Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076219 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1271  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1330  Open in Front Speed Sensor RH  C1331  Open in Front Speed Sensor LH  C1464  Front Speed Sensor RH  C1465  Front Speed Sensor LH  


DESCRIPTION

Each speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU.

These signals are used by the ABS control system.

The speed sensor rotors have 48 serrations. Hall IC type speed sensors use the frequency of output pulses to detect the vehicle speed. Because the sensor outputs digital pulses, it can detect the vehicle speed even when the vehicle is nearly stationary.

DTCs C1271 and C1272 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1271 and C1272 are output only in Test Mode.

C172023E18
1.5,0.833 1.5,0.302 1.5,0.302 1.365,0.302 false 5.208,1.823 5.99,2.031 0.781,0.208 10 High speed 4.271,1.823 4.979,1.979 0.708,0.156 10 Low speed 6.292,1.375 6.76,1.542 0.469,0.167 10 0.15 V 6.292,1.01 6.688,1.177 0.396,0.167 10 0.3 V 0.417,0.219 1.344,0.417 0.927,0.198 10 Speed Sensor 1.042,2.104 2.333,2.302 1.292,0.198 10 Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area
C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Sensor installation

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)


C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Sensor installation

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)


C1330 Open in Front Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


C1331 Open in Front Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


C1464 Front Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)


·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C1465 Front Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)


·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTCs C1271, C1330 and C1464 are for the front speed sensor RH.

·

DTCs C1272, C1331 and C1465 are for the front speed sensor LH.



WIRING DIAGRAM

C243493E02
1.177,1.094 1.302,1.25 0.125,0.156 10 1 2.344,1.094 2.469,1.25 0.125,0.156 10 2 1.042,1.479 1.354,1.625 0.313,0.146 10 A53 1.063,3.667 2.625,3.813 1.563,0.146 10 Front Speed Sensor LH 5.479,4.021 7.042,4.385 1.563,0.365 10 Skid Control ECU (Brake Actuator Assembly) 5.708,0.531 5.906,0.698 0.198,0.167 10 16 5.771,1.094 5.948,1.26 0.177,0.167 10 4 5.708,2.573 5.906,2.74 0.198,0.167 10 19 5.771,3.135 5.969,3.302 0.198,0.167 10 8 5.479,3.865 5.75,4.01 0.271,0.146 10 A49 5.99,0.698 6.313,0.854 0.323,0.156 10 FR+ 5.99,1.26 6.313,1.417 0.323,0.156 10 FR- 5.99,2.729 6.313,2.885 0.323,0.156 10 FL+ 5.99,3.292 6.313,3.448 0.323,0.156 10 FL- 1.042,1.635 2.615,1.781 1.573,0.146 10 Front Speed Sensor RH 1.063,3.521 1.375,3.667 0.313,0.146 10 A16 1.177,3.146 1.302,3.302 0.125,0.156 10 1 2.344,3.146 2.469,3.302 0.125,0.156 10 2 1.354,3.271 1.677,3.427 0.323,0.156 10 FL+ 2,3.281 2.323,3.438 0.323,0.156 10 FL- 1.354,1.25 1.677,1.406 0.323,0.156 10 FR+ 2,1.25 2.323,1.406 0.323,0.156 10 FR-

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Select the Data List using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2

d.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the intelligent tester is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check using the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3
OK:

All Test Mode DTCs are not output.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1330, C1331, C1464 and C1465 are not output. A
DTCs C1330, C1331, C1464 and/or C1465 are output. B



A

B

8.REPLACE FRONT SPEED SENSOR
4.CHECK FRONT SPEED SENSOR INSTALLATION
a.
C144929C05
0.833,1.625 0.833,0.76 false 0.833,0.76 0.979,0.76 false 0.698,2.479 0.958,2.792 false 0.958,2.792 1.073,2.792 false 0.625,2.885 0.906,3.083 0.281,0.198 10 OK 2.656,2.885 2.979,3.083 0.323,0.198 10 NG 1.115,2.708 2.031,2.906 0.917,0.198 10 No clearance 1.031,0.667 1.573,0.865 0.542,0.198 10 8.5 N*m 0.115,0.063 0.281,0.25 0.167,0.188 10 *1
*1 Front Speed Sensor


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.


Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR

NG

5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR
a.

Remove the front speed sensor and the component with the sensor rotor.

for speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for sensor rotor: Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY>REMOVAL


b.

Check the speed sensor tip and speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the sensor tip and rotor.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Install the front speed sensor and the component with the sensor rotor.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A49 skid control ECU connector and the A53 or A16 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A49-16 (FR+) - A53-1 (FR+) Always Below 1 Ω
A49-16 (FR+) - Body ground Always 10 kΩ or higher
A49-4 (FR-) - A53-2 (FR-) Always Below 1 Ω
A49-4 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A49-19 (FL+) - A16-1 (FL+) Always Below 1 Ω
A49-19 (FL+) - Body ground Always 10 kΩ or higher
A49-8 (FL-) - A16-2 (FL-) Always Below 1 Ω
A49-8 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.RECONFIRM DTC
a.

Reconnect the A49 skid control ECU connector and the A53 or A16 front speed sensor connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1330, C1331, C1464 and/or C1465 are output. A
DTCs C1330, C1331, C1464 and C1465 are not output. B



A

8.REPLACE FRONT SPEED SENSOR

B

8.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.


b.

Result:
Proceed to
NEXT



NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1330, C1331, C1464 and/or C1465 are output. A
DTCs C1330, C1331, C1464 and C1465 are not output. B



A

10.REPLACE FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY

B

END

10.REPLACE FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the front speed sensor rotor (front drive outboard joint shaft assembly).

Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY>REMOVAL

HINT:

If the front speed sensor rotor needs to be replaced, replace the front drive outboard joint shaft assembly.


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
NEXT



NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1330, C1331, C1464 and C1465 are not output. A
DTCs C1330, C1331, C1464 and/or C1465 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

END

B