Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.04
RM19V0EQ _58 Vehicle Interior _014608 METER / GAUGE / DISPLAY _0074143 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The meter ECU uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge will vary between approximately 13 Ω with the float at the full position, and 414 Ω with the float at the empty position. The meter outputs battery voltage through two resistors that are mounted inside the meter ECU. The meter ECU measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of the battery voltage.

HINT:

The fuel level warning light will come on when the fuel level is below 10.5 liters (11.1 US qts, 9.2 Imp. qts).


WIRING DIAGRAM

E156126E58
5.313,2.99 7.146,3.333 1.833,0.344 10 false Combination Meter Assembly 6.063,0.896 6.469,1.208 0.406,0.313 10 false FR 6.063,2.24 6.542,2.531 0.479,0.292 10 false FE 5.635,0.719 5.958,1.156 0.323,0.438 10 false 18*1 14*2 5.656,2.052 5.99,2.531 0.333,0.479 10 false 17*1 15*2 2.104,2.24 2.667,2.646 0.563,0.406 10 false 3 2.125,0.885 2.458,1.167 0.333,0.281 10 false 2 0.344,3.135 2.26,3.49 1.917,0.354 10 false Fuel Sender Gauge Assembly 0.49,1.542 1.115,2.292 0.625,0.75 10 false Fuel Sender Gauge Assembly 1.292,1.427 1.656,1.771 0.365,0.344 10 false 2 1.292,2.094 1.604,2.333 0.313,0.24 10 false 1 1.802,2.24 2.292,2.573 0.49,0.333 10 false FE 1.823,0.885 2.229,1.188 0.406,0.302 10 false FS 5.323,2.844 5.771,3.146 0.448,0.302 10 false I18 0.333,2.969 0.906,3.365 0.573,0.396 10 false N11 2.708,3.083 5.125,3.344 2.417,0.26 10 false *1: w/o Multi-information Display 2.719,3.396 5.135,3.656 2.417,0.26 10 false *2: w/ Multi-information Display

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full, Sender F -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Meter Operation
50004 122 3
OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FUEL INPUT)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0 L, Max.: 127.5 L Fuel receiver gauge indicates F: 62.9
Fuel receiver gauge indicates 3/4: 54.5
Fuel receiver gauge indicates 1/2: 35.0
Fuel receiver gauge indicates 1/4: 15.4
Fuel receiver gauge indicates E: 7.0
Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data displayed on the GTS is almost same as the fuel receiver gauge indication. A
Fuel level data displayed on the GTS differs from the fuel receiver gauge indication. B



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)

B

REPLACE COMBINATION METER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
a.

Disconnect the I18 combination meter assembly and N11 fuel suction tube assembly with pump and gauge connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Multi-information Display
Tester Connection Condition Specified Condition
I18-18 (FR) - N11-2 (FS) Always Below 1 Ω
I18-18 (FR) - Body ground Always 10 kΩ or higher
I18-17 (FE) - N11-3 (FE) Always Below 1 Ω
I18-17 (FE) - Body ground Always 10 kΩ or higher

w/ Multi-information Display
Tester Connection Condition Specified Condition
I18-14 (FR) - N11-2 (FS) Always Below 1 Ω
I18-14 (FR) - Body ground Always 10 kΩ or higher
I18-15 (FE) - N11-3 (FE) Always Below 1 Ω
I18-15 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
a.

Visually check for deformation on the fuel suction tube assembly with pump and gauge connector.

OK:

There is no deformation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE