Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › from 2015.04
RM19V0EQ _59 Vehicle Exterior _014618 DOOR / HATCH _0074223 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75978H 2.INSTALL REAR DOOR LOWER OUTSIDE STRIPE

Hide 5.INSTALL REAR DOOR REAR WINDOW FRAME MOULDING

Hide 75764A 6.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING

Hide 75762A 7.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

Hide 75740 8.INSTALL REAR DOOR BELT MOULDING ASSEMBLY

Hide 67003C 9.INSTALL REAR DOOR PANEL CUSHION

a.
B281693

Engage the 2 claws to install 2 new rear door panel cushions.


Hide 67888F 10.INSTALL REAR DOOR NO. 2 WEATHERSTRIP

a.
B281741

Engage the 5 clips to install the rear door No. 2 weatherstrip.


Hide 69204A 11.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B280438C07
0.688,1.698 0.365,1.792 false 0.198,1.719 0.49,1.979 0.292,0.26 10 false *1 0.083,0.083 0.5,0.417 0.417,0.333 10 false *a 0.083,2.083 0.677,2.5 0.594,0.417 10 false *b
*1 Door Handle Nut
*a Outside
*b Inside


Engage the claw.


c.

Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw and door handle nut.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 12.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B280436

Engage the 2 claws to install the rear door rear outside handle pad.


Hide 69241G 13.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B280435

Engage the 3 claws to install the rear door front outside handle pad.


Hide 69240 14.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B280434

Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

NOTICE:

If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.



b.

Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.


Hide 69250G 15.INSTALL REAR DOOR OUTSIDE HANDLE COVER ASSEMBLY

a.
B280431

Engage the claw and install the rear door outside handle cover assembly.


b.

Using a T30 "TORX" socket wrench, install the rear door outside handle cover assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69780B 16.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B280430

Install the rear door inside locking cable assembly.


b.
B280428

Engage the 3 claws.


Hide 69740D 17.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B280426

Install the rear door lock remote control cable assembly.


b.
B280424

Engage the claw.


Hide 69060A 18.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing the removed rear door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door with motor lock assembly.



a.

Apply MP grease to the sliding parts of the rear door lock with motor assembly.


b.

When reusing the rear door with motor lock assembly:

i.
B280422

Install a new door lock wiring harness seal to the rear door lock with motor assembly.



c.
B280421C11
3.146,2.906 2.979,2.844 false 3.177,2.844 3.427,3.042 0.25,0.198 10 false *1
*1 Release Plate


Insert the rear door lock with motor assembly to the rear door outside handle release plate, and set it to the rear door panel.


d.

Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock with motor assembly.


e.

Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 85720E 19.INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.


a.
B280419

Using a T25 "TORX" socket wrench, install the rear power window regulator motor assembly with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

When replacing the rear window regulator, a new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



Hide 20.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.

Install the temporary bolt to the rear door window regulator assembly.


c.
B280418C13
1.021,0.302 1.823,0.5 false 2.396,1.271 2.677,1.552 false 0.854,0.219 1.104,0.469 0.25,0.25 10 false *1 2.677,1.552 2.99,1.844 0.313,0.292 10 false (1) 2.708,0.594 3.073,0.896 0.365,0.302 10 false (2) 2.688,1.104 3.031,1.417 0.344,0.313 10 false (3) 0.656,0.219 1.042,0.583 0.385,0.365 10 false (4)
*1 Temporary Bolt


Temporarily install the rear door window regulator assembly.


d.

Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



Hide 67674A 21.INSTALL REAR DOOR FRAME GARNISH

a.
B280403

Engage the clip to install a new rear door frame garnish.


Hide 69975A 22.INSTALL REAR DOOR GLASS CHANNEL FILLER

a.

Apply soapy water to a new rear door glass channel filler.


b.
B280415C06
0.74,1.135 0.365,0.938 false 2.375,1.125 2.813,0.917 false 0.031,0.021 0.531,0.438 0.5,0.417 12 false *A 3.177,0.021 3.427,0.344 0.25,0.323 12 false *B 0.646,0.542 1.073,0.844 0.427,0.302 10 false *a 2.271,0.552 2.615,0.823 0.344,0.271 10 false *b 2.833,0.813 3.177,1.063 0.344,0.25 10 false *c 0.198,0.823 0.573,1.083 0.375,0.26 10 false *c
*A Front Side
*B Rear Side
*a 4.57 mm (0.180 in.)
*b 4.8 mm (0.189 in.)
*c Edge of curved surface


Install the rear door glass channel filler to the position shown in the illustration.


Hide 69906B 23.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY

a.

Apply soapy water to the channel filler side of the rear door glass channel sub-assembly.


b.
B280416C06
0.75,1.135 0.448,0.948 false 2.354,1.125 2.719,0.917 false 0.083,0.031 0.531,0.313 0.448,0.281 12 false *A 3.156,0.021 3.427,0.396 0.271,0.375 12 false *B 0.677,0.521 0.969,0.813 0.292,0.292 10 false *a 2.26,0.531 2.604,0.823 0.344,0.292 10 false *b 2.76,0.792 3.083,1.052 0.323,0.26 10 false *c 0.281,0.823 0.667,1.031 0.385,0.208 10 false *c
*A Front Side
*B Rear Side
*a 4.57 mm (0.180 in.)
*b 4.8 mm (0.189 in.)
*c Edge of curved surface


Using a plastic hammer, install the rear door glass channel sub-assembly to the position shown in the illustration.

NOTICE:

To prevent damaging the rear door glass subassembly, be careful not to strike the channel with too much force.



Hide 68104 24.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.
B281694

Slide the rear door glass sub-assembly to install it as shown in the illustration.


Hide 68124B 25.INSTALL REAR DOOR QUARTER WINDOW GLASS

a.

Install the rear door quarter window glass to the rear door quarter window weatherstrip.


b.
B280411

Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.


Hide 67408F 26.INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

a.
B280409

Install the rear door lower window frame sub-assembly with the screw and 2 bolts.


Hide 68152C 27.INSTALL REAR DOOR GLASS RUN

a.
B280408

Install the rear door glass run.


Hide 67872 28.INSTALL REAR DOOR WEATHERSTRIP

a.
B281691

Engage the 20 clips to install the rear door weatherstrip.


Hide 68640A 29.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door check assembly.


b.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
B280406

Install the rear door check assembly with the 2 nuts and bolt.

Torque:
Bolt : 29 N*m (296 kgf*cm, 21 ft.*lbf)
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67842E 30.INSTALL REAR DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the rear door panel.


b.
B281695C03
0.365,0.281 0.552,0.333 false 3.01,0.448 2.844,0.5 false 1.625,3.042 1.813,3.104 false 0.198,0.167 0.5,0.438 0.302,0.271 10 false *1 3.01,0.344 3.302,0.594 0.292,0.25 10 false *1 1.844,3.01 2.24,3.25 0.396,0.24 10 false *1
*1 Reference Point


Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.


c.

Attach the rear door service hole cover according to the reference points on the rear door panel.

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.



d.

Connect the connector.


Hide 68174A 31.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

a.
B280401

Install the rear door inner glass weatherstrip.


Hide 69206C 32.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B277194

Engage the guide and 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.


Hide 67604 33.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B280402

Install the No. 1 door scuff plate clamp as shown in the illustration.


b.
B280397C07
3.094,0.771 2.625,1.125 false 2.26,1.729 2.479,1.51 false 3.125,0.635 3.427,0.927 0.302,0.292 10 false *1 2.083,1.719 2.365,2.021 0.281,0.302 10 false *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly


Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.


c.

Connect the connector.


d.

Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.

B334515C05
1,1.917 1.188,1.833 false 0.854,1.823 1.167,2.021 0.313,0.198 10 false *1
*1 Reference Boss - -



e.
B280393

Engage the 8 clips and install the rear door trim board sub-assembly.


f.

Install the 3 screws.


g.

If protective tape has been applied, remove it.


Hide 74260 34.INSTALL REAR ARMREST ASSEMBLY

a.
B280392

Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.


Hide 35.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.

Connect the connector.


b.
B280390

Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.


Hide 69284D 36.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B288541

Engage the 3 claws to install the rear door inside handle bezel plug.


Hide 37.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION