Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076219 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1273  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1332  Open in Rear Speed Sensor RH  C1333  Open in Rear Speed Sensor LH  C1466  Rear Speed Sensor RH  C1467  Rear Speed Sensor LH  


DESCRIPTION

Each speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. These signals are used by the ABS control system.

The speed sensor rotors have rows of alternating N and S magnetic poles. Hall IC type speed sensors use the frequency of output pulses to detect the vehicle speed. Because the sensor outputs digital pulses, it can detect the vehicle speed even when the vehicle is nearly stationary.

DTCs C1273 and C1274 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1273 and C1274 are output only in Test Mode.

C151818E13
1.594,0.854 1.594,0.469 1.594,0.469 1.688,0.469 false 5.583,1.344 6,1.344 false 1.74,0.385 2.667,0.552 0.927,0.167 10 Speed Sensor 4.021,2.115 4.729,2.281 0.708,0.167 10 Low speed 6.083,1.26 6.448,1.427 0.365,0.167 10 0.3 V 6.083,1.625 6.563,1.792 0.479,0.167 10 0.15 V 4.99,2.115 5.719,2.313 0.729,0.198 10 High speed 0.969,2.177 2.26,2.344 1.292,0.167 10 Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area
C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Sensor installation

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)


C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Sensor installation

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)


C1332 Open in Rear Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


C1333 Open in Rear Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


C1466 Rear Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C1467 Rear Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTCs C1273, C1332 and C1466 are for the rear speed sensor RH.

·

DTCs C1274, C1333 and C1467 are for the rear speed sensor LH.



WIRING DIAGRAM

C243494E08
2.354,0.906 2.573,1.167 0.219,0.26 10 false 1 0.958,0.906 1.198,1.146 0.24,0.24 10 false 2 2.354,2.865 2.542,3.083 0.188,0.219 10 false 1 0.958,2.865 1.271,3.115 0.313,0.25 10 false 2 0.927,1.125 1.323,1.333 0.396,0.208 10 false h1 0.938,3.385 2.573,3.583 1.635,0.198 10 false Rear Speed Sensor LH 5.458,4 7.01,4.469 1.552,0.469 10 false Skid Control ECU (Brake Actuator Assembly) 5.729,0.458 6.021,0.729 0.292,0.271 10 false 17 5.729,1.01 6.021,1.271 0.292,0.26 10 false 29 5.729,2.417 5.969,2.656 0.24,0.24 10 false 31 5.729,2.969 6.052,3.25 0.323,0.281 10 false 18 5.458,3.844 5.729,3.99 0.271,0.146 10 false A49 5.979,0.563 6.396,0.854 0.417,0.292 10 false RR+ 5.979,1.115 6.406,1.385 0.427,0.271 10 false RR- 5.979,2.51 6.365,2.76 0.385,0.25 10 false RL+ 5.979,3.073 6.396,3.354 0.417,0.281 10 false RL- 0.927,1.417 2.615,1.635 1.688,0.219 10 false Rear Speed Sensor RH 0.948,3.083 1.365,3.323 0.417,0.24 10 false i1 2.333,1.125 2.698,1.333 0.365,0.208 10 false h1 0.708,1.792 2.719,2.042 2.01,0.25 10 false Skid Control Sensor Wire RH 2.979,0.313 3.104,0.469 0.125,0.156 10 false 1 2.979,0.906 3.198,1.156 0.219,0.25 10 false 2 2.896,0.552 3.302,0.802 0.406,0.25 10 false hO1 2.906,1.135 3.354,1.479 0.448,0.344 10 false hO1 2.344,3.083 2.74,3.302 0.396,0.219 10 false i1 0.708,3.729 2.667,4 1.958,0.271 10 false Skid Control Sensor Wire LH 3,2.302 3.208,2.542 0.208,0.24 10 false 1 3,2.875 3.25,3.156 0.25,0.281 10 false 2 2.927,2.521 3.302,2.74 0.375,0.219 10 false iN1 2.927,3.094 3.281,3.344 0.354,0.25 10 false iN1 1.26,3.083 1.677,3.323 0.417,0.24 10 false RL+ 1.896,3.083 2.281,3.375 0.385,0.292 10 false RL- 1.24,1.115 1.75,1.385 0.51,0.271 10 false RR+ 1.896,1.115 2.365,1.375 0.469,0.26 10 false RR-

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Select the Data List using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

d.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the intelligent tester is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check using the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3
OK:

All Test Mode DTCs are not output.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1332, C1333, C1466 and C1467 are not output. A
DTCs C1332, C1333, C1466 and/or C1467 are output. B



A

B

8.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
4.CHECK REAR SPEED SENSOR INSTALLATION
a.
C144931C08
0.99,1.49 1.188,0.813 1.188,0.813 1.333,0.813 false 0.156,0.115 0.333,0.302 0.177,0.188 10 false *1 1.375,0.729 2.26,0.917 0.885,0.188 10 false No clearance 0.885,2.792 1.146,2.979 0.26,0.188 10 false OK 2.302,2.792 2.563,2.979 0.26,0.188 10 false NG
*1 Rear Speed Sensor


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and rear axle carrier.



Result:
Proceed to
OK
NG



OK

5.INSPECT SKID CONTROL SENSOR WIRE

NG

5.INSPECT SKID CONTROL SENSOR WIRE
a.
C275487C01
0.188,0.677 0.51,0.906 0.323,0.229 1.823,0.698 2.146,0.927 0.323,0.229 0.198,2.844 0.521,3.073 0.323,0.229 1.833,2.865 2.156,3.094 0.323,0.229 0.563,2.073 0.969,1.333 false 2.219,2.073 2.427,1.573 false 1.552,2.073 1.229,1.323 false 2.938,2.073 2.667,1.594 false 1.563,4.396 1.24,3.646 false 0.552,4.385 0.958,3.646 false 2.125,4.406 2.333,3.906 false 2.948,4.396 2.677,3.917 false 0.25,0.125 0.563,0.323 0.313,0.198 10 *a 0.25,0.354 0.563,0.552 0.313,0.198 10 *A 0.281,0.708 0.594,0.906 0.313,0.198 10 h1 1.875,0.729 2.188,0.927 0.313,0.198 10 hO1 1.021,0.51 1.333,0.708 0.313,0.198 10 *b 2.396,0.552 2.708,0.75 0.313,0.198 10 *c 0.302,2.563 0.615,2.76 0.313,0.198 10 *B 0.313,2.875 0.625,3.073 0.313,0.198 10 i1 1.906,2.896 2.219,3.094 0.313,0.198 10 iN1 2.417,3.073 2.729,3.271 0.313,0.198 10 *c 1.01,2.896 1.323,3.094 0.313,0.198 10 *b 0.448,2.094 0.906,2.292 0.458,0.198 10 RR- 1.406,2.094 1.865,2.292 0.458,0.198 10 RR+ 2.115,2.094 2.573,2.292 0.458,0.198 10 RR+ 2.771,2.094 3.229,2.292 0.458,0.198 10 RR- 0.417,4.417 0.875,4.615 0.458,0.198 10 RL- 1.469,4.427 1.927,4.625 0.458,0.198 10 RL+ 1.938,4.438 2.396,4.635 0.458,0.198 10 RL+ 2.885,4.427 3.344,4.625 0.458,0.198 10 RL-
*A for RH
*B for LH
*a Front view of skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Remove the skid control sensor wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
h1-2 (RR+) - hO1-1 (RR+) Always Below 1 Ω
h1-2 (RR+) - hO1-2 (RR-) Always 10 kΩ or higher
h1-2 (RR+) - Body ground Always 10 kΩ or higher
h1-1 (RR-) - hO1-2 (RR-) Always Below 1 Ω
h1-1 (RR-) - hO1-1 (RR+) Always 10 kΩ or higher
h1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
i1-2 (RL+) - iN1-1 (RL+) Always Below 1 Ω
i1-2 (RL+) - iN1-2 (RL-) Always 10 kΩ or higher
i1-2 (RL+) - Body ground Always 10 kΩ or higher
i1-1 (RL-) - iN1-2 (RL-) Always Below 1 Ω
i1-1 (RL-) - iN1-1 (RL+) Always 10 kΩ or higher
i1-1 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)

NG

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A49 skid control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A49-17 (RR+) - hO1-1 (RR+) Always Below 1 Ω
A49-17 (RR+) - Body ground Always 10 kΩ or higher
A49-29 (RR-) - hO1-2 (RR-) Always Below 1 Ω
A49-29 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A49-31 (RL+) - iN1-1 (RL+) Always Below 1 Ω
A49-31 (RL+) - Body ground Always 10 kΩ or higher
A49-18 (RL-) - iN1-2 (RL-) Always Below 1 Ω
A49-18 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.RECONFIRM DTC
a.

Install the skid control sensor wire.


b.

Reconnect the A49 skid control ECU connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the ignition switch off.


e.

Start the engine.


f.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1332, C1333, C1466 and/or C1467 are output. A
DTCs C1332, C1333, C1466 and C1467 are not output. B



A

8.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

B

8.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL

HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
NEXT



NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1332, C1333, C1466 and C1467 are not output. A
DTCs C1332, C1333, C1466 and/or C1467 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

END

B