Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM19V0EQ _58 Vehicle Interior _034909 PRE-CRASH SAFETY _0163370 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  Pre-crash Safety System Circuit  


DESCRIPTION

This circuit provides power to operate the driving support ECU assembly.

WIRING DIAGRAM

E259149E35
1.073,0.51 2.646,1.031 1.573,0.521 10 false from IG1 NO. 3 Relay 5.979,0.51 6.385,0.75 0.406,0.24 10 false B 5.708,1.323 5.958,1.49 0.25,0.167 10 false 25 5.979,1.406 6.313,1.552 0.333,0.146 10 false GND 5.708,0.427 6.01,0.76 0.302,0.333 10 false 30 5.948,2.083 6.948,2.458 1,0.375 10 false Driving Support ECU Assembly 5.573,2.094 5.938,2.458 0.365,0.365 10 false I191 3.615,0.667 4.615,0.948 1,0.281 10 false ECU-IG1 NO. 3

PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
a.

Check the customer problem analysis and symptom.


Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the engine switch off.

Standard Voltage:

11 to 14 V



b.

Using the parts location and system diagram, check the system for blown-out fuses, open or short circuits in the wire harness(es) and connectors that are not properly connected by performing a visual check.

HINT:

If the voltage is 11 V or less, replace or recharge the auxiliary battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

3.CHECK DRIVING SUPPORT ECU ASSEMBLY
3.CHECK DRIVING SUPPORT ECU ASSEMBLY
a.
E298303C13
1.563,0.281 1.927,0.531 0.365,0.25 0.885,1.813 1.26,1.281 true 1.896,1.802 1.781,1.271 true 1.635,0.333 2.094,0.479 0.458,0.146 10 false I191 0.167,0.156 0.625,0.302 0.458,0.146 10 false *a 1.854,1.833 2.313,1.979 0.458,0.146 10 false B 0.688,1.844 1.146,1.99 0.458,0.146 10 false GND
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Check driving support ECU assembly.

NOTICE:

As the connector may be damaged if a load of more than 10 kg (22 lb) is applied to it, do not apply any more load than necessary to the connector.


i.

Disconnect the driving support ECU assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

NOTICE:

DTCs may be output when connectors are disconnected during inspection. Therefore, make sure to clear the DTCs using the GTS once the inspection has been completed.


Standard Voltage:
Tester Connection Condition Specified Condition
I191-30 (B) - Body ground Engine switch on (IG) 11 to 14 V
I191-30 (B) - Body ground Engine switch off Below 1 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I191-25 (GND) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

4.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)
NOTICE:

Before checking the millimeter wave radar sensor assembly beam axis deviation, check the installation condition of the millimeter wave radar sensor assembly.




c.

Connect the GTS to the DLC3.


d.

Turn the GTS on.


e.

Turn the cruise control switch (ON/OFF button) on.


f.

Enter the following menus: Powertrain / Radar Cruise / Utility / Beam Axis Misalignment Reading.


g.

Check the amount of misalignment and make a note.

Powertrain > Radar Cruise > Utility
Tester Display
Beam Axis Misalignment Reading
50005 239 4260

Result:
Result Proceed to
There is no beam axis misalignment A
There is a beam axis misalignment B



A

5.CHECK CAN COMMUNICATION SYSTEM

B

ADJUST MILLIMETER WAVE RADAR SENSOR BEAM AXIS

5.CHECK CAN COMMUNICATION SYSTEM
a.

Use the GTS to check if the CAN communication system is functioning normally.


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

6.CHECK FOR DTCS (PRE-CRASH 2)

B

6.CHECK FOR DTCS (PRE-CRASH 2)
a.

Check for DTCs and note any codes that are output.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

b.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

7.DATA LIST / ACTIVE TEST

B

7.DATA LIST / ACTIVE TEST

b.

Result:
Proceed to
NEXT



NEXT

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE