speed sensor signal circuit. | ·
Rear speed sensor RH/LH ·
Speed sensor circuit ·
Sensor installation |
| C1333 | Open in Rear Speed Sensor LH | An open or short in the speed sensor signal circuit. | ·
Rear speed sensor RH/LH ·
Speed sensor circuit ·
Sensor installation |
| C1466 | Rear Speed Sensor RH | Any of the following is detected:
1.
The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds. 2.
After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected. 3.
After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected. 4.
The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions): ·
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) ·
The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.) ·
The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) 5.
Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less. 6.
An abnormal signal is received from a wheel speed sensor. |
·
Rear speed sensor RH/LH ·
Speed sensor circuit ·
Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) ·
Sensor installation ·
Skid control ECU (Brake actuator assembly) |
| C1467 | Rear Speed Sensor LH | Any of the following is detected:
1.
The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds. 2.
After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected. 3.
After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected. 4.
The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions): ·
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) ·
The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.) ·
The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) 5.
Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less. 6.
An abnormal signal is received from a wheel speed sensor. |
·
Rear speed sensor RH/LH ·
Speed sensor circuit ·
Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) ·
Sensor installation ·
Skid control ECU (Brake actuator assembly) |
DTCs C1273, C1332 and C1466 are for the rear speed sensor RH.
DTCs C1274, C1333 and C1467 are for the rear speed sensor LH.
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List using the intelligent tester.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| RR Wheel Speed |
| RL Wheel Speed |
Check the speed value output from the speed sensor displayed on the intelligent tester.
Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
The speed value output from the speed sensor displayed on the intelligent tester is similar to the speed indicated on the speedometer.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Perform the sensor check using the Test Mode procedure.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE
| Tester Display |
|---|
| Signal Check |
All Test Mode DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs C1332, C1333, C1466 and C1467 are not output. | A |
| DTCs C1332, C1333, C1466 and/or C1467 are output. | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *1 | Rear Speed Sensor |
Turn the ignition switch off.
Check the speed sensor installation.
There is no clearance between the sensor and rear axle carrier.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH |
| *B | for LH |
| *a | Front view of skid control sensor wire |
| *b | Front view of wire harness connector
(to Sensor Side Connector) |
| *c | Front view of wire harness connector
(to Vehicle Side Connector) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Remove the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h1-2 (RR+) - hO1-1 (RR+) | Always | Below 1 Ω |
| h1-2 (RR+) - hO1-2 (RR-) | Always | 10 kΩ or higher |
| h1-2 (RR+) - Body ground | Always | 10 kΩ or higher |
| h1-1 (RR-) - hO1-2 (RR-) | Always | Below 1 Ω |
| h1-1 (RR-) - hO1-1 (RR+) | Always | 10 kΩ or higher |
| h1-1 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| i1-2 (RL+) - iN1-1 (RL+) | Always | Below 1 Ω |
| i1-2 (RL+) - iN1-2 (RL-) | Always | 10 kΩ or higher |
| i1-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| i1-1 (RL-) - iN1-2 (RL-) | Always | Below 1 Ω |
| i1-1 (RL-) - iN1-1 (RL+) | Always | 10 kΩ or higher |
| i1-1 (RL-) - Body ground | Always | 10 kΩ or higher |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A49 skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-17 (RR+) - hO1-1 (RR+) | Always | Below 1 Ω |
| A49-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A49-29 (RR-) - hO1-2 (RR-) | Always | Below 1 Ω |
| A49-29 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-31 (RL+) - iN1-1 (RL+) | Always | Below 1 Ω |
| A49-31 (RL+) - Body ground | Always | 10 kΩ or higher |
| A49-18 (RL-) - iN1-2 (RL-) | Always | Below 1 Ω |
| A49-18 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the skid control sensor wire.
Reconnect the A49 skid control ECU connector.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs C1332, C1333, C1466 and/or C1467 are output. | A |
| DTCs C1332, C1333, C1466 and C1467 are not output. | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs C1332, C1333, C1466 and C1467 are not output. | A |
| DTCs C1332, C1333, C1466 and/or C1467 are output. | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE
A
B