Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0163371 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Distance Control Switch Circuit  


DESCRIPTION

The distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the steering pad switch assembly (distance control switch) while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

A303849E24
1.271,1 2.802,1.188 1.531,0.188 10 false Distance Control Switch 0.969,2.604 2.896,2.854 1.927,0.25 10 false Steering Pad Switch Assembly 3.188,2.552 4.698,2.906 1.51,0.354 10 false Spiral Cable with Sensor Sub-assembly 5.594,2.448 5.906,2.646 0.313,0.198 10 false I191 5.594,2.615 6.615,3.469 1.021,0.854 10 false Driving Support ECU Assembly 2.531,0.729 3.146,0.927 0.615,0.198 10 false DIST 3.375,0.719 3.99,0.917 0.615,0.198 10 false DIST 3.802,0.719 4.417,0.917 0.615,0.198 10 false DIST 2.521,1.896 2.979,2.094 0.458,0.198 10 false ECC 3.365,1.896 3.823,2.094 0.458,0.198 10 false ECC 3.823,1.896 4.281,2.094 0.458,0.198 10 false ECC 3.031,0.844 3.344,1.042 0.313,0.198 10 false z3 3.031,2 3.344,2.198 0.313,0.198 10 false z3 4.26,2.01 4.719,2.208 0.458,0.198 10 false I28 4.26,0.854 4.719,1.052 0.458,0.198 10 false I28 5.708,0.865 6.323,1.063 0.615,0.198 10 false SPSW 5.521,0.74 5.677,0.938 0.156,0.198 10 false 6 4.26,0.646 4.573,0.844 0.313,0.198 10 false 12 4.302,1.792 4.458,1.99 0.156,0.198 10 false 2 3.063,0.625 3.219,0.823 0.156,0.198 10 false 4 3.063,1.792 3.219,1.958 0.156,0.167 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC)>PRECAUTION

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.READ VALUE ON GTS (DISTANCE CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Car Dist Time Setting Vehicle distance time setting condition No, Long, Mid, or Shrt Vehicle-to-vehicle distance selected by vehicle-to-vehicle distance control switch -
Powertrain > Radar Cruise > Data List
Tester Display
Car Dist Time Setting
50003 239 31
OK:

When the steering pad switch assembly (distance control switch) is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the I28 spiral cable sub-assembly connector.


b.

Disconnect the I191 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I28-12 (DIST) - I191-6 (SPSW) Always Below 1 Ω
I28-2 (ECC) - Body ground Always Below 1 Ω
I28-12 (DIST) or I191-6 (SPSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR