Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.04
RM19V0EQ _59 Vehicle Exterior _014621 LIGHTING (EXT) _0074248 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Daytime Running Light Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the daytime running lights.

WIRING DIAGRAM

E309224E22
0.51,0.865 1.781,1.094 1.271,0.229 10 false from Battery 0.365,1.302 1.781,1.51 1.417,0.208 10 false from ALT Fuse 2.708,2.656 4.125,3.052 1.417,0.396 10 false Engine Room Junction Block Assembly 4.469,1.25 6.083,1.656 1.615,0.406 10 false Instrument Panel Junction Block Assembly 5.385,3.771 7.031,4.365 1.646,0.594 10 false Main Body ECU (Multiplex Network Body ECU) 2.438,4.281 3.844,4.813 1.406,0.531 10 false Daytime Running Light Assembly LH 2.427,5.948 3.833,6.49 1.406,0.542 10 false Daytime Running Light Assembly RH 2.813,0.896 3.333,1.115 0.521,0.219 10 false BATT 2.813,1.333 3.333,1.552 0.521,0.219 10 false ALT 2.813,1.75 3.333,1.969 0.521,0.219 10 false GND1 2.813,2.198 3.333,2.417 0.521,0.219 10 false GND2 6.156,0.896 6.677,1.115 0.521,0.219 10 false DRL 2.438,4.104 2.958,4.323 0.521,0.219 10 false A86 2.427,5.781 2.948,6 0.521,0.219 10 false A85 2.625,3.604 2.813,3.813 0.188,0.208 10 false 1 3.76,3.604 3.948,3.813 0.188,0.208 10 false 2 3.76,5.281 3.948,5.49 0.188,0.208 10 false 2 2.625,5.281 2.813,5.49 0.188,0.208 10 false 1 2.823,3.719 3.01,3.927 0.188,0.208 10 false E 3.573,3.719 3.76,3.927 0.188,0.208 10 false B 2.813,5.375 3,5.583 0.188,0.208 10 false E 3.573,5.385 3.76,5.594 0.188,0.208 10 false B 2.5,0.688 2.688,0.896 0.188,0.208 10 false 1 2.5,1.104 2.688,1.313 0.188,0.208 10 false 1 2.5,1.542 2.688,1.75 0.188,0.208 10 false 3 2.5,1.99 2.688,2.198 0.188,0.208 10 false 4 3.906,0.688 4.094,0.896 0.188,0.208 10 false 6 2.5,0.896 2.688,1.104 0.188,0.208 10 false A 2.5,1.323 2.688,1.531 0.188,0.208 10 false B 2.458,1.75 2.698,1.958 0.24,0.208 10 false 1F 2.448,2.177 2.698,2.375 0.25,0.198 10 false 1G 3.875,0.906 4.115,1.115 0.24,0.208 10 false 1F 3.854,2.333 4.104,2.531 0.25,0.198 10 false 1G 4.979,0.896 5.219,1.104 0.24,0.208 10 false 3D 4.99,0.708 5.208,0.917 0.219,0.208 10 false 23 5.896,0.802 6.135,1.01 0.24,0.208 10 false 25 3.302,0.896 3.823,1.115 0.521,0.219 10 false DRLS 3.323,2.333 3.844,2.552 0.521,0.219 10 false LDRL 3.917,2.146 4.104,2.354 0.188,0.208 10 false 8 5.385,3.604 5.906,3.823 0.521,0.219 10 false MB

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Daytime Running Light Daytime running lights ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Daytime Running Light
50004 123 63
OK:

The daytime running lights illuminate.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
2.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Using a voltmeter, check the signal reading of the engine room junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION

OK:

Output signal reading is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)

NG

INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)

3.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)
a.

Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


E230000C16
4.75,2.646 5.083,2.844 0.333,0.198 2.792,2.646 3.125,2.844 0.333,0.198 0.74,2.646 1.073,2.844 0.333,0.198 6.167,2.646 6.5,2.844 0.333,0.198 0.885,3.563 0.771,3.99 false 2.625,3.646 2.5,4.094 false 6.292,3.604 6.177,4.052 false 5.115,3.646 5.229,4.094 false 4.833,2.667 5.042,2.833 0.208,0.167 10 false 1G 2.896,2.667 3.094,2.833 0.198,0.167 10 false 1F 0.875,2.667 1,2.833 0.125,0.167 10 false B 0.896,0.396 1.115,0.563 0.219,0.167 10 false *a 0.646,4.01 0.979,4.198 0.333,0.188 10 false ALT 6.302,2.667 6.438,2.833 0.135,0.167 10 false A 2.375,4.104 2.833,4.292 0.458,0.188 10 false GND1 6.042,4.063 6.5,4.25 0.458,0.188 10 false BATT 5.125,4.104 5.729,4.417 0.604,0.313 10 false GND2
*a Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly)
- -


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-1 (BATT) - Body ground Always 11 to 14 V
B-1 (ALT) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-3 (GND1) - Body ground Always Below 1 Ω
1G-4 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-6 (DRLS) - 3D-23 Always Below 1 Ω
3D-23 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.
E182506C12
1.479,0.771 1.969,1.063 0.49,0.292 1.479,2.938 1.969,3.229 0.49,0.292 2.531,3.49 2.531,3.75 false 0.167,0.156 0.5,0.5 0.333,0.344 10 false *a 1.646,0.833 2.073,1.333 0.427,0.5 10 false 3D 1.625,3 2.042,3.313 0.417,0.313 10 false MB 2.406,3.771 2.948,4.302 0.542,0.531 10 false DRL
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-23 - MB-25 (DRL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - DAYTIME RUNNING LIGHT ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - DAYTIME RUNNING LIGHT ASSEMBLY)
a.

Disconnect the A86 daytime running light assembly LH connector.


b.

Disconnect the A85 daytime running light assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-8 (LDRL) - A86-2 (B) Always Below 1 Ω
1G-8 (LDRL) - A85-2 (B) Always Below 1 Ω
1G-8 (LDRL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Replace the engine room junction block assembly with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Check that the daytime running lights operate normally.

OK:

The daytime running lights operate normally.



Result:
Proceed to
OK
NG



OK

END (ENGINE ROOM JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)