Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM19V0EQ _58 Vehicle Interior _014607 LIGHTING (INT) _0074132 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Door Unlock Detection Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.

WIRING DIAGRAM

E212453E16
5.656,1.375 5.833,1.552 0.177,0.177 10 18 5.615,2.625 6.125,2.927 0.51,0.302 10 MB 4.438,2.406 4.615,2.583 0.177,0.177 10 17 4.438,3.448 4.615,3.625 0.177,0.177 10 53 4.427,3.656 4.99,3.854 0.563,0.198 10 3A 4.427,2.625 4.958,2.948 0.531,0.323 10 3C 6,1.563 6.458,1.74 0.458,0.177 10 LSFR 2.698,0.448 3.083,0.625 0.385,0.177 10 LSSR 6,2.594 6.458,2.771 0.458,0.177 10 LSR 5.708,0.344 5.802,0.521 0.094,0.177 10 7 5.688,2.406 5.781,2.583 0.094,0.177 10 5 5.646,0.563 5.917,0.74 0.271,0.177 10 I13 5.646,1.594 5.917,1.771 0.271,0.177 10 I13 6,0.531 6.458,0.708 0.458,0.177 10 LSFL 1.365,0.729 1.844,0.906 0.479,0.177 10 K1 1.365,0.885 3.99,1.063 2.625,0.177 10 Front Door Lock with Motor Assembly LH 1.354,1.75 1.833,1.927 0.479,0.177 10 J1 1.354,1.906 4.01,2.083 2.656,0.177 10 Front Door Lock with Motor Assembly RH 1.385,2.771 1.865,2.948 0.479,0.177 10 M1 1.385,2.927 3.979,3.104 2.594,0.177 10 Rear Door Lock with Motor Assembly LH 1.365,3.792 1.844,3.969 0.479,0.177 10 L1 1.365,3.948 3.99,4.125 2.625,0.177 10 Rear Door Lock with Motor Assembly RH 1.844,0.448 1.938,0.625 0.094,0.177 10 7 3.146,0.448 3.24,0.625 0.094,0.177 10 8 2.698,1.479 3.083,1.656 0.385,0.177 10 LSSR 1.844,1.479 1.938,1.656 0.094,0.177 10 8 2.031,1.479 2.167,1.656 0.135,0.177 10 E 2.031,0.448 2.167,0.625 0.135,0.177 10 E 3.146,1.479 3.24,1.656 0.094,0.177 10 7 2.698,2.51 3.083,2.688 0.385,0.177 10 LSSR 1.844,2.51 1.938,2.688 0.094,0.177 10 9 2.031,2.51 2.167,2.688 0.135,0.177 10 E 3.146,2.51 3.24,2.688 0.094,0.177 10 6 2.698,3.542 3.083,3.719 0.385,0.177 10 LSSR 1.844,3.542 1.938,3.719 0.094,0.177 10 9 2.031,3.542 2.167,3.719 0.135,0.177 10 E 3.146,3.542 3.24,3.719 0.094,0.177 10 6 4.354,3.938 5.906,4.271 1.552,0.333 10 Instrument Panel Junction Block Assembly 5.458,4.74 7.104,5.073 1.646,0.333 10 Main Body ECU (Multiplex Network Body ECU)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
RR-Door Lock Pos SW Rear door RH unlock detection switch signal ON or OFF ON: Rear door LH locked and rear door RH unlocked
ON: Rear door LH unlocked and rear door RH locked
ON: Rear door LH and rear door RH unlocked
OFF: Rear door LH and rear door RH locked
-
RL-Door Lock Pos SW Rear door LH unlock detection switch ON or OFF ON: Rear door LH locked and rear door RH unlocked
ON: Rear door LH unlocked and rear door RH locked
ON: Rear door LH and rear door RH unlocked
OFF: Rear door LH and rear door RH locked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Pos
FL Door Lock Pos
RR-Door Lock Pos SW
RL-Door Lock Pos SW
50003 123 196,198,51,52
Result:
Result Proceed to
OK A
Front door unlock detection switch LH does not operate B
Front door unlock detection switch RH does not operate C
Rear door unlock detection switch LH or rear door unlock detection switch RH does not operate D




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH

C

4.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH

D

6.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH
2.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH
a.

Remove the front door lock with motor assembly LH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.

Inspect the front door lock with motor assembly LH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION

OK:

Front door lock with motor assembly LH is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the K1 front door lock with motor assembly LH connector.


b.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K1-8 (LSSR) - I13-7 (LSFL) Always Below 1 Ω
K1-8 (LSSR) - Body ground Always 10 kΩ or higher
K1-7 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH
a.

Remove the front door lock with motor assembly RH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.

Inspect the front door lock with motor assembly RH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION

OK:

Front door lock with motor assembly RH is normal.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the J1 front door lock with motor assembly RH connector.


b.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-7 (LSSR) - I13-18 (LSFR) Always Below 1 Ω
J1-7 (LSSR) - Body ground Always 10 kΩ or higher
J1-8 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH
a.

Remove the rear door lock with motor assembly LH.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>REMOVAL


b.

Inspect the rear door lock with motor assembly LH.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION

OK:

Rear door lock with motor assembly LH is normal.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK WITH MOTOR ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR DOOR LOCK WITH MOTOR ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK WITH MOTOR ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the M1 rear door lock with motor assembly LH connector.


b.

Disconnect the 3C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M1-6 (LSSR) - 3C-17 Always Below 1 Ω
M1-6 (LSSR) - Body ground Always 10 kΩ or higher
M1-9 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH
a.

Remove the rear door lock with motor assembly RH.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>REMOVAL


b.

Inspect the rear door lock with motor assembly RH.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION

OK:

Rear door lock with motor assembly RH is normal.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK WITH MOTOR ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR DOOR LOCK WITH MOTOR ASSEMBLY RH

9.CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK WITH MOTOR ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the L1 rear door lock with motor assembly RH connector.


b.

Disconnect the 3A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L1-6 (LSSR) - 3A-53 Always Below 1 Ω
L1-6 (LSSR) - Body ground Always 10 kΩ or higher
L1-9 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E227412C02
1.978,0.244 2.293,0.454 0.315,0.21 2.057,0.277 2.315,0.484 0.258,0.207 10 3A 4.943,0.216 5.259,0.426 0.315,0.21 5.011,0.249 5.269,0.456 0.258,0.207 10 3C 2.487,1.57 2.802,1.781 0.315,0.21 2.538,1.603 2.796,1.81 0.258,0.207 10 MB 1.66,2.486 2.083,2.668 0.422,0.182 10 LSR 1.595,2.131 1.758,2.465 false 0.086,0.011 0.27,0.199 0.184,0.189 10 *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3C-17 - MB-5 (LSR) Always Below 1 Ω
3A-53 - MB-5 (LSR) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY