Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING › from 2015.04
RM19V0EQ _59 Vehicle Exterior _014623 EXTERIOR PANELS / TRIM _0074276 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL REAR DOOR REAR WINDOW FRAME MOULDING

a.
B381024

Using an air riveter or hand riveter with a nose piece, install the rear door rear window frame moulding with 4 new rivets.

HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
·
B125583C21
1.333,0.24 1.479,0.24 1.479,0.24 1.802,0.719 false 1.844,1.281 1.844,1.802 false 2.333,0.052 2.729,0.458 0.396,0.406 10 false *c 1.177,0.146 1.542,0.49 0.365,0.344 10 false *a 1.792,1.823 2.083,2.063 0.292,0.24 10 false *b
*a Riveter
*b Mandrel
*c Incorrect


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B125584C19
1.438,0.448 1.156,0.448 false 1.458,1.417 1.219,1.417 false 2.323,0.083 2.688,0.406 0.365,0.323 10 false *b 2.333,1.094 2.708,1.448 0.375,0.354 10 false *b 1.458,0.354 2,0.698 0.542,0.344 10 false *a 1.479,1.323 1.979,1.667 0.5,0.344 10 false *a
*a Riveter
*b Incorrect


Confirm that the rivets are seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.

·
B125585C17
1.146,0.719 1.406,0.719 false 2.448,0.313 2.74,0.719 0.292,0.406 10 false *b 1.427,0.625 1.99,1.042 0.563,0.417 10 false *a
*a Riveter
*b Incorrect


Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.




Hide 75764A 2.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING

a.
B381022

Engage the guide of the rear door upper window frame moulding to the door frame.


b.

Using an air riveter or hand riveter with a nose piece, install the rear door upper window frame moulding with 4 new rivets.

HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
·
B125583C21
1.333,0.24 1.479,0.24 1.479,0.24 1.802,0.719 false 1.844,1.281 1.844,1.802 false 2.333,0.052 2.729,0.458 0.396,0.406 10 false *c 1.177,0.146 1.542,0.49 0.365,0.344 10 false *a 1.792,1.823 2.083,2.063 0.292,0.24 10 false *b
*a Riveter
*b Mandrel
*c Incorrect


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B125584C19
1.438,0.448 1.156,0.448 false 1.458,1.417 1.219,1.417 false 2.323,0.083 2.688,0.406 0.365,0.323 10 false *b 2.333,1.094 2.708,1.448 0.375,0.354 10 false *b 1.458,0.354 2,0.698 0.542,0.344 10 false *a 1.479,1.323 1.979,1.667 0.5,0.344 10 false *a
*a Riveter
*b Incorrect


Confirm that the rivets are seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.

·
B125585C17
1.146,0.719 1.406,0.719 false 2.448,0.313 2.74,0.719 0.292,0.406 10 false *b 1.427,0.625 1.99,1.042 0.563,0.417 10 false *a
*a Riveter
*b Incorrect


Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.




Hide 75762A 3.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:

When installing a new rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Door Front Window Frame Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or rear door front window frame moulding excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any remaining double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the vehicle body and a new rear door front window frame moulding.


c.

Remove the release paper from the rear door front window frame moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B381020C01
1.25,1.479 1.667,1.479 true 1.677,2.26 2.094,2.26 true 2.125,2.167 2.458,2.5 0.333,0.333 10 false *a 1.073,1.385 1.406,1.719 0.333,0.333 10 false *a
*a Caulking Sponge
V100155

Double-sided Tape


Engage the clip and guide, and attach the double-sided tape and caulking sponge to install the rear door front window frame moulding.

HINT:

Press the rear door front window frame moulding firmly to install it.



Hide 75740 4.INSTALL REAR DOOR BELT MOULDING ASSEMBLY

Hide 68104 5.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Hide 68124B 6.INSTALL REAR DOOR QUARTER WINDOW GLASS

Hide 67408F 7.INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

Hide 68152C 8.INSTALL REAR DOOR GLASS RUN

Hide 67872 9.INSTALL REAR DOOR WEATHERSTRIP

Hide 68640A 10.INSTALL REAR DOOR CHECK ASSEMBLY

Hide 67842E 11.INSTALL REAR DOOR SERVICE HOLE COVER

Hide 68174A 12.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

Hide 67604 13.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74260 14.INSTALL REAR ARMREST ASSEMBLY

Hide 15.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 69284D 16.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION