Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2015.04
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076219 VEHICLE STABILITY CONTROL SYSTEM S

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  DIAGNOSTIC TROUBLE CODE CHART  


Vehicle Stability Control System
DTC No. Detection Item DTC Detection Condition Trouble Area Link
C1201 Engine Control System Malfunction Engine control system malfunction signal continues for 2.5 seconds. SFI system Click here
C1224 NE Signal The vehicle speed is 6 km/h (4 mph) or more, the +BS terminal voltage is between 9.6 and 16.5 V, and the engine speed signal is more than 12800 rpm for 2.5 seconds or more.
·

CAN communication system

·

ECM


Click here
C1225 SM Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C1226 SA2 Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C1227 SA3 Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C1228 STR Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C1234 Yaw Rate Sensor Any of the following is detected:
1.

The yaw rate sensor offset value is estimated as less than -5.25 deg/s or more than 5.25 deg/s based on offset correction performed when the vehicle is stopped and then the vehicle starts off.

2.

The offset correction did not complete with the vehicle stopped, and the yaw rate sensor offset value is estimated as less than -15 deg/s or more than 15 deg/s based on the offset correction performed while the vehicle is being driven.

3.

The offset correction completed with the vehicle stopped and the yaw rate sensor offset value is less than -7.5 deg/s or more than 7.5 deg/s.

4.

The yaw rate sensor offset value is estimated as less than -7.5 deg/s or more than 7.5 deg/s based on the offset correction performed while the vehicle is being driven.

5.

After the VSC system has started, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 5 seconds or more when the vehicle is stopped.

6.

After the VSC system has started, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more when the vehicle starts off.

7.

After the VSC system has started, but before the vehicle has started off, as the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more.

8.

The yaw rate sensor value is less than -94.75 deg/s or more than 94.75 deg/s for 0.8 seconds or more.

9.

The change of the yaw rate sensor value within 0.04 seconds is abnormal.

10.

The value from the yaw rate sensor is judged as abnormal based on the skid control ECU estimation.


·

Sensor installation

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Yaw rate and acceleration sensor circuit


Click here
C1237 Speed Sensor Rotor Faulty Any of the following is detected:
1.

Discrepancy among four wheel speed sensor output.

2.

Abnormal pulse signals from 3 or more sensors.

3.

Continuous ABS control is performed for 60 seconds or more.

4.

VSC control is performed for 5 seconds or more.


·

Tire and wheel size

·

Tire deformation

·

Speed sensor rotor

·

Speed sensor

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)


Click here
C1241 Low Power Supply Voltage Malfunction Any of the following is detected:
1.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (soft low voltage) is less than 9.6 V for 1 second or more.

2.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (hard low voltage) is less than 6.9 V for 1 second or more.

3.

The vehicle speed is 15 km/h (9 mph) or more, the +BS terminal voltage is 9.6 V or more, the skid control ECU turns on more than one valve at the same time within a short period of time and the valve relay supply voltage drop exceeds the threshold. (The skid control ECU monitors the resistance of the power source line at the +BS terminal. A malfunction is detected when an abnormality occurs in the +BS terminal wire harness or its connection and the skid control ECU determines that the wiring resistance at the +BS terminal exceeds the standard resistance.)

4.

The +BS terminal voltage is less than 6.7 V and the skid control ECU judges that power supply voltage is abnormal for 0.06 seconds or more.


·

ABS NO. 2 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Ground circuit

·

Internal power supply circuit of the skid control ECU


Click here
C1246 Master Cylinder Pressure Sensor Malfunction Any of the following is detected:
1.

The voltage of the sensor signal is out of range (below 0.129 V, above 3.29 V).

2.

An abnormality is detected in the skid control ECU internal sensor test.

3.

The sensor signal offset value is out of range.


·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder pressure sensor (Brake actuator assembly)


Click here
C1249 Open in Stop Light Switch Circuit The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.09 kgf/cm2, 72 psi) or less, and the stop light switch is on for 60 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)


Click here
C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Sensor installation

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)


Click here
C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Sensor installation

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)


Click here
C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Sensor installation

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)


Click here
C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Sensor installation

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)


Click here
C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode. Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH) Click here
C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode. Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH) Click here
C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode. Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) Click here
C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode. Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) Click here
C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) Detected only during Test Mode.
·

Stop light switch assembly

·

Brake pedal load sensing switch (Brake pedal support assembly)

·

Brake booster assembly

·

Master cylinder pressure sensor (Brake actuator assembly)


Click here
C1288 Error in Matching of ECUs ECM does not match. ECM Click here
C1300 Skid Control ECU Malfunction Internal failure of the skid control ECU control unit. Skid control ECU (Brake actuator assembly) Click here
C1330 Open in Front Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


Click here
C1331 Open in Front Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


Click here
C1332 Open in Rear Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


Click here
C1333 Open in Rear Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


Click here
C1381 Acceleration Sensor Power Supply Voltage Malfunction Vehicle speed is 6 km/h (4 mph) and yaw rate and acceleration sensor power supply malfunction signal is received for 1.1 seconds or more.
·

Yaw rate and acceleration sensor power source circuit

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


Click here
C1417 High Power Supply Voltage Malfunction +BS terminal voltage is more than 16.5 V for 1 second or more.
·

ABS NO. 2 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU


Click here
C1419 Acceleration Sensor Internal Circuit With the +BS terminal voltage 9.6 to 16.5 V, the acceleration sensor malfunction signal is received from the acceleration sensor. Yaw rate and acceleration sensor (Airbag sensor assembly) Click here
C1420 Acceleration Sensor Malfunction Difference between the acceleration sensor value and the control value estimated inside the skid control ECU is abnormal.
·

Sensor installation

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


Click here
C1425 Open in Stop Light Switch Circuit An open in the stop light switch input line continues for 3 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)


Click here
C1426 Stop Light Switch OFF Stuck Malfunction Either of the following is detected:
1.

With the stop light switch off, the stop light switch is judged to be on based on the master cylinder pressure value for 3 seconds or more.

2.

With the stop light switch off, the master cylinder pressure is more than 8 MPa (81.6 kgf/cm2, 1160 psi) for 3 seconds or more.


·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Ground circuit

·

Skid control ECU (Brake actuator assembly)


Click here
C1428 Motor Circuit Malfunction A malfunction occurs in the pump motor circuit. Pump motor circuit Click here
C1429 Open or Short in Brake Pedal Load Sensing Switch An open or short in the brake pedal load sensing switch circuit continues for 0.5 seconds or more.
·

Brake pedal load sensing switch (Brake pedal support assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (Brake actuator assembly)


Click here
C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction Either of the following is detected:
1.

With the stop light switch on, the brake pedal load sensing switch off, and the master cylinder pressure more than 6 MPa (61.2 kgf/cm2, 870 psi), the vehicle acceleration rate is less than -4 m/s2 for 1 second or more.

2.

With the stop light switch on, the brake pedal load sensing switch off, and the master cylinder pressure more than 6 MPa (61.2 kgf/cm2, 870 psi), the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.


·

Brake pedal load sensing switch (Brake pedal support assembly)

·

Brake pedal load sensing switch circuit


Click here
C1431 Brake Pedal Load Sensing Switch ON Stuck Malfunction Either of the following is detected:
1.

With the stop light switch off, the brake pedal load sensing switch on, and the master cylinder pressure less than 0.7 MPa (7.13 kgf/cm2, 101 psi), the vehicle acceleration rate is more than -0.8 m/s2 for 10 seconds or more. (Only when the engine is running and booster malfunctions are not detected.)

2.

The condition that the brake pedal load sensing switch remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (19 mph) occurs 5 times in succession.


·

Brake pedal load sensing switch (Brake pedal support assembly)

·

Brake pedal load sensing switch circuit


Click here
C1432 Steering Angle Sensor Power Source Voltage Malfunction With the +BS terminal voltage 9.6 to 16.5 V, the steering angle sensor power supply circuit malfunction signal is received from the steering angle sensor.
·

Steering angle sensor power supply

·

Steering angle sensor


Click here
C1433 Steering Angle Sensor Internal Circuit With the +BS terminal voltage 9.6 to 16.5 V, the steering angle sensor malfunction signal is received from the steering angle sensor. Steering angle sensor Click here
C1434 Steering Angle Sensor Output Malfunction Any of the following is detected:
1.

The difference between zero point stored in the steering angle sensor and the estimated zero point exceeds 15 deg.

2.

The offset value of the steering angle sensor is -13.5 deg. or less or 13.5 deg. or more.

3.

The steering angle sensor value exceeds a specified value for 0.3 seconds or more.

4.

The change of the steering angle sensor value within 0.02 seconds is abnormal.

5.

The steering angle sensor value changes by less than 5 deg. and both left and right turns have been recognized.

6.

There is a difference between the skid control ECU estimated value and the steering angle sensor value due to an abnormal steering angle sensor value.


·

Sensor installation

·

Steering angle sensor power supply

·

Steering angle sensor

·

Skid control ECU (Brake actuator assembly)


Click here
C1435 Yaw Rate Sensor Internal Circuit With the +BS terminal voltage 9.6 to 16.5 V, the yaw rate sensor malfunction signal is received from the yaw rate sensor. Yaw rate and acceleration sensor (Airbag sensor assembly) Click here
C1436 Yaw Rate Sensor Malfunction Difference between the yaw rate sensor value and the control value estimated inside the skid control ECU is abnormal.
·

Sensor installation

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


Click here
C1439 Steering Angle Sensor Initialization Incomplete After the steering angle sensor zero point calibration at a speed of 15 km/h (9 mph) or more for 1 second or more is cleared due to, for example, fluctuations in the power source, the steering angle sensor zero point calibration cannot be obtained for 115 seconds of continuous driving.
·

Steering angle sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


Click here
C1445 Vehicle Driven with Steering Angle Sensor not Initialized Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record of steering angle sensor zero point calibration at a speed of 15 km/h (9 mph) or more for 115 seconds or more without the brake pedal being depressed.
·

Steering angle sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


Click here
C1464 Front Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)


·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


Click here
C1465 Front Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)


·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


Click here
C1466 Rear Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


Click here
C1467 Rear Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


Click here
C1468 SFR Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C1469 SFL Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C146A SRR Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C146B SRL Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C146C Open in ABS Motor Relay Circuit Any of the following is detected:
1.

When the ABS motor relay is actuated, voltage is not supplied to the pump motor.

2.

When the ABS motor relay is not actuated, voltage in the pump motor is high.

3.

The skid control ECU judges that pump motor operation is abnormal.


·

ABS NO. 1 fuse (Fusible link block assembly)

·

ABS motor relay circuit

·

ABS motor relay (Brake actuator assembly)


Click here
C146E Open in ABS Solenoid Relay Circuit Either of the following is detected:
1.

A solenoid relay drive circuit in the skid control ECU is malfunctioning.

2.

The solenoid relay cannot be switched between on and off.


·

ABS NO. 2 fuse (Fusible link block assembly)

·

ABS solenoid relay circuit

·

ABS solenoid relay (Brake actuator assembly)


Click here
C1472 Acceleration Sensor Any of the following is detected:
1.

With the vehicle stopped, the internal acceleration value is less than -7 m/s2 or more than 7 m/s2 for 0.4 seconds or more.

2.

The acceleration sensor offset value is estimated as less than -2.25 m/s2 or more than 2.25 m/s2 based on the offset correction performed while the vehicle is being driven.

3.

The acceleration sensor value is less than -14.6 m/s2 or more than 14.6 m/s2 for 0.8 seconds or more.


·

Sensor installation

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Yaw rate and acceleration sensor circuit


Click here
U0073 Control Module Communication Bus OFF The +BS terminal voltage is between 9.6 and 16.5 V and bus off is judged for 0.1 seconds or more. CAN communication system Click here
U0100 Lost Communication with ECM / PCM The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals cannot be sent to the ECM for 2.5 seconds or more.
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

ECM


Click here
U0123 Lost Communication with Yaw Rate Sensor Module The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the yaw rate and acceleration sensor cannot be received for 1.1 seconds or more.
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


Click here
U0126 Lost Communication with Steering Angle Sensor Module The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the steering angle sensor cannot be received for 1.1 seconds or more.
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

Steering angle sensor


Click here