When either the M1 or M2 switches is pressed, the outer mirror control ECU assembly RH sends a switch signal to the main body ECU (multiplex network body ECU) via CAN communication. Then, the main body ECU (multiplex network body ECU) sends a recall request signal to the position control ECU and switch assembly. The position control ECU and switch assembly operates each motor to achieve each memorized position value.
The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING).
Check that each function of the power seat operates normally by using the switches on the power seat switch.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Each function of the power seat operates normally using the switches on the power seat switch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
The seat position will not be recorded if the SET switch and 2 of the memory switches are pressed simultaneously.
If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.
Seat position memory function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Under each of the following conditions, check that the seat position restoring function operates by pressing the M1 switch or M2 switch.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Engine switch is off.
The engine switch is on (IG), and the shift lever is in P.*1
The engine switch is turned off within 180 seconds after the driver door is closed and opened.*2
The engine switch is turned off within 60 seconds after the driver door is opened and closed.*3
| Result | Proceed to |
|---|---|
| Seat position restoring function does not operate at all. | A |
| Seat position restoring function does not operate when the condition is *1. | B |
·
Seat position restoring function does not operate when the condition is *2. ·
Seat position restoring function does not operate when the condition is *3. |
C |
A
B
C
Store a seat position in memory for each of the M1 and M2 switches.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Driver Seat / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory No1 | Seat position memorized with M1 switch | Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Seat Memory No2 | Seat position memorized with M2 switch | Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Tester Display |
|---|
| Seat Memory No1 |
| Seat Memory No2 |
Mem appears on the intelligent tester screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the outer mirror control ECU assembly RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Restore a memorized seat position.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.
The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.
If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.
Seat position restoring function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the position control ECU and switch assembly.
Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Store a seat position in memory.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Restore a memorized seat position.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.
The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.
If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.
Seat position restoring function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Driver Seat / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P Switch | Park state signal | ON or OFF | ON: Shift lever in P
OFF: Shift lever in a position other than P |
- |
| Tester Display |
|---|
| P Switch |
On the intelligent tester screen, the item changes between ON and OFF according to the above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy | Front door courtesy light switch assembly signal | ON or OFF | ON: Driver door open
OFF: Driver door closed |
- |
| Tester Display |
|---|
| FR Door Courtesy SW |
On the intelligent tester screen, the item changes between ON and OFF according to the above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG