Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076219 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  U0073  Control Module Communication Bus OFF  U0100  Lost Communication with ECM / PCM  U0123  Lost Communication with Yaw Rate Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  


DESCRIPTION

The skid control ECU receives signals from the ECM, steering angle sensor, and yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0073 Control Module Communication Bus OFF The +BS terminal voltage is between 9.6 and 16.5 V and bus off is judged for 0.1 seconds or more. CAN communication system
U0100 Lost Communication with ECM / PCM The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals cannot be sent to the ECM for 2.5 seconds or more.
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

ECM


U0123 Lost Communication with Yaw Rate Sensor Module The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the yaw rate and acceleration sensor cannot be received for 1.1 seconds or more.
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


U0126 Lost Communication with Steering Angle Sensor Module The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the steering angle sensor cannot be received for 1.1 seconds or more.
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

Steering angle sensor



WIRING DIAGRAM

C243536E06
0.823,0.979 1.51,1.344 0.688,0.365 10 false CANL 0.781,1.635 1.531,1.938 0.75,0.302 10 false CANH 0.781,3.76 1.458,4.063 0.677,0.302 10 false CANL 0.781,4.417 1.458,4.719 0.677,0.302 10 false CANH 2.479,0.708 2.677,0.854 0.198,0.146 10 false 2 2.458,1.417 2.698,1.615 0.24,0.198 10 false 1 2.771,2.083 3.052,2.313 0.281,0.229 10 false 2 4.313,2.083 4.625,2.333 0.313,0.25 10 false 1 4.594,0.75 4.948,1.01 0.354,0.26 10 false 2 4.594,1.417 4.823,1.604 0.229,0.188 10 false 1 1.271,0.854 1.542,1.073 0.271,0.219 10 false 26 1.271,1.531 1.594,1.74 0.323,0.208 10 false 13 5.49,2.021 5.76,2.177 0.271,0.156 10 false A49 6.031,0.938 6.604,1.281 0.573,0.344 10 false CANL 6.021,1.615 6.615,1.938 0.594,0.323 10 false CANH 5.771,0.844 6.115,1.094 0.344,0.25 10 false 14 5.771,1.521 6.104,1.813 0.333,0.292 10 false 26 5.49,2.177 7.021,2.656 1.531,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 5.625,4.99 7.104,5.177 1.479,0.188 10 false Steering Angle Sensor 6.031,3.74 6.635,3.99 0.604,0.25 10 false CANL 6.031,4.406 6.698,4.688 0.667,0.281 10 false CANH 5.844,3.625 5.948,3.781 0.104,0.156 10 false 2 5.844,4.281 5.958,4.438 0.115,0.156 10 false 3 1.26,4.302 1.719,4.594 0.458,0.292 10 false 13 1.26,3.646 1.76,3.969 0.5,0.323 10 false 22 3.271,2.271 3.927,2.771 0.656,0.5 10 false Junction Connector 0.104,4.833 0.531,5.094 0.427,0.26 10 false I47 2.771,3.281 3.01,3.521 0.24,0.24 10 false 2 4.281,3.271 4.542,3.469 0.26,0.198 10 false 1 5.625,4.823 6.042,5.125 0.417,0.302 10 false I29 0.104,4.99 2.271,5.458 2.167,0.469 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 4.594,3.531 4.906,3.802 0.313,0.271 10 false 2 4.594,4.156 4.771,4.313 0.177,0.156 10 false 1 2.458,3.51 2.635,3.667 0.177,0.156 10 false 2 2.458,4.198 2.688,4.479 0.229,0.281 10 false 1 0.615,2.281 1.156,2.604 0.542,0.323 10 false ECM 2.354,0.958 2.823,1.208 0.469,0.25 10 false I104 2.969,4.906 4.25,5.094 1.281,0.188 10 false Junction Connector 0.615,2.115 1.083,2.375 0.469,0.26 10 false A25 2.365,1.625 2.813,1.833 0.448,0.208 10 false I104 4.51,0.969 5,1.271 0.49,0.302 10 false I105 4.49,1.625 4.979,1.875 0.49,0.25 10 false I105 2.969,2.094 3.656,2.438 0.688,0.344 10 false I101 3.927,2.083 4.365,2.302 0.438,0.219 10 false I101 2.375,3.75 2.833,3.99 0.458,0.24 10 false I103 2.375,4.417 2.875,4.688 0.5,0.271 10 false I103 4.552,3.75 5.01,4.021 0.458,0.271 10 false I97 4.563,4.417 4.927,4.677 0.365,0.26 10 false I97 3.01,3.281 3.406,3.531 0.396,0.25 10 false I93 3.958,3.281 4.344,3.604 0.385,0.323 10 false I93 0.219,0.125 0.906,0.333 0.688,0.208 12 false for LHD:

C243537E05
0.781,0.958 1.198,1.198 0.417,0.24 10 false CANL 0.781,1.594 1.198,1.865 0.417,0.271 10 false CANH 0.781,3.771 1.198,4.094 0.417,0.323 10 false CANL 0.781,4.427 1.198,4.75 0.417,0.323 10 false CANH 2.458,0.75 2.656,0.896 0.198,0.146 10 false 2 2.448,1.406 2.646,1.542 0.198,0.135 10 false 1 2.771,2.094 2.969,2.417 0.198,0.323 10 false 2 4.313,2.094 4.583,2.417 0.271,0.323 10 false 1 4.594,0.76 4.781,0.917 0.188,0.156 10 false 2 4.583,1.417 4.708,1.573 0.125,0.156 10 false 1 1.271,0.813 1.479,1.01 0.208,0.198 10 false 2 1.271,1.479 1.469,1.719 0.198,0.24 10 false 3 5.5,2.021 5.823,2.313 0.323,0.292 10 false A49 6.031,0.958 6.5,1.115 0.469,0.156 10 false CANL 6.031,1.625 6.5,1.781 0.469,0.156 10 false CANH 5.781,0.854 6.01,1.104 0.229,0.25 10 false 14 5.781,1.521 6,1.76 0.219,0.24 10 false 26 5.5,2.177 7.125,2.802 1.625,0.625 10 false Skid Control ECU (Brake Actuator Assembly) 0.115,2.229 1.604,2.604 1.49,0.375 10 false Steering Angle Sensor 6.031,3.76 6.542,4.083 0.51,0.323 10 false CANL 6.031,4.427 6.531,4.781 0.5,0.354 10 false CANH 5.771,3.635 6.031,3.917 0.26,0.281 10 false 26 5.771,4.302 6.01,4.552 0.24,0.25 10 false 13 1.26,4.302 1.521,4.615 0.26,0.313 10 false 13 1.26,3.635 1.531,3.958 0.271,0.323 10 false 22 3.281,2.292 3.938,2.646 0.656,0.354 10 false Junction Connector 0.115,4.823 0.427,5.083 0.313,0.26 10 false I47 2.771,3.281 2.979,3.604 0.208,0.323 10 false 2 4.313,3.281 4.531,3.51 0.219,0.229 10 false 1 0.115,2.052 0.448,2.271 0.333,0.219 10 false I29 0.115,4.99 2.323,5.677 2.208,0.688 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 4.583,3.542 4.76,3.698 0.177,0.156 10 false 2 4.583,4.198 4.76,4.354 0.177,0.156 10 false 1 2.458,3.542 2.677,3.813 0.219,0.271 10 false 2 2.448,4.198 2.552,4.354 0.104,0.156 10 false 1 6.271,5.042 6.698,5.198 0.427,0.156 10 false ECM 2.406,0.958 2.75,1.115 0.344,0.156 10 false I97 2.969,4.917 4.313,5.375 1.344,0.458 10 false Junction Connector 6.271,4.885 6.563,5.042 0.292,0.156 10 false A25 2.406,1.625 2.75,1.781 0.344,0.156 10 false I97 4.51,0.958 4.917,1.313 0.406,0.354 10 false I105 4.51,1.625 4.938,1.958 0.427,0.333 10 false I105 2.969,2.083 3.313,2.24 0.344,0.156 10 false I101 3.917,2.083 4.292,2.385 0.375,0.302 10 false I101 2.375,3.74 2.823,4.031 0.448,0.292 10 false I103 2.375,4.406 2.792,4.74 0.417,0.333 10 false I103 4.49,3.76 4.958,4.052 0.469,0.292 10 false I104 4.51,4.417 4.875,4.76 0.365,0.344 10 false I104 3.01,3.281 3.406,3.573 0.396,0.292 10 false I93 3.958,3.281 4.292,3.573 0.333,0.292 10 false I93 0.219,0.125 0.99,0.438 0.771,0.313 12 false for RHD:

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EFI Communication Open EFI communication open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Yaw Rate Open Yaw rate sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Steering Open Steering angle sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
EFI Communication Open
Yaw Rate Open
Steering Open
50003 105 204,205,207
Result:
Result Proceed to
There is a constant interruption. (Error is displayed without interruption) A
There are no momentary interruptions. B
There are momentary interruptions. (Error is displayed intermittently) C


HINT:

Perform the above inspection before disconnecting any sensors or connectors.




A

2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED

B

3.RECONFIRM DTC

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED
a.

Turn the ignition switch off.


b.

Check if each sensor or ECM connector is securely connected.

OK:

Each connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Record the output DTCs.

for VSC system: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

for CAN communication system: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If CAN communication system DTCs and related sensor DTCs are output simultaneously, troubleshoot the DTCs (for VSC system) after the CAN communication system returns to normal.



Result:
Result Proceed to
DTC is not output. A
DTC is output. B
CAN communication system DTC is output. C



A

B

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Turn the ignition switch off.


b.

Repair or replace the harness or connector.


c.

Check for any momentary interruptions between the skid control ECU and each sensor or ECM.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.


f.

Check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


g.

If VSC system DTCs are output, record them.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output. A
DTC is output. B
CAN communication system DTC is output. C


HINT:

The CAN communication system must be normal when performing troubleshooting for sensor DTCs (for VSC system).




A

END

B

C