Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/o VSC) › 2011.10–2016.05
RM19V0EQ _58 Vehicle Interior _014610 SUPPLEMENTAL RESTRAINT SYSTEMS _0074159 AIRBAG SYSTEM(w/o VSC) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o VSC)  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1805/52 Short in Front Passenger Side Squib Circuit
·

The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit during primary check.

·

Front passenger side squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag sensor assembly


Applies to check mode
B1806/52 Open in Front Passenger Side Squib Circuit
·

The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag sensor assembly


Applies to check mode
B1807/52 Short to GND in Front Passenger Side Squib Circuit
·

The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag sensor assembly


Applies to check mode
B1808/52 Short to B+ in Front Passenger Side Squib Circuit
·

The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag sensor assembly


Applies to check mode

WIRING DIAGRAM

C239227E41
0.698,2.5 1.135,2.823 0.438,0.323 10 b1 0.698,2.656 3.563,3.219 2.865,0.563 10 Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib) 4.635,3.01 5.125,3.354 0.49,0.344 10 I47 4.698,1.99 5.031,2.375 0.333,0.385 10 P- 4.521,1.917 5.01,2.302 0.49,0.385 10 3 4.688,1.177 5.083,1.604 0.396,0.427 10 P+ 2.156,1.885 2.667,2.177 0.51,0.292 10 P- 2.125,1.073 2.521,1.354 0.396,0.281 10 P+ 4.521,1.073 5.052,1.49 0.531,0.417 10 4 2.406,1.906 2.729,2.281 0.323,0.375 10 1 2.406,1.073 2.729,1.479 0.323,0.406 10 2 3.469,1.792 3.802,2.135 0.333,0.344 10 2 3.469,0.948 3.833,1.344 0.365,0.396 10 1 3.427,1.167 3.958,1.677 0.531,0.51 10 Ib1 3.427,2 3.865,2.469 0.438,0.469 10 Ib1 4.635,3.198 6.333,3.729 1.698,0.531 10 Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C241746C01
0.271,0.99 0.271,1.427 false 1.76,1 1.76,1.438 false 0.979,0.875 0.979,0.5 0.979,0.5 0.823,0.5 false 0.198,1.448 0.573,1.781 0.375,0.333 10 *1 0.667,0.427 1.146,0.708 0.479,0.281 10 *3 2.708,1.188 3,1.5 0.292,0.313 10 *2 2.25,0.854 2.5,1.25 0.25,0.396 10 A 1.948,0.854 2.219,1.156 0.271,0.302 10 B 1.479,0.854 1.76,1.115 0.281,0.26 10 C 1.167,0.854 1.49,1.135 0.323,0.281 10 D 0.688,0.854 0.896,1.177 0.208,0.323 10 E 0.396,0.854 0.635,1.146 0.24,0.292 10 F 1.698,1.448 1.958,1.74 0.26,0.292 10 *4
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag sensor assembly. Also check that the connectors that link the instrument panel wire and No. 2 instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the instrument panel passenger airbag assembly and airbag sensor assembly. Also disconnect the instrument panel wire from the No. 2 instrument panel wire.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the No. 2 instrument panel wire connector (on the instrument panel passenger airbag assembly side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



g.

Check that the short springs for the instrument panel wire and No. 2 instrument panel wire with the activation prevention mechanism are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

NG

REPLACE WIRE HARNESS

2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
a.
C241747C03
0.385,2.385 0.708,2.604 0.323,0.219 0.385,0.667 0.385,0.927 false 1.75,2.281 2.031,2.281 false 0.323,0.948 0.771,1.26 0.448,0.313 10 *1 0.333,1.698 0.719,2.063 0.385,0.365 10 *a 2.063,2.208 2.417,2.531 0.354,0.323 10 SST 2.594,0.833 2.969,1.135 0.375,0.302 10 *2 2.177,0.531 2.375,0.74 0.198,0.208 10 A 2.021,0.531 2.198,0.844 0.177,0.313 10 B 1.531,0.531 1.813,0.771 0.281,0.24 10 C 1.375,0.521 1.677,0.885 0.302,0.365 10 D 0.896,0.521 1.177,0.927 0.281,0.406 10 E 0.5,0.521 0.844,0.813 0.344,0.292 10 F 0.479,2.417 0.854,2.719 0.375,0.302 10 b1
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)


Connect the instrument panel wire to the No. 2 instrument panel wire and airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect the tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.
C238254C10
0.688,2.292 1.021,2.531 0.333,0.24 0.375,0.656 0.375,0.938 false 1.479,2.104 1.167,2.104 false 1.958,2.094 1.646,2.094 false 0.5,0.5 0.979,0.99 0.479,0.49 10 F 0.802,0.5 1.208,1.01 0.406,0.51 10 E 1.26,0.5 1.552,0.938 0.292,0.438 10 D 1.406,0.5 1.688,0.885 0.281,0.385 10 C 1.865,0.5 2.104,0.99 0.24,0.49 10 B 2.177,0.5 2.448,0.969 0.271,0.469 10 A 0.313,0.958 0.667,1.292 0.354,0.333 10 *1 2.583,0.813 2.896,1.052 0.313,0.24 10 *2 0.271,1.74 0.583,2.115 0.313,0.375 10 *a 0.979,2.031 1.417,2.313 0.438,0.281 10 P- 2.01,2.021 2.302,2.281 0.292,0.26 10 P+ 0.781,2.333 1.198,2.771 0.417,0.438 10 b1
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)


Disconnect the instrument panel wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
b1-2 (P+) - Body ground Ignition switch ON Below 1 V
b1-1 (P-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 (P+) - b1-1 (P-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 (P+) - Body ground Always 1 MΩ or higher
b1-1 (P-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 (P+) - b1-1 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C238235C01
0.5,0.875 0.5,1.219 false 2.438,1.031 2.75,1.313 0.313,0.281 10 *2 0.427,1.24 0.854,1.573 0.427,0.333 10 *1 0.635,0.74 1.188,1.167 0.552,0.427 10 F 0.792,0.74 1.188,1.083 0.396,0.344 10 E 1.24,0.74 1.594,1.083 0.354,0.344 10 D 1.396,0.74 1.698,1.167 0.302,0.427 10 C 1.844,0.74 2.135,1.042 0.292,0.302 10 B 2,0.74 2.271,0.969 0.271,0.229 10 A
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly


Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.
C238255C12
0.729,2.375 1.01,2.563 0.281,0.188 0.292,0.656 0.292,0.938 false 1.01,0.656 1.01,0.938 false 1.646,2.615 1.323,2.896 false 1.813,2.604 2.146,2.885 false 1.76,0.51 1.76,0.115 1.76,0.115 1.531,0.115 false 0.438,0.51 0.698,0.729 0.26,0.219 10 F 0.729,0.51 0.979,0.729 0.25,0.219 10 E 1.188,0.51 1.448,0.74 0.26,0.229 10 D 1.5,0.51 1.781,0.75 0.281,0.24 10 C 1.948,0.51 2.208,0.844 0.26,0.333 10 B 2.25,0.51 2.531,0.833 0.281,0.323 10 A 0.229,0.948 0.552,1.188 0.323,0.24 10 *1 2.656,0.813 2.917,1.063 0.26,0.25 10 *2 0.385,1.75 0.896,2.063 0.51,0.313 10 *a 2.125,2.896 2.5,3.094 0.375,0.198 10 P- 0.948,0.948 1.26,1.167 0.313,0.219 10 *3 1.229,2.906 1.573,3.125 0.344,0.219 10 P+ 0.792,2.396 1.208,2.667 0.417,0.271 10 Ib1 1.385,0.042 1.76,0.313 0.375,0.271 10 *4
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


Disconnect the No. 2 instrument panel wire from the instrument panel wire.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Ib1-1 (P+) - Body ground Ignition switch ON Below 1 V
Ib1-2 (P-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ib1-1 (P+) - Ib1-2 (P-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ib1-1 (P+) - Body ground Always 1 MΩ or higher
Ib1-2 (P-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ib1-1 (P+) - Ib1-2 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK NO. 2 INSTRUMENT PANEL WIRE
a.
C238256C05
0.531,2.323 0.865,2.552 0.333,0.229 0.281,0.656 0.281,0.938 false 1.781,0.656 1.781,0.938 false 1.479,2.104 1.125,2.104 false 2.01,2.104 1.646,2.104 false 1,0.51 1,0.208 1,0.208 1.156,0.208 false 0.427,0.51 0.688,0.844 0.26,0.333 10 F 0.729,0.51 1.094,0.875 0.365,0.365 10 E 1.177,0.51 1.521,0.896 0.344,0.385 10 D 1.5,0.51 1.688,0.823 0.188,0.313 10 C 1.948,0.51 2.219,0.854 0.271,0.344 10 B 2.26,0.51 2.604,0.823 0.344,0.313 10 A 0.208,0.948 0.5,1.323 0.292,0.375 10 *1 2.656,0.802 3.021,1.177 0.365,0.375 10 *2 0.281,1.76 0.625,2.167 0.344,0.406 10 *a 0.948,2.031 1.281,2.302 0.333,0.271 10 P- 1.708,0.969 2.031,1.292 0.323,0.323 10 *4 2.052,2.031 2.323,2.292 0.271,0.26 10 P+ 0.625,2.365 0.948,2.76 0.323,0.396 10 b1 1.188,0.135 1.479,0.448 0.292,0.313 10 *3
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
b1-2 (P+) - Body ground Ignition switch ON Below 1 V
b1-1 (P-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 (P+) - b1-1 (P-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 (P+) - Body ground Always 1 MΩ or higher
b1-1 (P-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 (P+) - b1-1 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE