Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.04
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U023A  Lost Communication with Front Camera Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U023A Lost Communication with Front Camera Module No communication from the lane departure warning camera continues.
·

Lane departure warning camera branch line or connector

·

Power source circuit of lane departure warning camera

·

Lane departure warning camera ground circuit

·

Lane departure warning camera


The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.

HINT:

The diagnostic procedure is for when DTC U023A is output by the network gateway ECU (GTS display: Gateway).


WIRING DIAGRAM

C325234E01
5.802,2.688 5.167,0.917 5.167,0.917 4.885,0.917 true 5.26,2.688 4.646,1.302 4.646,1.302 4.323,1.302 true 4.792,2.688 4.26,1.708 4.26,1.708 3.906,1.708 true 3.958,2.677 3.635,2.104 3.635,2.104 3.344,2.104 true 0.063,0.052 3.729,0.292 3.667,0.24 12 false Sub Bus 2 (for RHD): 0.063,4.198 1.188,4.594 1.125,0.396 10 false Network Gateway ECU 6.177,3.604 6.948,3.802 0.771,0.198 10 false 120 Ω 0.563,3.594 1.333,3.792 0.771,0.198 10 false 120 Ω 1.958,1.615 4.073,1.854 2.115,0.24 10 false CAN No. 9 Junction Connector 1.385,2.01 3.5,2.25 2.115,0.24 10 false CAN No. 8 Junction Connector 2.385,1.208 4.5,1.448 2.115,0.24 10 false CAN No. 5 Junction Connector 2.948,0.823 5.063,1.063 2.115,0.24 10 false CAN No. 6 Junction Connector 5.844,4.24 7.094,4.646 1.25,0.406 10 false CAN No. 7 Junction Connector 1.146,5.188 1.74,5.563 0.594,0.375 10 false ECU-IG1 NO. 2 1.813,4.938 1.969,5.135 0.156,0.198 10 false 7 2.01,5.042 2.469,5.24 0.458,0.198 10 false IGB 3.031,5.021 3.49,5.219 0.458,0.198 10 false GND 3.427,4.927 3.74,5.125 0.313,0.198 10 false 11 2.323,4.479 2.479,4.677 0.156,0.198 10 false 6 2.917,4.49 3.229,4.688 0.313,0.198 10 false 12 2.219,4.708 2.833,4.906 0.615,0.198 10 false CA1P 2.75,4.708 3.365,4.906 0.615,0.198 10 false CA1N 1.688,5.49 2.146,5.688 0.458,0.198 10 false S14 0.177,5.208 1.583,5.573 1.406,0.365 10 false Trouble Area 1.969,5.49 4.115,5.75 2.146,0.26 10 false Lane Departure Warning Camera 1.438,6.188 3.385,6.479 1.948,0.292 10 false : CAN Main Bus Line (CANH) 1.438,6.479 3.438,6.719 2,0.24 10 false : CAN Main Bus Line (CANL) 4.417,6.188 6.302,6.427 1.885,0.24 10 false : CAN Branch Line (CANH) 4.417,6.5 6.25,6.74 1.833,0.24 10 false : CAN Branch Line (CANL)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 52 seconds, and then drive the vehicle at a speed of 1 km/h (1 mph) or more for 7 second or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

Body Electrical > Gateway > Trouble Codes
50001 150
HINT:

If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.



Result:
Result Proceed to
DTC U1002 is not output from the network gateway ECU (GTS display: Gateway) A
DTC U1002 is output from the network gateway ECU (GTS display: Gateway) B



A

2.CHECK FOR OPEN IN SUB BUS LINES (LANE DEPARTURE WARNING CAMERA BRANCH LINE)

B

GO TO DIAGNOSTIC PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS LINES (LANE DEPARTURE WARNING CAMERA BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C325172C03
1.51,0.208 1.969,0.469 0.458,0.26 2.177,1.115 2.49,0.729 2.49,0.729 2.656,0.729 true 2.156,1.458 2.448,1.854 2.448,1.854 2.615,1.854 true 2.74,0.646 3.292,0.885 0.552,0.24 10 false CA1P 0.146,0.104 0.698,0.344 0.552,0.24 10 false *a 2.708,1.76 3.26,2 0.552,0.24 10 false CA1N 1.625,0.25 2.01,0.49 0.385,0.24 10 false S14
*a Front view of wire harness connector
(to Lane Departure Warning Camera)


Disconnect the lane departure warning camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S14-6 (CA1P) - S14-12 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (LANE DEPARTURE WARNING CAMERA)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C325172C04
1.51,0.208 1.969,0.469 0.458,0.26 0.771,1.844 1.031,1.844 1.031,1.844 1.344,1.469 true 2,1.458 2.292,1.854 2.292,1.854 2.458,1.854 true 0.479,1.771 1.031,2.01 0.552,0.24 10 false IGB 0.146,0.104 0.698,0.344 0.552,0.24 10 false *a 2.542,1.76 3.094,2 0.552,0.24 10 false GND 1.625,0.25 2.01,0.49 0.385,0.24 10 false S14
*a Front view of wire harness connector
(to Lane Departure Warning Camera)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S14-11 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S14-7 (IGB) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)