Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.04
RM19V0EQ _58 Vehicle Interior _014608 METER / GAUGE / DISPLAY _0074143 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge malfunction via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1500 Fuel Sender Open Detected When IG voltage is 9.5 V or more and the following condition is detected:
1.

Fuel sender gauge operation malfunction


·

Harness or connector

·

Fuel sender gauge assembly

·

Combination meter assembly


- -

WIRING DIAGRAM

E156126E58
5.313,2.99 7.146,3.333 1.833,0.344 10 false Combination Meter Assembly 6.063,0.896 6.469,1.208 0.406,0.313 10 false FR 6.063,2.24 6.542,2.531 0.479,0.292 10 false FE 5.635,0.719 5.958,1.156 0.323,0.438 10 false 18*1 14*2 5.656,2.052 5.99,2.531 0.333,0.479 10 false 17*1 15*2 2.104,2.24 2.667,2.646 0.563,0.406 10 false 3 2.125,0.885 2.458,1.167 0.333,0.281 10 false 2 0.344,3.135 2.26,3.49 1.917,0.354 10 false Fuel Sender Gauge Assembly 0.49,1.542 1.115,2.292 0.625,0.75 10 false Fuel Sender Gauge Assembly 1.292,1.427 1.656,1.771 0.365,0.344 10 false 2 1.292,2.094 1.604,2.333 0.313,0.24 10 false 1 1.802,2.24 2.292,2.573 0.49,0.333 10 false FE 1.823,0.885 2.229,1.188 0.406,0.302 10 false FS 5.323,2.844 5.771,3.146 0.448,0.302 10 false I18 0.333,2.969 0.906,3.365 0.573,0.396 10 false N11 2.708,3.083 5.125,3.344 2.417,0.26 10 false *1: w/o Multi-information Display 2.719,3.396 5.135,3.656 2.417,0.26 10 false *2: w/ Multi-information Display

PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input signal Min.: 0 L, Max.: 127.5 L Fuel receiver gauge indicates F: 62.9
Fuel receiver gauge indicates 3/4: 54.5
Fuel receiver gauge indicates 1/2: 35.0
Fuel receiver gauge indicates 1/4: 15.4
Fuel receiver gauge indicates E: 7.0
Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data can be displayed on the GTS and DTC B1500 is output. A
Fuel level data cannot be displayed on the GTS. B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.INSPECT FUEL SENDER GAUGE ASSEMBLY
2.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
E224284C44
0.292,1.677 0.771,1.979 0.479,0.302 1.104,2.135 1.104,2.573 1.104,2.573 0.938,2.573 false 1.604,2.156 1.604,2.719 1.604,2.719 1.833,2.719 false 1.229,2.146 1.229,2.792 1.229,2.792 1.042,2.792 false 1.479,2.156 1.479,3.063 1.479,3.063 1.313,3.063 false 0.417,1.74 0.833,2.042 0.417,0.302 10 false I18 0.188,0.167 0.406,0.333 0.219,0.167 10 false *a 1.896,2.625 2.542,2.833 0.646,0.208 10 false FR*A 0.573,2.479 1,2.667 0.427,0.188 10 false FR*B 0.677,2.698 1.417,2.969 0.74,0.271 10 false FE*B 0.948,2.979 1.688,3.25 0.74,0.271 10 false FE*A
*A w/o Multi-information Display
*B w/ Multi-information Display
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the I18 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Multi-information Display
Tester Connection Condition Specified Condition
I18-18 (FR) - I18-17 (FE) Always 13.5 to 414.5 Ω

w/ Multi-information Display
Tester Connection Condition Specified Condition
I18-14 (FR) - I18-15 (FE) Always 13.5 to 414.5 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
a.

Disconnect the N11 fuel suction tube assembly with pump and gauge connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Multi-information Display
Tester Connection Condition Specified Condition
I18-18 (FR) - N11-2 (FS) Always Below 1 Ω
I18-18 (FR) - Body ground Always 10 kΩ or higher
I18-17 (FE) - N11-3 (FE) Always Below 1 Ω
I18-17 (FE) - Body ground Always 10 kΩ or higher

w/ Multi-information Display
Tester Connection Condition Specified Condition
I18-14 (FR) - N11-2 (FS) Always Below 1 Ω
I18-14 (FR) - Body ground Always 10 kΩ or higher
I18-15 (FE) - N11-3 (FE) Always Below 1 Ω
I18-15 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
a.

Visually check for deformation on the fuel suction tube assembly with pump and gauge connector.

OK:

There is no deformation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE