Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0163371 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

The millimeter wave radar sensor assembly and driving support ECU assembly transmit the data for general vehicle control and diagnosis function via CAN communication. The millimeter wave radar sensor assembly transmits information about the vehicle in front to the driving support ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor While dynamic radar cruise control is either preparing for operation or operating and engine switch is on (IG), communication between millimeter wave radar sensor assembly and driving support ECU assembly stops for 1 second or more.
·

Millimeter wave radar sensor assembly

·

Millimeter wave radar sensor circuit

·

Driving support ECU assembly



WIRING DIAGRAM

E287467E11
1.854,1.344 2.927,1.521 1.073,0.177 10 false ECU-IG1 NO. 3 5.979,0.427 6.281,0.677 0.302,0.25 10 false B 2.865,1.083 3.063,1.333 0.198,0.25 10 false 5 3.01,1.979 3.469,2.26 0.458,0.281 10 false SGND 2.865,1.875 3.021,2.094 0.156,0.219 10 false 1 3.885,1.281 4.344,1.563 0.458,0.281 10 false CA1P 5.958,1.281 6.417,1.563 0.458,0.281 10 false CA1P 3.885,1.896 4.344,2.177 0.458,0.281 10 false CA1N 5.958,1.885 6.417,2.167 0.458,0.281 10 false CA1N 4.344,1.094 4.542,1.323 0.198,0.229 10 false 3 4.333,1.688 4.531,1.917 0.198,0.229 10 false 2 5.74,1.135 5.938,1.365 0.198,0.229 10 false 40 5.719,1.729 5.917,1.958 0.198,0.229 10 false 18 5.719,2.302 6.052,2.552 0.333,0.25 10 false I191 5.719,2.448 7.01,3.063 1.292,0.615 10 false Driving Support ECU Assembly 2.917,2.375 3.25,2.625 0.333,0.25 10 false A79 2.917,2.531 4.375,3.198 1.458,0.667 10 false Millimeter Wave Radar Sensor Assembly 1.271,3.427 3.24,3.656 1.969,0.229 10 false : CAN Communication Line 3.74,0.438 5.115,0.646 1.375,0.208 10 false from IG1 NO. 3 Fuse 3.021,1.177 3.323,1.427 0.302,0.25 10 false IGB 5.729,0.344 5.927,0.573 0.198,0.229 10 false 30 0.313,1.177 1.302,1.615 0.99,0.438 10 false from IG1 NO. 3 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication is normal A
CAN communication is malfunctioning B



A

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)

B

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)
a.
A352224C01
1.458,0.229 1.875,0.49 0.417,0.26 2.021,1.135 2.396,0.688 2.396,0.688 2.667,0.688 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.552,0.281 2.01,0.479 0.458,0.198 10 false A79 2.729,0.604 3.188,0.802 0.458,0.198 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A79 millimeter wave radar sensor assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A79-5 (IGB) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the A79 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A79 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A79-1 (SGND) - Body ground Always Below 1 Ω



c.

Reconnect the A79 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

4.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
E244596C26
1.552,0.417 1.885,0.635 0.333,0.219 2.469,2.469 1.906,2.469 1.906,2.469 1.771,1.927 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 2.51,2.396 2.708,2.604 0.198,0.208 10 false B 1.594,0.438 1.927,0.604 0.333,0.167 10 false I191
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the I191 driving support ECU assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I191-30 (B) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the I191 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTCS (DTC U0235)
7.CHECK FOR DTCS (DTC U0235)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 239

d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -SET to activate the dynamic radar cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Powertrain > Radar Cruise > Trouble Codes
50001 239

g.

Turn the engine switch off.


Result:
Result Proceed to
DTCs are not output A
DTC U0235 is output B



A

END

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY