Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0163372 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  C1AAA  FCM Destination Information Uninitialized  C1AAD  Vehicle Information Initialization Incomplete  


DESCRIPTION

When the lane departure warning camera is replaced with a new one, it acquires the country specification information from the main body ECU (multiplex network body ECU) or ECM. If the lane departure warning camera cannot store the country specification information, DTC C1AAA or C1AAD is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAA FCM Destination Information Uninitialized While the engine switch is on (IG), the lane departure warning camera cannot store the country specification information.
·

Main body ECU (Multiplex network body ECU)

·

Lane departure warning camera


C1AAD Vehicle Information Initialization Incomplete When the engine switch is turned on (IG) or the system is activated, the vehicle information from the ECM cannot be confirmed.
·

ECM

·

Lane departure warning camera



CAUTION / NOTICE / HINT

NOTICE:
·

When the lane departure warning camera is replaced with a new one, adjustment of the lane departure warning camera axis must be performed

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT

·

When replacing the lane departure warning camera, always replace it with a new one. If a lane departure warning camera which was installed to another vehicle is used, the information stored in the lane departure warning camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

The lane departure alert system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshooting the lane departure alert system after confirming that the communication systems are functioning properly.



PROCEDURE

1.READ VALUE USING GTS (DESTINATION INFORMATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Lane Departure Alert / Data List.


e.

Read the Data List according to the display on the GTS.

Chassis > Lane Departure Alert > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Destination Information Status of the country JPN, NA, EURO, CHINA or OTHER (GEN-EXP) Actual country code -
Chassis > Lane Departure Alert > Data List
Tester Display
Destination Information
50003 355 6
Result:
Result Proceed to
Country specification information for vehicle and lane departure warning camera match A
Country specification information for vehicle and lane departure warning camera do not match B




A

2.CHECK FOR DTCS (LANE DEPARTURE ALERT SYSTEM)

B

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
2.CHECK FOR DTCS (LANE DEPARTURE ALERT SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Clear DTCs
50002 355

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Trouble Codes
50001 355
Result:
Result Proceed to
DTC C1AAA and C1AAD are not output A
DTC C1AAA or C1AAD is output B




A

B

3.REPLACE LANE DEPARTURE WARNING CAMERA
3.REPLACE LANE DEPARTURE WARNING CAMERA
a.

Replace the lane departure warning camera with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>REMOVAL


b.

Perform the lane departure warning camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCS (LANE DEPARTURE ALERT SYSTEM)
4.CHECK FOR DTCS (LANE DEPARTURE ALERT SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Clear DTCs
50002 355

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Trouble Codes
50001 355
Result:
Result Proceed to
DTC C1AAA and C1AAD are not output A
DTC C1AAA is output B
DTC C1AAD is output C




A

END (LANE DEPARTURE WARNING CAMERA WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCS (LANE DEPARTURE ALERT SYSTEM)
6.CHECK FOR DTCS (LANE DEPARTURE ALERT SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Clear DTCs
50002 355

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1AAA and C1AAD are not output A
DTC C1AAA is output B
DTC C1AAD is output C



A

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

B

C

7.REPLACE ECM
7.REPLACE ECM
a.

Replace the ECM with a new one.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTCS (LANE DEPARTURE ALERT SYSTEM)
8.CHECK FOR DTCS (LANE DEPARTURE ALERT SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Clear DTCs
50002 355

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1AAD is not output A
DTC C1AAD is output B



A

END (ECM WAS DEFECTIVE)

B