Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074130 ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System) Y

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use this procedure to troubleshoot the theft deterrent system.

·

*: Use the intelligent tester.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


HINT:

A simple method to determine whether the battery is discharged is to operate the horn.



Result:
Proceed to
NEXT



NEXT

3.TURN ENGINE SWITCH ON (IG)
3.TURN ENGINE SWITCH ON (IG)
HINT:

If the engine switch cannot be turned on (IG), communication with the intelligent tester can be confirmed by connecting the intelligent tester to the vehicle and turning a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN DTC is not output. A
CAN DTC is output. B



A

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

B

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Use the intelligent tester to check if the LIN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
LIN DTC is not output. A
LIN DTC is output. B



A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*
a.

Check for DTCs and make a note of any codes that are output.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Body Electrical > Entry&Start > Trouble Codes
50001 125

b.

Based on the DTCs output above, proceed to each diagnostic procedure.


Result:
Result Proceed to
DTC is not output. A
SFI system DTC is output. B
Steering lock system DTC is output. C
Engine immobiliser system DTC is output. D



A

7.PROBLEM SYMPTOMS TABLE

B

C

D

7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in problem symptoms table. A
Fault is listed in problem symptoms table. B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

9.REPAIR OR REPLACE
9.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC*
10.CHECK FOR DTC*
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Body Electrical > Entry&Start > Clear DTCs
50002 125

b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DIAGNOSTIC TROUBLE CODE CHART



Result:
Result Proceed to
DTC is not output. A
Engine immobiliser system DTC is output. B



A

END

B