Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM19V0EQ _58 Vehicle Interior _014611 SEAT _0074168 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat Position is not Memorized  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives seat memory switch signals from the outer mirror control ECU assembly RH via CAN communication. If the seat memory SET switch is being pressed when one of the M1 or M2 switches is pressed, or if one of the M1 or M2 switches is pressed within 3 seconds of pressing the seat memory SET switch, the main body ECU (multiplex network body ECU) sends a memory request signal to the position control ECU and switch assembly. After receiving the request signal, the position control ECU and switch assembly memorizes the location data of each motor.

WIRING DIAGRAM

B293826
1.063,2.25 1.521,2.458 0.458,0.208 10 false CAN 1.063,0.625 1.448,0.854 0.385,0.229 10 false CAN 3.469,0.604 3.792,0.75 0.323,0.146 10 false CAN 3.49,2.365 3.813,2.51 0.323,0.146 10 false GND 3.375,2.802 3.948,3.146 0.573,0.344 10 false J13 4.406,0.458 4.729,0.74 0.323,0.281 10 false M1 4.698,0.344 4.927,0.49 0.229,0.146 10 false 2 4.698,1 4.927,1.146 0.229,0.146 10 false 3 4.698,1.656 4.927,1.802 0.229,0.146 10 false 1 4.698,2.25 5,2.531 0.302,0.281 10 false 13 3.302,2.229 3.479,2.375 0.177,0.146 10 false 7 5.365,0.344 5.531,0.49 0.167,0.146 10 false 4 5.365,1 5.531,1.146 0.167,0.146 10 false 3 5.365,1.656 5.531,1.802 0.167,0.146 10 false 2 5.365,2.25 5.531,2.396 0.167,0.146 10 false 1 5.542,0.344 5.917,0.49 0.375,0.146 10 false M1 5.542,1.01 5.99,1.313 0.448,0.302 10 false M2 5.542,1.656 6.135,1.917 0.594,0.26 10 false MRY 5.552,2.25 5.76,2.427 0.208,0.177 10 false E 4.396,1.115 4.74,1.344 0.344,0.229 10 false M2 4.354,1.781 4.708,2.031 0.354,0.25 10 false MM 4.167,2.375 4.698,2.563 0.531,0.188 10 false MSWE 0.25,1.198 1.823,1.635 1.573,0.438 10 false Position Control ECU and Switch Assembly 0.135,2.792 1.771,3.26 1.635,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 3.365,2.979 4.969,3.354 1.604,0.375 10 false Outer Mirror Control ECU Assembly RH 5.563,2.813 5.906,3.083 0.344,0.271 10 false J16 5.563,2.969 6.969,3.219 1.406,0.25 10 false Seat Memory Switch 0.719,3.458 2.469,3.635 1.75,0.177 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

·

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL SYSTEM
a.

Check that each function of the power seat operates normally by using the power seat switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the power seat switch.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)

NG

2.READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Mirror R / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Mirror R > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 M1 switch ON or OFF ON: M1 switch on
OFF: M1 switch off
-
Seat Memory Switch2 M2 switch ON or OFF ON: M2 switch on
OFF: M2 switch off
-
Seat Memory Set SW SET switch ON or OFF ON: SET switch on
OFF: SET switch off
-
OK:

ON or OFF is displayed on the intelligent tester according to the table above.


Body Electrical > Mirror R > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Set SW
50003 224 1,2,4

Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BUZZER)

NG

8.INSPECT SEAT MEMORY SWITCH
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BUZZER)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer Buzzer operation OFF/ON -
Body Electrical > Driver Seat > Active Test
Tester Display
Buzzer
50004 162 5
OK:

Buzzer sounds normally.



Result:
Proceed to
OK
NG



OK

4.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

4.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH
a.

Replace the outer mirror control ECU assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK SEAT POSITION MEMORY FUNCTION
5.CHECK SEAT POSITION MEMORY FUNCTION
a.

Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat position memory function operates normally.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY RH WAS DEFECTIVE)

NG

6.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
6.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Replace the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK SEAT POSITION MEMORY FUNCTION
7.CHECK SEAT POSITION MEMORY FUNCTION
a.

Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat position memory function operates normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

8.INSPECT SEAT MEMORY SWITCH
a.
B293836
1.052,1.146 1.052,1.375 false 1.5,1.146 1.5,1.375 false 1.938,1.146 1.938,1.375 false 0.302,1.948 0.604,2.281 0.302,0.333 10 false *a 0.958,1.406 1.25,1.865 0.292,0.458 10 false *1 1.406,1.406 1.635,1.771 0.229,0.365 10 false *2 1.854,1.406 2.104,1.708 0.25,0.302 10 false *3
*1 M1 Switch
*2 M2 Switch
*3 SET Switch
*a Component without harness connected
(Seat Memory Switch)


Remove the seat memory switch.

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 SET switch is pressed Below 1 Ω
4 - 1 M1 switch is pressed Below 1 Ω
3 - 1 M2 switch is pressed Below 1 Ω
2 - 1 SET switch is not pressed 10 kΩ or higher
4 - 1 M1 switch is not pressed 10 kΩ or higher
3 - 1 M2 switch is not pressed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - SEAT MEMORY SWITCH)

NG

REPLACE SEAT MEMORY SWITCH

9.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - SEAT MEMORY SWITCH)
a.

Disconnect the J13 outer mirror control ECU assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J16-2 (MRY) - J13-1 (MM) Always Below 1 Ω
J16-4 (M1) - J13-2 (M1) Always Below 1 Ω
J16-3 (M2) - J13-3 (M2) Always Below 1 Ω
J16-1 (E) - J13-13 (MSWE) Always Below 1 Ω
J13-7 (GND) - Body ground Always Below 1 Ω
J13-1 (MM) - Body ground Always 10 kΩ or higher
J13-2 (M1) - Body ground Always 10 kΩ or higher
J13-3 (M2) - Body ground Always 10 kΩ or higher
J13-13 (MSWE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR