Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM19V0EQ _59 Vehicle Exterior _014619 MIRROR (EXT) _0074232 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Power Mirrors do not Return to Memorized Position  


SYSTEM DESCRIPTION

If either the M1 or M2 seat memory switch is pressed, the outer mirror control ECU assembly (driver door) detects the seat memory switch status and sends the switch signal to the main body ECU (multiplex network body ECU) via CAN communication. The main body ECU (multiplex network body ECU) sends back reproduction signals to each outer mirror control ECU assembly via CAN communication. When receiving the reproduction signals, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors, which are built into the outer mirror actuator assembly, to adjust the mirror surface to the stored position.

WIRING DIAGRAM

B294401E08
0.188,6.031 1.354,6.635 1.167,0.604 10 false Main Body ECU (Multiplex Network Body ECU) 0.875,5.219 1.5,5.49 0.625,0.271 10 false CANN 0.635,7.229 1.49,7.573 0.854,0.344 10 false : CAN 3.417,6.729 4,6.99 0.583,0.26 10 false CANN 3.094,4.833 4.667,5.281 1.573,0.448 10 false Outer Mirror Control ECU Assembly (Driver Door) 5.625,7.167 6.948,7.688 1.323,0.521 10 false Outer Mirror Actuator Assembly LH 5.604,2.188 6.896,2.594 1.292,0.406 10 false Outer Mirror Actuator Assembly RH 2.865,7.229 5.073,7.719 2.208,0.49 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 3.417,3.094 4.021,3.458 0.604,0.365 10 false CANN 0.865,2.594 1.542,2.833 0.677,0.24 10 false CANP 3.438,5.979 4.042,6.24 0.604,0.26 10 false CANP 3.417,1.521 4.021,1.833 0.604,0.313 10 false CANP 4.521,4.302 4.948,4.583 0.427,0.281 10 false J13 4.521,3.021 4.99,3.323 0.469,0.302 10 false J13 4.521,3.448 5.01,3.74 0.49,0.292 10 false J13 4.521,3.865 4.948,4.135 0.427,0.271 10 false J13 3.063,5.958 3.469,6.229 0.406,0.271 10 false K12 3.063,6.708 3.479,6.979 0.417,0.271 10 false K12 4.083,5.792 4.531,6.052 0.448,0.26 10 false LVC 4.104,6.896 4.5,7.167 0.396,0.271 10 false LE1 3.979,6.167 4.469,6.427 0.49,0.26 10 false VSSR 3.979,6.531 4.531,6.802 0.552,0.271 10 false HSSR 4.073,0.323 4.563,0.542 0.49,0.219 10 false RVC 4.104,1.906 4.51,2.198 0.406,0.292 10 false RE1 3.979,0.854 4.542,1.083 0.563,0.229 10 false VSSR 3.979,1.375 4.49,1.604 0.51,0.229 10 false HSSR 4.177,3.021 4.542,3.302 0.365,0.281 10 false M1 4.125,3.865 4.51,4.104 0.385,0.24 10 false MM 3.938,4.292 4.51,4.5 0.573,0.208 10 false MSWE 4.177,3.458 4.583,3.792 0.406,0.333 10 false M2 5.74,3.021 6.188,3.323 0.448,0.302 10 false M1 5.74,3.854 6.125,4.135 0.385,0.281 10 false MRY 5.74,4.302 5.938,4.552 0.198,0.25 10 false E 5.74,3.427 6.104,3.677 0.365,0.25 10 false M2 5.573,2.917 5.802,3.208 0.229,0.292 10 false 4 5.573,3.74 5.802,4.01 0.229,0.271 10 false 2 5.573,4.198 5.802,4.427 0.229,0.229 10 false 1 5.573,3.344 5.833,3.625 0.26,0.281 10 false 3 4.604,0.094 4.781,0.333 0.177,0.24 10 false 5 4.552,1.885 4.885,2.135 0.333,0.25 10 false z7 4.563,0.323 4.854,0.594 0.292,0.271 10 false z7 4.563,0.833 4.854,1.104 0.292,0.271 10 false z7 4.563,1.375 4.865,1.615 0.302,0.24 10 false z7 4.552,1.688 4.885,1.938 0.333,0.25 10 false 14 3.146,5.75 3.448,6.063 0.302,0.313 10 false 9 3.146,1.313 3.354,1.583 0.208,0.271 10 false 9 1.344,5.052 1.688,5.292 0.344,0.24 10 false 10 0.198,5.865 0.74,6.167 0.542,0.302 10 false I12 2.885,7.083 3.417,7.458 0.531,0.375 10 false z6 5.604,4.979 7.021,5.271 1.417,0.292 10 false Seat Memory Switch 5.604,4.823 6.031,5.083 0.427,0.26 10 false J16 3.146,6.5 3.365,6.75 0.219,0.25 10 false 8 1.323,2.427 1.563,2.677 0.24,0.25 10 false 9 3.146,2.875 3.365,3.146 0.219,0.271 10 false 8 4.552,4.083 4.844,4.26 0.292,0.177 10 false 13 4.604,0.635 4.813,0.875 0.208,0.24 10 false 6 4.563,1.156 4.833,1.385 0.271,0.229 10 false 13 4.594,2.802 4.802,3.052 0.208,0.25 10 false 2 4.594,3.656 4.698,3.792 0.104,0.135 10 false 1 4.594,3.24 4.813,3.448 0.219,0.208 10 false 3 4.448,5.677 4.75,6.01 0.302,0.333 10 false 5 4.448,6.781 4.719,7.063 0.271,0.281 10 false 14 4.448,6.042 4.833,6.396 0.385,0.354 10 false 6 4.448,6.417 4.823,6.719 0.375,0.302 10 false 13 3.073,3.073 3.458,3.333 0.385,0.26 10 false J13 3.063,1.51 3.458,1.771 0.396,0.26 10 false J13

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

OK:

CAN communication DTC is not output.



Result:
Proceed to
OK
NG



OK

2.CHECK SEAT MEMORY SWITCH FUNCTION

NG

GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

2.CHECK SEAT MEMORY SWITCH FUNCTION
a.

When any seat memory switch (M1 or M2 switch) is pressed, check that the driver seat moves to the memorized position.

OK:

The driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

3.CHECK POWER MIRROR CONTROL FUNCTION (ELECTRICAL REMOTE CONTROL MIRROR FUNCTION)

NG

GO TO POWER SEAT CONTROL SYSTEM (Power Seat does not Return to Memorized Position)

3.CHECK POWER MIRROR CONTROL FUNCTION (ELECTRICAL REMOTE CONTROL MIRROR FUNCTION)
a.

Check the electrical remote control mirror function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Electrical remote control mirror function is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION MEMORY)

NG

4.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION MEMORY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Mirror L or Mirror R / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Mirror L > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Memory No.1 Mirror position memorized in seat memory switch M1 ON or OFF ON: Memorized
OFF: Not memorized
-
Mirror Memory No.2 Mirror position memorized in seat memory switch M2 ON or OFF ON: Memorized
OFF: Not memorized
-
Mirror Memory No.3 Mirror position memorized in memory switch M3* ON or OFF ON: Memorized
OFF: Not memorized
Not applicable
Body Electrical > Mirror L > Data List
Tester Display
Mirror Memory No.1
Mirror Memory No.2
Mirror Memory No.3
50003 225 5,6,7
Body Electrical > Mirror R > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Memory No.1 Mirror position memorized in seat memory switch M1 ON or OFF ON: Memorized
OFF: Not memorized
-
Mirror Memory No.2 Mirror position memorized in seat memory switch M2 ON or OFF ON: Memorized
OFF: Not memorized
-
Mirror Memory No.3 Mirror position memorized in memory switch M3* ON or OFF ON: Memorized
OFF: Not memorized
Not applicable
Body Electrical > Mirror R > Data List
Tester Display
Mirror Memory No.1
Mirror Memory No.2
Mirror Memory No.3
50003 224 5,6,7
OK:

ON (Memorized) appears on the screen.



Result:
Proceed to
OK
NG



OK

5.CHECK MEMORY AND REACTIVATION FUNCTION

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Mirror Surface Position is not Memorized)

5.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C06
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Left Fully


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

Result:
Result Proceed to
Memory and reactivation functions on both mirrors are not normal A
Memory and reactivation functions on RH side mirror are not normal B
Memory and reactivation functions on LH side mirror are not normal C




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

6.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

C

8.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH
6.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Replace the outer mirror actuator assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK MEMORY AND REACTIVATION FUNCTION
7.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C07
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Left Fully


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

OK:

Memory and reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (OUTER REAR VIEW MIRROR ASSEMBLY RH WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

8.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Replace the outer mirror actuator assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK MEMORY AND REACTIVATION FUNCTION
9.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C08
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Left Fully


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

OK:

Memory and reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (OUTER REAR VIEW MIRROR ASSEMBLY LH WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)