Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076219 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1429  Open or Short in Brake Pedal Load Sensing Switch  


DESCRIPTION

The brake pedal load sensing switch turns on when the brake pedal is depressed with a force exceeding a predetermined level.

The skid control ECU uses this circuit to detect if the brake pedal is depressed or not.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1429 Open or Short in Brake Pedal Load Sensing Switch An open or short in the brake pedal load sensing switch circuit continues for 0.5 seconds or more.
·

Brake pedal load sensing switch (Brake pedal support assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C168343E12
2.219,1.24 2.563,1.625 0.344,0.385 10 1 4.115,1.24 4.271,1.438 0.156,0.198 10 2 5.542,1.24 5.771,1.438 0.229,0.198 10 34 5.813,1.375 6.396,1.667 0.583,0.292 10 FSW+ 2.115,2.26 4.188,2.823 2.073,0.563 10 Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly) 5.385,3.083 6.938,3.542 1.552,0.458 10 Skid Control ECU (Brake Actuator Assembly) 3.615,1.156 4.219,1.521 0.604,0.365 10 FSW+ 2.406,1.156 2.958,1.51 0.552,0.354 10 FSW- 5.375,2.927 5.76,3.198 0.385,0.271 10 A49 2.104,2.094 2.5,2.323 0.396,0.229 10 A40

CAUTION / NOTICE / HINT

HINT:

When C1249, C1425 and/or C1426 is output together with C1429, inspect and repair the trouble areas indicated by C1249, C1425 and/or C1426 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1249

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1426


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (BRAKE PEDAL LOAD SENSING SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Pedal Load Sensing SW Brake pedal load sensing switch ON or OFF ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Brake Pedal Load Sensing SW
50003 105 39

d.

Check that the brake pedal load sensing switch display observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
2.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1429 is not output. A
DTC C1429 is output. B



A

B

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
a.
C239141C04
1.563,2.063 0.979,2.865 false 1.823,2.052 2.406,2.854 false 0.271,0.229 0.479,0.417 0.208,0.188 10 *a 0.688,2.896 1.146,3.083 0.458,0.188 10 FSW+ 2.25,2.896 2.708,3.083 0.458,0.188 10 FSW-
*a Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A40 brake pedal load sensing switch connector.

NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake pedal support assembly.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.




d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (FSW+) - 1 (FSW-) Switch OFF
(Brake pedal depressed)
950 to 1050 Ω
2 (FSW+) - 1 (FSW-) Switch ON
(Brake pedal released)
203 to 223 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)

B

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

C

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A49 skid control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-34 (FSW+) - A40-2 (FSW+) Always Below 1 Ω
A49-34 (FSW+) - Body ground Always 10 kΩ or higher
A40-1 (FSW-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR