Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM19V0EQ _58 Vehicle Interior _014607 LIGHTING (INT) _0074132 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Engine Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the engine switch illumination.

WIRING DIAGRAM

E212454E16
2.968,1.179 3.39,1.354 0.422,0.175 10 AGND 4.735,1.266 5.157,1.441 0.422,0.175 10 AGND 3.033,0.784 3.391,0.958 0.357,0.175 10 SWIL 4.735,0.871 5.093,1.046 0.357,0.175 10 SWIL 4.484,1.179 4.659,1.354 0.175,0.175 10 24 4.487,0.784 4.659,0.958 0.172,0.175 10 16 3.466,1.179 3.564,1.354 0.098,0.175 10 6 3.466,0.784 3.562,0.958 0.096,0.175 10 9 1.833,1.69 2.143,1.865 0.31,0.175 10 I58 1.833,1.849 2.949,2.024 1.116,0.175 10 Engine Switch 4.32,1.62 4.655,1.795 0.334,0.175 10 I78 4.32,1.779 6.137,2.112 1.816,0.332 10 Certification ECU (Smart Key ECU Assembly)

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Active Test.


e.

Check that the illumination operates.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power/Engine SW Light Engine switch light OFF/ON When performing this Active Test, make sure the following condition is met:
The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the engine switch is on (ACC) or on (IG), or the engine is running.
Body Electrical > Entry&Start > Active Test
Tester Display
Power/Engine SW Light
50004 125 27
OK:

Engine switch illumination comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ENGINE SWITCH
2.INSPECT ENGINE SWITCH
a.

b.

Inspect the engine switch.

Click hereEngine / Hybrid System>2AR-FE STARTING>ENGINE SWITCH>INSPECTION

OK:

Engine switch illumination comes on.


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I78 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I58 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I58-9 (SWIL) - I78-16 (SWIL) Always Below 1 Ω
I58-6 (AGND) - I78-24 (AGND) Always Below 1 Ω
I58-9 (SWIL) - Body ground Always 10 kΩ or higher
I58-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR