Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.04
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module (Sensor Bus)  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

·

The driving support ECU assembly will store this DTC when no signals are received from the ECUs that have been memorized as those that are connected to sub bus 13.

·

When the driving support ECU assembly receives a response signal from the ECUs connected to sub bus 13, the driving support ECU assembly recognizes and memorizes that the ECU is connected to sub bus 13. Based on this memorized data, the driving support ECU assembly monitors for malfunctions in the ECUs connected to sub bus 13 when communicating with those ECUs. If the driving support ECU assembly does not receive response signals from the ECUs that have been memorized as those connected to sub bus 13, the driving support ECU assembly determines that a malfunction exists.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0235 Lost Communication with Cruise Control Front Distance Range Sensor No communication from the millimeter wave radar sensor assembly continues.
·

Open or short in sub bus 13 main line or connector

·

Millimeter wave radar sensor assembly

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit


The driving support ECU assembly stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 13.
U1002 Lost Communication with Gateway Module (Sensor Bus) The driving support ECU assembly does not receive signals from all ECUs that have been memorized as those connected to sub bus 13.
·

Open or short in sub bus 13 main line or connector

·

Driving support ECU assembly

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Millimeter wave radar sensor assembly

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit


The driving support ECU assembly stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 13.

HINT:

The diagnostic procedure is for when DTC U1002 is output by the driving support ECU assembly (GTS display: Pre-Crash 2).


WIRING DIAGRAM

C260169E09
5.063,1.146 7.063,1.521 2,0.375 10 false Driving Support ECU Assembly 5.063,3.469 6.927,3.948 1.865,0.479 10 false Millimeter Wave Radar Sensor Assembly 3.521,0.865 4.135,1.156 0.615,0.292 10 false 120 Ω 3.552,3.99 4.167,4.281 0.615,0.292 10 false 120 Ω 2.927,1.573 3.313,1.75 0.385,0.177 10 false CA1P 4.188,1.583 4.688,1.76 0.5,0.177 10 false CA1N 2.875,3.302 3.313,3.479 0.438,0.177 10 false CA1P 4.188,3.302 4.604,3.479 0.417,0.177 10 false CA1N 3.125,1.771 3.292,1.948 0.167,0.177 10 false 40 4.188,1.771 4.354,1.948 0.167,0.177 10 false 18 3.208,3.094 3.375,3.271 0.167,0.177 10 false 3 4.198,3.083 4.365,3.26 0.167,0.177 10 false 2 4.74,1.146 5.25,1.458 0.51,0.313 10 false I191 4.75,3.469 5.271,3.76 0.521,0.292 10 false A79 1.104,4.708 2.979,5.052 1.875,0.344 10 false : CAN Main Bus Line (CANH) 1.104,5.104 2.979,5.448 1.875,0.344 10 false : CAN Main Bus Line (CANL) 5.052,0.177 6.635,0.594 1.583,0.417 10 false x: Suspected Area 3.052,2.083 3.292,2.313 0.24,0.229 10 false LG 3.115,2.823 3.333,3.052 0.219,0.229 10 false B 4.271,2.823 4.49,3.052 0.219,0.229 10 false W 4.271,2.094 4.49,2.323 0.219,0.229 10 false W 0.083,0.052 1.104,0.292 1.021,0.24 12 false Sub Bus 13:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

Body Electrical > Gateway > Trouble Codes
50001 150

Result:
Result Proceed to
DTC U0104 not output from network gateway ECU (GTS display: Gateway) A
DTC U0104 is output from network gateway ECU (GTS display: Gateway) B



A

2.CHECK SUB BUS 13

B

GO TO DIAGNOSTIC PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK SUB BUS 13
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.
C287804C12
1.531,2.698 1.875,2.969 0.344,0.271 1.521,0.063 1.906,0.333 0.385,0.271 2.083,4.438 2.354,4.438 2.354,4.438 2.354,4.01 true 0.5,1.083 0.5,0.198 0.5,0.198 0.688,0.198 true 0.552,1.333 0.552,2.24 0.552,2.24 0.74,2.24 true 2.313,2.271 2.198,2.271 2.198,2.271 2.198,1.333 true 0.125,2.708 0.438,2.906 0.313,0.198 10 false *1 1.615,2.729 1.927,2.927 0.313,0.198 10 false I39 1.771,4.333 2.229,4.531 0.458,0.198 10 false BAT 1.594,0.094 2.063,0.385 0.469,0.292 10 false I191 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 0.813,2.135 1.427,2.333 0.615,0.198 10 false CA1P 0.771,0.104 1.385,0.302 0.615,0.198 10 false CA1N 2.375,2.167 2.833,2.365 0.458,0.198 10 false GND
*1 DLC3
*a Component with harness connected
(Driving Support ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I191-40 (CA1P) - I191-18 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in main bus lines
I191-40 (CA1P) - I191-25 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I191-18 (CA1N) - I191-25 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I191-40 (CA1P) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I191-18 (CA1N) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus lines) B
NG (Short circuit between bus lines) C
·

NG (Ground short)

·

NG (+B short)


D



A

3.CHECK FOR POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

B

7.CHECK FOR OPEN IN SUB BUS 13 MAIN LINES (DRIVING SUPPORT ECU ASSEMBLY)

C

9.CHECK FOR SHORT IN SUB BUS 13 LINES (DRIVING SUPPORT ECU ASSEMBLY)

D

11.CHECK FOR SHORT IN SUB BUS 13 LINE (DRIVING SUPPORT ECU ASSEMBLY)
3.CHECK FOR POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Check the millimeter wave radar sensor assembly power source circuit.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>Millimeter Wave Radar Sensor Power Source Circuit


Result:
Result
OK
NG



OK

4.CHECK FOR DTC OUTPUT

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

4.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON.


h.

Check for DTCs.

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1002 is not output from the driving support ECU assembly (GTS display: Pre-Crash 2) A
DTC U1002 is output from the driving support ECU assembly (GTS display: Pre-Crash 2) B



A

B

5.REPLACE DRIVING SUPPORT ECU ASSEMBLY
5.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL


Result:
Result
NEXT



NEXT

6.CHECK FOR DTC OUTPUT
6.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs.

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1002 is not output from the driving support ECU assembly (GTS display: Pre-Crash 2) A
DTC U1002 is output from the driving support ECU assembly (GTS display: Pre-Crash 2) B



A

END

B

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

7.CHECK FOR OPEN IN SUB BUS 13 MAIN LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.
E251017C92
0.667,0.698 1.094,0.979 0.427,0.281 2.292,2.583 2.469,2.583 2.469,2.583 2.823,1.938 true 2.677,0.948 2.781,0.948 2.781,0.948 2.854,1.719 true 1.885,2.49 2.552,2.708 0.667,0.219 10 false CA1P 2.281,0.844 3.198,1.042 0.917,0.198 10 false CA1N 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.74,0.75 1.208,1.052 0.469,0.302 10 false I191
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I191-40 (CA1P) - I191-18 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

8.CHECK FOR OPEN IN SUB BUS 13 MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
8.CHECK FOR OPEN IN SUB BUS 13 MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Reconnect the driving support ECU assembly connector.


b.
C316812C05
1.479,0.208 1.906,0.479 0.427,0.271 0.792,0.646 1.042,0.646 1.042,0.646 1.531,1.104 true 2.604,0.635 2.365,0.635 2.365,0.635 1.688,1.104 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.563,0.271 2.021,0.469 0.458,0.198 10 false A79 0.396,0.573 1.01,0.771 0.615,0.198 10 false CA1N 2.677,0.563 3.292,0.76 0.615,0.198 10 false CA1P
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A79-3 (CA1P) - A79-2 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR

9.CHECK FOR SHORT IN SUB BUS 13 LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.
E251017C93
0.667,0.698 1.094,0.979 0.427,0.281 2.292,2.583 2.469,2.583 2.469,2.583 2.823,1.938 true 2.677,0.948 2.781,0.948 2.781,0.948 2.854,1.719 true 1.885,2.49 2.552,2.708 0.667,0.219 10 false CA1P 2.281,0.844 3.198,1.042 0.917,0.198 10 false CA1N 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.74,0.75 1.344,1.094 0.604,0.344 10 false I191
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I191-40 (CA1P) - I191-18 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

10.CHECK FOR SHORT IN SUB BUS 13 LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
10.CHECK FOR SHORT IN SUB BUS 13 LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Reconnect the driving support ECU assembly connector.


b.
C316812C06
1.479,0.208 1.906,0.479 0.427,0.271 0.792,0.646 1.042,0.646 1.042,0.646 1.531,1.104 true 2.604,0.635 2.365,0.635 2.365,0.635 1.688,1.104 true 0.073,0.094 0.385,0.25 0.313,0.156 10 false *a 1.563,0.271 2.021,0.469 0.458,0.198 10 false A79 0.396,0.573 1.01,0.771 0.615,0.198 10 false CA1N 2.677,0.563 3.292,0.76 0.615,0.198 10 false CA1P
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A79-3 (CA1P) - A79-2 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR

11.CHECK FOR SHORT IN SUB BUS 13 LINE (DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the driving support ECU assembly connector.


b.
C287806C11
1.5,0.208 1.875,0.458 0.375,0.25 1.521,2.49 1.885,2.729 0.365,0.24 2.885,1.427 2.885,0.542 2.885,0.542 2.698,0.542 true 2.854,1.635 2.854,2.229 2.854,2.229 2.667,2.229 true 1.323,1.625 1.323,2.188 1.323,2.188 1.135,2.188 true 2.354,3.667 2.354,4.219 2.354,4.219 2.167,4.219 true 1.563,0.24 2.115,0.542 0.552,0.302 10 false I191 0.177,2.563 0.49,2.76 0.313,0.198 10 false *1 2.281,0.458 2.896,0.656 0.615,0.198 10 false CA1N 2.26,2.135 2.875,2.333 0.615,0.198 10 false CA1P 0.781,2.104 1.24,2.302 0.458,0.198 10 false GND 1.615,2.521 1.927,2.719 0.313,0.198 10 false I39 1.844,4.146 2.313,4.385 0.469,0.24 10 false BAT 0.177,0.365 0.49,0.563 0.313,0.198 10 false *a
*1 DLC3
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I191-40 (CA1P) - I191-25 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I191-18 (CA1N) - I191-25 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I191-40 (CA1P) - I39-16(BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I191-18 (CA1N) - I39-16(BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 13 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 13 inspection.

·

If the resistance changes to normal when the connector is disconnected from the ECU, there may be a short in the ECU.




Result:
Result
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

12.CHECK FOR SHORT IN SUB BUS 13 LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
12.CHECK FOR SHORT IN SUB BUS 13 LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Reconnect the driving support ECU assembly connector.


b.
C287387C15
1.5,0.24 1.885,0.521 0.385,0.281 1.5,2.688 1.917,3 0.417,0.313 1.698,1.479 2.146,0.875 2.146,0.875 2.271,0.875 true 1.083,0.896 1.24,0.896 1.24,0.896 1.552,1.5 true 1.781,4.375 1.906,4.375 1.906,4.375 2.354,3.948 true 1.635,3.427 2.167,2.99 2.167,2.99 2.333,2.99 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.573,0.302 2.073,0.625 0.5,0.323 10 false A79 0.677,0.781 1.292,0.979 0.615,0.198 10 false CA1N 2.333,0.771 2.948,0.969 0.615,0.198 10 false CA1P 0.083,2.448 0.396,2.646 0.313,0.198 10 false *1 1.615,2.729 1.927,2.927 0.313,0.198 10 false I39 2.406,2.896 2.719,3.094 0.313,0.198 10 false CG 1.469,4.271 1.927,4.469 0.458,0.198 10 false BAT
*1 DLC3
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
A79-3 (CA1P) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
A79-2 (CA1N) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
A79-3 (CA1P) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
A79-2 (CA1N) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 13 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 13 inspection.

·

If the resistance changes to normal when the connector is disconnected from the ECU, there may be a short in the ECU.




Result:
Result
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR