Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2015.04–2016.05
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module (Network Gateway ECU)  


DESCRIPTION

·

The network gateway ECU will store this DTC when no signals are received from the ECUs that have been memorized as those that are connected to sub bus 2.

·

When the network gateway ECU receives a response signal from the ECUs connected to sub bus 2, the network gateway ECU recognizes and memorizes that the ECU is connected to sub bus 2. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to sub bus 2 when communicating with those ECUs. If the network gateway ECU does not receive response signals from the ECUs that have been memorized as those connected to sub bus 2, the network gateway ECU determines that a malfunction exists.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U1002 Lost Communication with Gateway Module (Network Gateway ECU) The network gateway ECU does not receive signals from all ECUs that have been memorized as those connected to sub bus 2.
·

Open or short in sub bus 2 main lines or connector

·

Short in sub bus 2 branch lines or connector

·

Network gateway ECU

(w/ Parking Assist Monitor System or Pre-crash Safety System)

·

Blind spot monitor sensor RH

(w/ Pre-crash Safety System)

·

Rear television camera assembly

(w/ Parking Assist Monitor System or Pre-crash Safety System)

·

Driving support ECU assembly

(w/ Pre-crash Safety System)

·

Lane departure warning camera

(w/ Pre-crash Safety System)

·

Open or short in CAN No. 5 junction connector

(w/ Parking Assist Monitor System or Pre-crash Safety System)

·

Open or short in CAN No. 6 junction connector

(w/ Parking Assist Monitor System or Pre-crash Safety System)

·

Open or short in CAN No. 7 junction connector

(w/ Parking Assist Monitor System or Pre-crash Safety System)

·

Open or short in CAN No. 8 junction connector

(w/ Pre-crash Safety System)

·

Open or short in CAN No. 9 junction connector

(w/ Parking Assist Monitor System or Pre-crash Safety System)


The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.

HINT:

This diagnosis procedure is for when DTC U1002 is output by the network gateway ECU (GTS display: Gateway).


WIRING DIAGRAM

C325229E10
0.781,0.531 1.396,0.729 0.615,0.198 10 false I160 1.104,0.531 2.771,0.781 1.667,0.25 10 false Network Gateway ECU 4.104,0.865 4.719,1.063 0.615,0.198 10 false CA2H 2.667,0.875 3.281,1.073 0.615,0.198 10 false CA2L 4.094,1.125 4.406,1.323 0.313,0.198 10 false 13 2.948,1.125 3.26,1.323 0.313,0.198 10 false 12 4.146,1.323 4.302,1.521 0.156,0.198 10 false B 2.865,1.323 3.177,1.521 0.313,0.198 10 false LG 4.229,1.521 4.385,1.719 0.156,0.198 10 false 1 2.875,1.521 3.031,1.719 0.156,0.198 10 false 2 4.229,2.385 4.385,2.583 0.156,0.198 10 false 1 2.875,2.375 3.031,2.573 0.156,0.198 10 false 2 3.875,1.531 4.49,1.729 0.615,0.198 10 false I178 3.083,1.531 3.698,1.729 0.615,0.198 10 false I178 3.073,2.365 3.688,2.563 0.615,0.198 10 false I179 3.865,2.354 4.479,2.552 0.615,0.198 10 false I179 4.125,2.688 4.281,2.885 0.156,0.198 10 false V 2.875,2.698 3.188,2.896 0.313,0.198 10 false LG 4.135,3.104 4.292,3.302 0.156,0.198 10 false V 2.896,3.094 3.052,3.292 0.156,0.198 10 false B 4.083,3.271 4.396,3.469 0.313,0.198 10 false 11 2.927,3.271 3.24,3.469 0.313,0.198 10 false 22 4.073,4.458 4.229,4.656 0.156,0.198 10 false 8 2.938,4.469 3.25,4.667 0.313,0.198 10 false 19 4.094,4.75 4.25,4.948 0.156,0.198 10 false G 2.948,4.74 3.104,4.938 0.156,0.198 10 false B 0.938,1.969 2.927,2.177 1.99,0.208 10 false CAN No. 9 Junction Connector 0.917,5.521 2.906,5.729 1.99,0.208 10 false CAN No. 6 Junction Connector 0.896,3.875 2.969,4.125 2.073,0.25 10 false CAN No. 5 Junction Connector 0.656,7.063 2.781,7.354 2.125,0.292 10 false CAN No. 7 Junction Connector 4.063,4.969 4.219,5.167 0.156,0.198 10 false 3 2.958,4.969 3.271,5.167 0.313,0.198 10 false 14 4.365,5.344 4.521,5.542 0.156,0.198 10 false 2 4.333,5.813 4.646,6.01 0.313,0.198 10 false 13 4.083,6.146 4.24,6.344 0.156,0.198 10 false 1 2.958,6.135 3.271,6.333 0.313,0.198 10 false 12 5.625,5.323 5.781,5.521 0.156,0.198 10 false 4 5.625,5.813 5.781,6.01 0.156,0.198 10 false 1 5.813,5.813 6.427,6.01 0.615,0.198 10 false CANL 5.813,5.333 6.427,5.531 0.615,0.198 10 false CANH 4.104,6.74 4.719,6.938 0.615,0.198 10 false CANH 2.698,6.729 3.313,6.927 0.615,0.198 10 false CANL 4.094,6.51 4.25,6.708 0.156,0.198 10 false 3 3.021,6.51 3.177,6.708 0.156,0.198 10 false 2 4.948,5.25 5.104,5.448 0.156,0.198 10 false V 4.969,5.896 5.125,6.094 0.156,0.198 10 false P 4.094,6.323 4.25,6.521 0.156,0.198 10 false L 2.979,6.313 3.135,6.51 0.156,0.198 10 false B 1.427,8.115 3.375,8.323 1.948,0.208 10 false : CAN Main Bus Line (CANH) 1.427,8.438 3.385,8.708 1.958,0.271 10 false : CAN Main Bus Line (CANL) 4.729,8.115 6.781,8.438 2.052,0.323 10 false : CAN Branch Line (CANH) 4.729,8.458 6.552,8.729 1.823,0.271 10 false : CAN Branch Line (CANL) 0.646,5.521 1.104,5.719 0.458,0.198 10 false T17 0.385,7.063 0.844,7.26 0.458,0.198 10 false T18 0.604,3.875 1.063,4.073 0.458,0.198 10 false O31 4.406,3.469 4.719,3.667 0.313,0.198 10 false LG 5.813,4.26 6.271,4.458 0.458,0.198 10 false CB+ 5.813,4.604 6.427,4.802 0.615,0.198 10 false CGND 5.615,4.167 5.771,4.365 0.156,0.198 10 false 6 5.615,4.708 5.771,4.906 0.156,0.198 10 false 5 5.552,2.354 5.865,2.552 0.313,0.198 10 false 11 5.563,1.833 5.875,2.031 0.313,0.198 10 false 23 5.5,2.688 6.115,2.885 0.615,0.198 10 false I194 5.833,2.271 6.292,2.469 0.458,0.198 10 false CA+ 5.833,1.948 6.448,2.146 0.615,0.198 10 false CGND 5.802,2.688 7.094,3.104 1.292,0.417 10 false Navigation Receiver Assembly 5.583,6.177 6.042,6.375 0.458,0.198 10 false T22 5.875,6.177 7.031,6.667 1.156,0.49 10 false Rear Television Camera Assembly 0.115,0.083 1.771,0.323 1.656,0.24 12 false Sub Bus 2 (for LHD): 3.417,0.427 4.188,0.625 0.771,0.198 10 false 120 Ω 3.417,7.292 4.188,7.49 0.771,0.198 10 false 120 Ω 4.958,0.281 6.729,0.646 1.771,0.365 10 false x: Suspected Area 5.344,3.479 5.5,3.677 0.156,0.198 10 false L

C325230E02
0.073,0.083 1.781,0.365 1.708,0.281 12 false Sub Bus 2 (for RHD): 0.75,0.583 1.365,0.781 0.615,0.198 10 false I160 1.063,0.583 2.625,0.865 1.563,0.281 10 false Network Gateway ECU 4.104,0.76 4.719,0.958 0.615,0.198 10 false CA2H 2.677,0.771 3.292,0.969 0.615,0.198 10 false CA2L 4.052,1.021 4.365,1.219 0.313,0.198 10 false 13 2.969,1.021 3.281,1.219 0.313,0.198 10 false 12 4.177,1.198 4.333,1.396 0.156,0.198 10 false B 2.844,1.198 3.156,1.396 0.313,0.198 10 false LG 5.969,2.313 7.063,2.833 1.094,0.521 10 false Lane Departure Warning Camera 4.083,1.354 4.24,1.552 0.156,0.198 10 false 3 3.021,1.354 3.177,1.552 0.156,0.198 10 false 9 4.344,1.448 4.5,1.646 0.156,0.198 10 false 1 4.354,2.063 4.51,2.26 0.156,0.198 10 false 7 5.031,1.385 5.188,1.583 0.156,0.198 10 false V 5,2.135 5.313,2.333 0.313,0.198 10 false LG 5.615,1.469 5.771,1.667 0.156,0.198 10 false 6 5.563,2.073 5.833,2.271 0.271,0.198 10 false 12 5.813,1.458 6.427,1.656 0.615,0.198 10 false CA1P 5.813,2.073 6.427,2.271 0.615,0.198 10 false CA1N 5.667,2.313 6.125,2.51 0.458,0.198 10 false S14 1.563,1.521 2.813,2 1.25,0.479 10 false CAN No. 8 Junction Connector 4.073,2.188 4.229,2.385 0.156,0.198 10 false 2 3.031,2.188 3.188,2.385 0.156,0.198 10 false 8 4.177,2.406 4.333,2.604 0.156,0.198 10 false R 2.865,2.406 3.177,2.604 0.313,0.198 10 false LG 2.573,3.333 3.188,3.531 0.615,0.198 10 false I192 3.865,2.698 4.479,2.896 0.615,0.198 10 false I193 3.073,2.698 3.688,2.896 0.615,0.198 10 false I193 2.573,2.969 3.188,3.167 0.615,0.198 10 false I192 3.854,3.594 4.469,3.792 0.615,0.198 10 false I179 3.073,3.594 3.688,3.792 0.615,0.198 10 false I179 4.365,3.083 6.427,3.354 2.063,0.271 10 false CAN No. 9 Junction Connector 2.104,2.75 2.26,2.948 0.156,0.198 10 false L 2.073,3.542 2.385,3.74 0.313,0.198 10 false LG 1.49,2.823 1.802,3.021 0.313,0.198 10 false 39 1.479,3.458 1.792,3.656 0.313,0.198 10 false 17 1.031,2.833 1.646,3.031 0.615,0.198 10 false CA2H 1.042,3.479 1.656,3.677 0.615,0.198 10 false CA2L 0.073,3.698 0.688,3.896 0.615,0.198 10 false I191 0.385,3.698 1.396,4.208 1.01,0.51 10 false Driving Support ECU Assembly 4.198,2.656 4.354,2.854 0.156,0.198 10 false 1 4.219,3.604 4.375,3.802 0.156,0.198 10 false 1 2.656,2.771 2.813,2.969 0.156,0.198 10 false 1 2.865,2.667 3.021,2.865 0.156,0.198 10 false 2 2.885,3.625 3.042,3.823 0.156,0.198 10 false 2 2.646,3.542 2.802,3.74 0.156,0.198 10 false 2 4.188,3.865 4.344,4.063 0.156,0.198 10 false V 2.875,3.854 3.188,4.052 0.313,0.198 10 false LG 4.188,4.25 4.344,4.448 0.156,0.198 10 false V 2.948,4.26 3.104,4.458 0.156,0.198 10 false B 4.083,4.438 4.396,4.635 0.313,0.198 10 false 11 2.938,4.448 3.25,4.646 0.313,0.198 10 false 22 4.083,5.271 4.24,5.469 0.156,0.198 10 false 8 2.958,5.271 3.271,5.469 0.313,0.198 10 false 19 4.083,5.708 4.24,5.906 0.156,0.198 10 false 3 2.958,5.708 3.271,5.906 0.313,0.198 10 false 14 4.146,5.49 4.302,5.688 0.156,0.198 10 false G 2.948,5.49 3.104,5.688 0.156,0.198 10 false B 4.354,4.531 4.51,4.729 0.156,0.198 10 false 9 4.344,5.167 4.656,5.365 0.313,0.198 10 false 20 5.031,4.458 5.188,4.656 0.156,0.198 10 false R 5.031,5.25 5.188,5.448 0.156,0.198 10 false B 5.615,4.542 5.771,4.74 0.156,0.198 10 false 2 5.625,5.156 5.781,5.354 0.156,0.198 10 false 7 5.802,4.542 6.417,4.74 0.615,0.198 10 false CA1P 5.813,5.167 6.427,5.365 0.615,0.198 10 false CA1N 5.635,5.396 6.094,5.594 0.458,0.198 10 false O32 5.948,5.396 7.115,5.823 1.167,0.427 10 false Blind Spot Monitor Sensor RH 0.906,4.771 2.969,5.042 2.063,0.271 10 false CAN No. 5 Junction Connector 4.635,6.135 6.698,6.406 2.063,0.271 10 false CAN No. 6 Junction Connector 0.625,7.448 2.688,7.719 2.063,0.271 10 false CAN No. 7 Junction Connector 0.604,4.771 1.063,4.969 0.458,0.198 10 false O31 4.354,6.135 4.813,6.333 0.458,0.198 10 false T17 0.354,7.448 0.813,7.646 0.458,0.198 10 false T18 4.083,7.115 4.698,7.313 0.615,0.198 10 false CANH 2.74,7.115 3.354,7.313 0.615,0.198 10 false CANL 0.073,6.698 0.531,6.896 0.458,0.198 10 false T22 0.333,6.698 1.5,7.198 1.167,0.5 10 false Rear Television Camera Assembly 1.479,5.854 1.635,6.052 0.156,0.198 10 false 4 1.469,6.479 1.625,6.677 0.156,0.198 10 false 1 0.979,5.865 1.594,6.063 0.615,0.198 10 false CANH 1,6.479 1.615,6.677 0.615,0.198 10 false CANL 2.083,5.76 2.24,5.958 0.156,0.198 10 false V 2.083,6.583 2.24,6.781 0.156,0.198 10 false P 2.698,5.844 2.854,6.042 0.156,0.198 10 false 2 2.656,6.458 2.969,6.656 0.313,0.198 10 false 13 4.083,6.594 4.24,6.792 0.156,0.198 10 false 1 2.938,6.594 3.198,6.802 0.26,0.208 10 false 12 4.094,6.917 4.25,7.115 0.156,0.198 10 false 3 3,6.917 3.156,7.115 0.156,0.198 10 false 2 3.417,0.292 4.188,0.49 0.771,0.198 10 false 120 Ω 3.406,7.677 4.177,7.875 0.771,0.198 10 false 120 Ω 4.188,6.76 4.344,6.958 0.156,0.198 10 false L 2.958,6.75 3.115,6.948 0.156,0.198 10 false B 1.406,8.104 3.438,8.354 2.031,0.25 10 false : CAN Main Bus Line (CANH) 1.406,8.458 3.448,8.688 2.042,0.229 10 false : CAN Main Bus Line (CANL) 4.708,8.104 6.542,8.406 1.833,0.302 10 false : CAN Branch Line (CANH) 4.708,8.458 6.479,8.74 1.771,0.281 10 false : CAN Branch Line (CANL) 1.271,1.521 1.729,1.719 0.458,0.198 10 false S15 5.177,0.229 6.542,0.51 1.365,0.281 10 false x: Suspected Area

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure (for LHD): Turn the ignition switch to ON, wait at least 22 seconds.

·

DTC check procedure (for RHD): Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 52 seconds, and then drive the vehicle at a speed of 5 km/h (3 mph) or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK SUB BUS 2

B

25.CHECK SUB BUS 2
2.CHECK SUB BUS 2
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C238893C06
1.51,0.677 1.99,0.969 0.479,0.292 1.656,1.667 1.938,2.135 1.938,2.135 2.198,2.135 false 1.552,1.677 1.292,2.146 1.292,2.146 1.031,2.146 false 2.042,1.51 2.406,0.813 2.406,0.813 2.646,0.813 false 1.385,1.51 1.042,0.823 1.042,0.823 0.802,0.823 false 0.063,0.031 0.26,0.208 0.198,0.177 10 false *a 0.656,2.063 1.448,2.271 0.792,0.208 10 false CA2H 2.229,2.052 2.885,2.25 0.656,0.198 10 false CA2L 2.698,0.74 3.375,0.927 0.677,0.188 10 false BATT 0.49,0.76 1.198,0.979 0.708,0.219 10 false GND 1.604,0.74 1.958,0.938 0.354,0.198 10 false I160
*a Component with harness connected
(Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in a main bus line
I160-13 (CA2H) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I160-12 (CA2L) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I160-13 (CA2H) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I160-12 (CA2L) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus line B
Short circuit between bus lines C
·

Ground short

·

+B short


D



A

3.CHECK FOR OPEN IN SUB BUS 2 LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)

B

8.CHECK FOR OPEN IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)

C

13.CHECK FOR SHORT IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)

D

19.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 9 JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN SUB BUS 2 LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)
a.

Disconnect the rear television camera assembly connector.


b.
C294680C31
1.573,0.188 1.958,0.479 0.385,0.292 0.979,1.958 1.146,1.958 1.146,1.958 1.563,1.417 true 0.99,0.563 1.135,0.563 1.135,0.563 1.552,1.156 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.646,0.229 2.104,0.427 0.458,0.198 10 false T22 0.583,0.469 1.198,0.667 0.615,0.198 10 false CANL 0.563,1.865 1.177,2.063 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T22-4 (CANH) - T22-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

4.CHECK FOR DTC OUTPUT

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (CAN NO. 6 JUNCTION CONNECTOR - REAR TELEVISION CAMERA ASSEMBLY)

4.CHECK FOR DTC OUTPUT
a.

Reconnect the rear television camera assembly connector.


b.

Reconnect the cable to the negative (-) battery terminal.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / IPA/Parking Assist Monitor / Trouble Codes.


Result:
Result Proceed to
DTC C1621 is not output from the rear television camera assembly (GTS display: IPA/Parking Assist Monitor) A
DTC C1621 is output from the rear television camera assembly (GTS display: IPA/Parking Assist Monitor) B



A

5.CHECK FOR DTC OUTPUT

B

5.CHECK FOR DTC OUTPUT
a.

Enter the following menus: Body Electrical / Gateway / Trouble Codes.

Body Electrical > Gateway > Trouble Codes
50001 150

Result:
Result Proceed to
DTC U1002 is not output from the network gateway ECU (GTS display: Gateway) A
DTC U1002 is output from the network gateway ECU (GTS display: Gateway) B



A

B

6.REPLACE NETWORK GATEWAY ECU
6.REPLACE NETWORK GATEWAY ECU
a.

Replace the network gateway ECU.

Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU>REMOVAL


Result:
Result
NEXT



NEXT

7.CHECK FOR DTC OUTPUT
7.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Gateway / Trouble Codes.

Body Electrical > Gateway > Trouble Codes
50001 150

Result:
Result Proceed to
DTC U1002 is not output from the network gateway ECU (GTS display: Gateway) A
Other DTC is output
DTC U1002 is output from the network gateway ECU (GTS display: Gateway)
B



A

END

B

REPLACE REAR TELEVISION CAMERA ASSEMBLY

8.CHECK FOR OPEN IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)
a.
C238892C39
0.479,1.146 0.865,1.365 0.385,0.219 1.844,1.51 1.844,1.792 1.844,1.792 1.667,1.792 false 1.958,1.51 1.958,1.802 1.958,1.802 2.156,1.802 false 0.115,0 0.365,0.24 0.25,0.24 10 false *a 2.188,1.74 2.896,1.938 0.708,0.198 10 false CA2H 1.313,1.74 2.021,1.917 0.708,0.177 10 false CA2L 0.542,1.167 0.823,1.365 0.281,0.198 10 false I160
*a Front view of wire harness connector
(to Network Gateway ECU)


Disconnect the network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

9.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 9 JUNCTION CONNECTOR)
9.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 9 JUNCTION CONNECTOR)
a.

Reconnect the network gateway ECU connector.


b.

Disconnect the I178 and I179 wire harness connectors.


c.
C310106C01
0.115,1.635 0.552,1.906 0.438,0.271 2.073,1.719 2.51,1.99 0.438,0.271 0.323,2.313 0.219,2.125 true 0.656,2.896 0.427,2.427 true 1.021,2.708 0.542,2.365 true 0.542,2.208 0.802,1.99 true 1.448,2.323 1.177,2.26 true 1.646,2.927 1.552,2.427 true 1.698,2.198 2.167,2.198 true 1.698,2.365 2.219,2.677 true 0.063,0.073 0.375,0.271 0.313,0.198 10 false *a 0.875,1.896 1.792,2.094 0.917,0.198 10 false CANH*b 0.833,2.729 1.75,2.927 0.917,0.198 10 false CANL*b 2.208,2.125 3.125,2.323 0.917,0.198 10 false CANH*c 2.271,2.604 3.188,2.802 0.917,0.198 10 false CANL*c 0.198,1.698 0.813,1.896 0.615,0.198 10 false I178 2.156,1.771 2.771,1.969 0.615,0.198 10 false I179 0.073,2.042 0.229,2.24 0.156,0.198 10 false B 0.583,2.927 0.896,3.125 0.313,0.198 10 false LG 1.031,2.188 1.188,2.385 0.156,0.198 10 false V 1.583,2.958 1.896,3.156 0.313,0.198 10 false LG
*a Rear view of wire harness connector
(to CAN No. 9 Junction Connector)
*b to Network Gateway ECU
*c to CAN No. 5 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
I178-1 (CANH) - I178-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Network gateway ECU
I179-1 (CANH) - I179-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 5 junction connector



Result:
Result Proceed to
OK A
NG (to network gateway ECU main bus line) B
NG (to CAN No. 5 junction connector main bus line) C



A

REPLACE CAN NO. 9 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 9 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

C

10.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 5 JUNCTION CONNECTOR)
10.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 5 JUNCTION CONNECTOR)
a.

Reconnect the I178 and I179 wire harness connectors.


b.

Disconnect the wire harness connector from the CAN No. 5 junction connector.


c.
C238890C88
0.469,1.24 0.958,1.5 0.49,0.26 2.5,0.51 1.969,0.51 1.969,0.51 1.969,1.354 false 2.646,0.771 2.323,0.771 2.323,0.771 2.323,1.354 false 2.646,1.885 2.323,1.885 2.323,1.885 2.323,1.573 false 1.802,2.031 1.969,2.031 1.969,2.031 1.969,1.573 false 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.573,0.427 3.125,0.583 0.552,0.156 10 false CANH*b 2.677,0.688 3.229,0.844 0.552,0.156 10 false CANH*c 1.281,1.948 1.833,2.104 0.552,0.156 10 false CANL*b 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*c 0.552,1.281 0.833,1.479 0.281,0.198 10 false O31
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 6 Junction Connector
*c to CAN No. 9 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
O31-8 (CANH) - O31-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 6 junction connector
O31-11 (CANH) - O31-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 9 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 9 junction connector main bus line) B
NG (to CAN No. 6 junction connector main bus line) C



A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 9 JUNCTION CONNECTOR)

C

11.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 6 JUNCTION CONNECTOR)
11.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 6 JUNCTION CONNECTOR)
a.

Reconnect the wire harness connector to the CAN No. 5 junction connector.


b.

Disconnect the wire harness connector from the CAN No. 6 junction connector.


c.
C238890C89
1.021,0.281 1.5,0.531 0.479,0.25 0.75,1.219 0.927,1.219 0.927,1.219 1.135,1.406 true 0.688,0.708 0.917,0.708 0.917,0.708 1.385,1.365 true 1.719,1.885 1.396,1.885 1.396,1.885 1.396,1.573 true 0.698,1.656 0.958,1.656 0.958,1.656 1.167,1.563 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 0.208,1.135 0.76,1.292 0.552,0.156 10 false CANH*b 0.135,0.625 0.688,0.781 0.552,0.156 10 false CANH*c 0.167,1.583 0.719,1.74 0.552,0.156 10 false CANL*b 1.781,1.802 2.333,1.958 0.552,0.156 10 false CANL*c 1.125,0.323 1.406,0.531 0.281,0.208 10 false T17
*a Front view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 7 Junction Connector
*c to CAN No. 5 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
T17-1 (CANH) - T17-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 7 junction connector
T17-3 (CANH) - T17-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 5 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 5 junction connector main bus line) B
NG (to CAN No. 7 junction connector main bus line) C



A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

12.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 7 JUNCTION CONNECTOR)
12.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 7 JUNCTION CONNECTOR)
a.

Reconnect the wire harness connector to the CAN No. 6 junction connector.


b.

Disconnect the wire harness connector from the CAN No. 7 junction connector.


c.
C183982C14
1.781,2.063 2.198,2.302 0.417,0.24 0.948,0.844 0.646,0.844 0.646,0.844 0.646,2.177 false 1.24,1.177 0.938,1.177 0.938,1.177 0.938,2.167 false 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 1,0.75 1.573,0.906 0.573,0.156 10 false CANH*b 1.292,1.094 1.854,1.25 0.563,0.156 10 false CANL*b 1.844,2.094 2.115,2.26 0.271,0.167 10 false T18
*a Rear view of wire harness connector
(to CAN No. 7 Junction Connector)
*b to CAN No. 6 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T18-3 (CANH) - T18-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 6 JUNCTION CONNECTOR - CAN NO. 7 JUNCTION CONNECTOR)

13.CHECK FOR SHORT IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)
a.
C238892C39
0.479,1.146 0.865,1.365 0.385,0.219 1.844,1.51 1.844,1.792 1.844,1.792 1.667,1.792 false 1.958,1.51 1.958,1.802 1.958,1.802 2.156,1.802 false 0.115,0 0.365,0.24 0.25,0.24 10 false *a 2.188,1.74 2.896,1.938 0.708,0.198 10 false CA2H 1.313,1.74 2.021,1.917 0.708,0.177 10 false CA2L 0.542,1.167 0.823,1.365 0.281,0.198 10 false I160
*a Front view of wire harness connector
(to Network Gateway ECU)


Disconnect the network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

14.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 9 JUNCTION CONNECTOR)
14.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 9 JUNCTION CONNECTOR)
a.

Reconnect the network gateway ECU connector.


b.

Disconnect the I178 and I179 wire harness connectors.


c.
C310106C01
0.115,1.635 0.552,1.906 0.438,0.271 2.073,1.719 2.51,1.99 0.438,0.271 0.323,2.313 0.219,2.125 true 0.656,2.896 0.427,2.427 true 1.021,2.708 0.542,2.365 true 0.542,2.208 0.802,1.99 true 1.448,2.323 1.177,2.26 true 1.646,2.927 1.552,2.427 true 1.698,2.198 2.167,2.198 true 1.698,2.365 2.219,2.677 true 0.063,0.073 0.375,0.271 0.313,0.198 10 false *a 0.875,1.896 1.792,2.094 0.917,0.198 10 false CANH*b 0.833,2.729 1.75,2.927 0.917,0.198 10 false CANL*b 2.208,2.125 3.125,2.323 0.917,0.198 10 false CANH*c 2.271,2.604 3.188,2.802 0.917,0.198 10 false CANL*c 0.198,1.698 0.813,1.896 0.615,0.198 10 false I178 2.156,1.771 2.771,1.969 0.615,0.198 10 false I179 0.073,2.042 0.229,2.24 0.156,0.198 10 false B 0.583,2.927 0.896,3.125 0.313,0.198 10 false LG 1.031,2.188 1.188,2.385 0.156,0.198 10 false V 1.583,2.958 1.896,3.156 0.313,0.198 10 false LG
*a Rear view of wire harness connector
(to CAN No. 9 Junction Connector)
*b to Network Gateway ECU
*c to CAN No. 5 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
I178-1 (CANH) - I178-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Network gateway ECU
I179-1 (CANH) - I179-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 5 junction connector



Result:
Result Proceed to
OK A
NG (to network gateway ECU main bus line) B
NG (to CAN No. 5 junction connector main bus line) C



A

REPLACE CAN NO. 9 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 9 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

C

15.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 5 JUNCTION CONNECTOR)
15.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 5 JUNCTION CONNECTOR)
a.

Reconnect the I178 and I179 wire harness connectors.


b.

Disconnect the wire harness connector from the CAN No. 5 junction connector.


c.
C238890C88
0.469,1.24 0.958,1.5 0.49,0.26 2.5,0.51 1.969,0.51 1.969,0.51 1.969,1.354 false 2.646,0.771 2.323,0.771 2.323,0.771 2.323,1.354 false 2.646,1.885 2.323,1.885 2.323,1.885 2.323,1.573 false 1.802,2.031 1.969,2.031 1.969,2.031 1.969,1.573 false 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.573,0.427 3.125,0.583 0.552,0.156 10 false CANH*b 2.677,0.688 3.229,0.844 0.552,0.156 10 false CANH*c 1.281,1.948 1.833,2.104 0.552,0.156 10 false CANL*b 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*c 0.552,1.281 0.833,1.479 0.281,0.198 10 false O31
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 6 Junction Connector
*c to CAN No. 9 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
O31-8 (CANH) - O31-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 6 junction connector
O31-11 (CANH) - O31-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 9 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 9 junction connector main bus line) B
NG (to CAN No. 6 junction connector main bus line) C



A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 9 JUNCTION CONNECTOR)

C

16.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 6 JUNCTION CONNECTOR)
16.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 6 JUNCTION CONNECTOR)
a.

Reconnect the wire harness connector to the CAN No. 5 junction connector.


b.

Disconnect the wire harness connector from the CAN No. 6 junction connector.


c.
C238890C91
1.531,0.094 2.01,0.354 0.479,0.26 0.813,0.646 0.979,0.646 0.979,0.646 1.396,1.365 true 1.781,2.063 1.385,2.063 1.385,2.063 1.385,1.573 true 1.281,1.385 1,0.938 1,0.938 0.771,0.938 true 1.281,1.573 1.281,1.979 1.281,1.979 1.021,1.979 true 0.677,1.24 0.854,1.24 0.854,1.24 1.135,1.385 true 0.698,1.677 0.979,1.677 0.979,1.677 1.167,1.573 true 0.052,0.042 0.292,0.25 0.24,0.208 10 false *a 0.135,1.156 0.688,1.313 0.552,0.156 10 false CANH*b 0.229,0.854 0.781,1.01 0.552,0.156 10 false CANH*c 0.146,1.604 0.698,1.76 0.552,0.156 10 false CANL*b 0.51,1.906 1.063,2.063 0.552,0.156 10 false CANL*c 1.823,1.979 2.375,2.135 0.552,0.156 10 false CANL*d 0.271,0.563 0.823,0.719 0.552,0.156 10 false CANH*d 1.625,0.156 1.896,0.375 0.271,0.219 10 false T17
*a Front view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 7 Junction Connector
*c to Rear Television Camera Assembly
*d to CAN No. 5 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
T17-1 (CANH) - T17-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 7 junction connector
T17-2 (CANH) - T17-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Rear television camera assembly
T17-3 (CANH) - T17-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 5 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 5 junction connector main bus line) B
NG (to CAN No. 7 junction connector main bus line) C
NG (to rear television camera assembly) D



A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

17.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 7 JUNCTION CONNECTOR)

D

18.CHECK FOR SHORT IN SUB BUS 2 LINES (ECU)
17.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 7 JUNCTION CONNECTOR)
a.

Reconnect the wire harness connector to the CAN No. 6 junction connector.


b.

Disconnect the wire harness connector from the CAN No. 7 junction connector.


c.
C183982C14
1.781,2.063 2.198,2.302 0.417,0.24 0.948,0.844 0.646,0.844 0.646,0.844 0.646,2.177 false 1.24,1.177 0.938,1.177 0.938,1.177 0.938,2.167 false 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 1,0.75 1.573,0.906 0.573,0.156 10 false CANH*b 1.292,1.094 1.854,1.25 0.563,0.156 10 false CANL*b 1.844,2.094 2.115,2.26 0.271,0.167 10 false T18
*a Rear view of wire harness connector
(to CAN No. 7 Junction Connector)
*b to CAN No. 6 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T18-3 (CANH) - T18-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 6 JUNCTION CONNECTOR - CAN NO. 7 JUNCTION CONNECTOR)

18.CHECK FOR SHORT IN SUB BUS 2 LINES (ECU)
a.

Reconnect all wire harness connectors (CAN No. 5 junction connector, CAN No. 6 junction connector, CAN No. 7 junction connector and CAN No. 9 junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short-circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C238893C07
1.479,0.677 1.958,0.969 0.479,0.292 1.646,1.667 1.927,2.219 1.927,2.219 2.188,2.219 false 1.552,1.667 1.271,2.229 1.271,2.229 1.01,2.229 false 0.146,0.01 0.344,0.188 0.198,0.177 10 false *a 0.542,2.156 0.979,2.375 0.438,0.219 10 false CA2H 2.229,2.135 2.656,2.333 0.427,0.198 10 false CA2L 1.552,0.74 1.865,0.958 0.313,0.219 10 false I160
*a Component with harness connected
(Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).

·

If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), repair or replace the short-circuited branch line or connector.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU

NG

REPAIR OR REPLACE CORRESPONDING ECU BRANCH LINES OR CONNECTOR

19.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the I178 and I179 wire harness connectors.


b.

Measure the resistance according to the value(s) in the table below.

C310107C01
5.104,0.281 5.552,0.542 0.448,0.26 0.99,1.063 1.406,1.25 0.417,0.188 2.469,1.292 2.885,1.479 0.417,0.188 5.531,2.104 5.813,2.104 5.813,2.104 5.948,1.688 true 5.24,1.125 4.979,0.469 4.979,0.469 4.781,0.469 true 1.323,1.646 0.969,1.292 0.969,1.292 0.802,1.292 true 0.813,1.75 1.125,1.75 true 1.323,2.271 1.208,1.823 true 1.604,2.021 1.323,1.781 true 2.063,1.75 1.844,1.563 true 2.271,2.281 2.156,1.833 true 2.271,1.646 2.594,1.646 true 2.823,2.073 2.573,2.073 2.573,2.073 2.271,1.781 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 4.042,0.625 4.354,0.823 0.313,0.198 10 false *1 1.073,1.073 1.688,1.271 0.615,0.198 10 false I178 2.542,1.313 3.156,1.51 0.615,0.198 10 false I179 0.25,1.208 1.167,1.406 0.917,0.198 10 false CANH*b 1.427,2.042 2.344,2.24 0.917,0.198 10 false CANL*b 2.635,1.563 3.552,1.76 0.917,0.198 10 false CANH*c 2.875,1.99 3.792,2.188 0.917,0.198 10 false CANL*c 5.24,0.333 5.698,0.531 0.458,0.198 10 false I39 4.542,0.396 4.854,0.594 0.313,0.198 10 false CG 5.229,2.031 5.688,2.229 0.458,0.198 10 false BAT 0.667,1.677 0.823,1.875 0.156,0.198 10 false B 2.208,2.281 2.521,2.479 0.313,0.198 10 false LG 1.708,1.469 1.865,1.667 0.156,0.198 10 false V 1.26,2.281 1.573,2.479 0.313,0.198 10 false LG
*1 DLC3 - -
*a Rear view of wire harness connector
(to CAN No. 9 Junction Connector)
*b to Network Gateway ECU
*c to CAN No. 5 Junction Connector *d


Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
I178-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Network gateway ECU
I178-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
I179-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 5 junction connector
I179-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
I178-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short Network gateway ECU
I178-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
I179-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 5 junction connector
I179-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result Proceed to
OK A
NG (to network gateway ECU main bus line) B
NG (to CAN No. 5 junction connector main bus line) C


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




A

REPLACE CAN NO. 9 JUNCTION CONNECTOR

B

20.CHECK FOR SHORT IN SUB BUS 2 LINE (NETWORK GATEWAY ECU)

C

21.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 5 JUNCTION CONNECTOR)
20.CHECK FOR SHORT IN SUB BUS 2 LINE (NETWORK GATEWAY ECU)
a.

Disconnect the network gateway ECU connector.


b.
C238892C40
1.154,1.804 1.543,1.961 0.389,0.156 10 CA2L 2.211,1.804 2.6,1.961 0.389,0.156 10 CA2H 0.075,0.037 0.379,0.234 0.303,0.198 10 *a 2.571,0.889 2.945,1.07 0.374,0.181 10 GND 0.333,0.561 0.734,0.738 0.401,0.177 10 BATT 0.528,1.171 0.841,1.361 0.313,0.19 10 I160 0.478,1.139 0.899,1.377 0.421,0.238 1.966,1.501 1.966,1.885 1.966,1.885 2.193,1.885 false 1.842,1.501 1.842,1.885 1.842,1.885 1.615,1.885 false 2.202,1.262 2.43,0.977 2.43,0.977 2.545,0.977 false 1.242,1.262 0.96,0.648 0.96,0.648 0.79,0.648 false
*a Front view of wire harness connector
(to Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I160-13 (CA2H) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short
I160-12 (CA2L) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
I160-13 (CA2H) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short
I160-12 (CA2L) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result
OK
NG


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 9 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

21.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 5 JUNCTION CONNECTOR)
a.

Disconnect the wire harness connector from the CAN No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C240196C24
2.052,3.771 2.417,3.979 0.365,0.208 2.542,1.469 2.906,1.677 0.365,0.208 3.438,3.615 3.146,3.083 3.146,3.083 2.938,3.083 false 4.208,4.208 4.406,4.458 4.406,4.458 4.698,4.458 false 4.021,1.698 4.271,1.552 4.271,1.552 4.427,1.552 true 4.01,1.844 4.271,1.948 4.271,1.948 4.427,1.948 true 3.708,1.688 3.958,1.083 3.958,1.083 4.396,1.083 true 3.708,1.854 3.99,2.25 3.99,2.25 4.396,2.25 true 2.24,0.604 2.531,0.896 0.292,0.292 10 false *a 2.24,2.854 2.531,3.146 0.292,0.292 10 false *1 4.448,1 5.156,1.24 0.708,0.24 10 false CANH*b 4.49,1.479 5.198,1.719 0.708,0.24 10 false CANH*c 4.448,2.177 5.156,2.417 0.708,0.24 10 false CANL*b 4.469,1.875 5.177,2.115 0.708,0.24 10 false CANL*c 2.604,1.479 2.927,1.698 0.323,0.219 10 false O31 2.146,3.781 2.5,4 0.354,0.219 10 false I39 2.698,3 2.99,3.219 0.292,0.219 10 false CG 4.781,4.385 5.156,4.594 0.375,0.208 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 6 Junction Connector
*c to CAN No. 9 Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
O31-8 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 6 junction connector
O31-19 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
O31-11 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 9 junction connector
O31-22 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
O31-8 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 6 junction connector
O31-19 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
O31-11 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 9 junction connector
O31-22 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result Proceed to
OK A
NG (to CAN No. 9 junction connector main bus line) B
NG (to CAN No. 6 junction connector main bus line) C


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 9 JUNCTION CONNECTOR)

C

22.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 6 JUNCTION CONNECTOR)
22.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the wire harness connector from the CAN No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C240196C25
2.052,3.771 2.417,3.979 0.365,0.208 3.333,0.531 3.698,0.74 0.365,0.208 3.438,3.604 3.146,3.073 3.146,3.073 2.927,3.073 true 4.219,4.208 4.427,4.458 4.427,4.458 4.708,4.458 true 3.031,1.719 2.74,1.583 2.74,1.583 2.51,1.583 true 3.031,1.833 2.75,1.958 2.75,1.958 2.5,1.958 true 3.24,1.854 3.698,2.292 3.698,2.292 3.917,2.292 true 3.229,1.698 3.688,1.188 3.688,1.188 4.146,1.188 true 3.135,1.698 2.698,1.292 2.698,1.292 2.531,1.292 true 3.135,1.854 2.74,2.281 2.74,2.281 2.563,2.281 true 2.24,0.604 2.531,0.896 0.292,0.292 10 false *a 2.24,2.854 2.531,3.146 0.292,0.292 10 false *1 1.958,1.51 2.667,1.75 0.708,0.24 10 false CANH*b 1.99,1.208 2.698,1.448 0.708,0.24 10 false CANH*c 4.198,1.115 4.906,1.354 0.708,0.24 10 false CANH*d 1.979,1.875 2.688,2.115 0.708,0.24 10 false CANL*b 2.052,2.208 2.76,2.448 0.708,0.24 10 false CANL*c 3.969,2.219 4.677,2.458 0.708,0.24 10 false CANL*d 3.396,0.552 3.719,0.771 0.323,0.219 10 false T17 2.146,3.781 2.5,4 0.354,0.219 10 false I39 2.708,3.01 3,3.229 0.292,0.219 10 false CG 4.781,4.385 5.156,4.594 0.375,0.208 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 7 Junction Connector
*c to Rear Television Camera Assembly *d to CAN No. 5 Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
T17-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 7 junction connector
T17-12 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
T17-2 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Rear television camera assembly
T17-13 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
T17-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 5 junction connector
T17-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
T17-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 7 junction connector
T17-12 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
T17-2 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short Rear television camera assembly
T17-13 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
T17-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 5 junction connector
T17-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result Proceed to
OK A
NG (to CAN No. 5 junction connector main bus line) B
NG (to CAN No. 7 junction connector main bus line) C
NG (to rear television camera assembly) D


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

23.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 7 JUNCTION CONNECTOR)

D

24.CHECK FOR SHORT IN SUB BUS 2 LINE (ECU)
23.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 7 JUNCTION CONNECTOR)
a.

Disconnect the wire harness connector from the CAN No. 7 junction connector.


b.
C274535C02
1.51,0.302 1.948,0.646 0.438,0.344 1.563,2.146 2,2.49 0.438,0.344 2.104,1.302 2.104,1.875 2.104,1.875 2.385,1.875 false 1.823,1.302 1.823,1.875 1.823,1.875 1.406,1.875 false 2.563,4.094 2.563,3.823 false 1.677,3.073 1.677,2.656 1.677,2.656 1.469,2.656 false 2.448,1.802 3.01,2.125 0.563,0.323 10 false CANH 1,1.802 1.625,2.135 0.625,0.333 10 false CANL 0.135,0.146 0.563,0.448 0.427,0.302 10 false *a 2.458,4.135 3.021,4.458 0.563,0.323 10 false BAT 1.177,2.573 1.708,2.896 0.531,0.323 10 false CG 1.604,0.396 2.063,0.708 0.458,0.313 10 false T18 1.688,2.24 2.146,2.552 0.458,0.313 10 false I39 0.188,2.479 0.615,2.781 0.427,0.302 10 false *1
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 7 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
T18-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short
T18-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
T18-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short
T18-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 6 JUNCTION CONNECTOR - CAN NO. 7 JUNCTION CONNECTOR)

24.CHECK FOR SHORT IN SUB BUS 2 LINE (ECU)
a.

Reconnect all wire harness connectors (CAN No. 5 junction connector, CAN No. 6 junction connector, CAN No. 7 junction connector and CAN No. 9 junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the bus line shorted to B+ or shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C238893C06
1.51,0.677 1.99,0.969 0.479,0.292 1.656,1.667 1.938,2.135 1.938,2.135 2.198,2.135 false 1.552,1.677 1.292,2.146 1.292,2.146 1.031,2.146 false 2.042,1.51 2.406,0.813 2.406,0.813 2.646,0.813 false 1.385,1.51 1.042,0.823 1.042,0.823 0.802,0.823 false 0.063,0.031 0.26,0.208 0.198,0.177 10 false *a 0.656,2.063 1.448,2.271 0.792,0.208 10 false CA2H 2.229,2.052 2.885,2.25 0.656,0.198 10 false CA2L 2.698,0.74 3.375,0.927 0.677,0.188 10 false BATT 0.49,0.76 1.198,0.979 0.708,0.219 10 false GND 1.604,0.74 1.958,0.938 0.354,0.198 10 false I160
*a Component with harness connected
(Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I160-13 (CA2H) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short
I160-12 (CA2L) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
I160-13 (CA2H) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short
I160-12 (CA2L) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result
OK
NG


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.

·

If the resistance becomes abnormal when an ECU connector is reconnected, there may be a short in the ECU.




OK

REPLACE CORRESPONDING ECU

NG

REPAIR OR REPLACE CORRESPONDING ECU BRANCH LINES OR CONNECTOR

25.CHECK SUB BUS 2
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C238893C06
1.51,0.677 1.99,0.969 0.479,0.292 1.656,1.667 1.938,2.135 1.938,2.135 2.198,2.135 false 1.552,1.677 1.292,2.146 1.292,2.146 1.031,2.146 false 2.042,1.51 2.406,0.813 2.406,0.813 2.646,0.813 false 1.385,1.51 1.042,0.823 1.042,0.823 0.802,0.823 false 0.063,0.031 0.26,0.208 0.198,0.177 10 false *a 0.656,2.063 1.448,2.271 0.792,0.208 10 false CA2H 2.229,2.052 2.885,2.25 0.656,0.198 10 false CA2L 2.698,0.74 3.375,0.927 0.677,0.188 10 false BATT 0.49,0.76 1.198,0.979 0.708,0.219 10 false GND 1.604,0.74 1.958,0.938 0.354,0.198 10 false I160
*a Component with harness connected
(Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in main bus lines
I160-13 (CA2H) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I160-12 (CA2L) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I160-13 (CA2H) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I160-12 (CA2L) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus line B
Short circuit between bus lines C
·

Ground short

·

+B short


D



A

26.CHECK FOR DTC OUTPUT

B

27.CHECK FOR OPEN IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)

C

33.CHECK FOR SHORT IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)

D

40.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 9 JUNCTION CONNECTOR)
26.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Gateway > Clear DTCs
50002 150

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON and recheck for DTCs.

Body Electrical > Gateway > Trouble Codes
50001 150

Result:
Result Proceed to
U1002 is output from network gateway ECU
(GTS display: Gateway)
A
Other DTC is output B



A

B

27.CHECK FOR OPEN IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)
a.
C238892C39
0.479,1.146 0.865,1.365 0.385,0.219 1.844,1.51 1.844,1.792 1.844,1.792 1.667,1.792 false 1.958,1.51 1.958,1.802 1.958,1.802 2.156,1.802 false 0.115,0 0.365,0.24 0.25,0.24 10 false *a 2.188,1.74 2.896,1.938 0.708,0.198 10 false CA2H 1.313,1.74 2.021,1.917 0.708,0.177 10 false CA2L 0.542,1.167 0.823,1.365 0.281,0.198 10 false I160
*a Front view of wire harness connector
(to Network Gateway ECU)


Disconnect the network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

28.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 9 JUNCTION CONNECTOR)
28.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 9 JUNCTION CONNECTOR)
a.

Reconnect the network gateway ECU connector.


b.

Disconnect the I179 and I193 wire harness connectors.


c.
C325243C04
0.448,1.667 0.896,1.896 0.448,0.229 2.292,1.635 2.74,1.865 0.448,0.229 0.813,2.208 1.104,2.208 true 2.531,2.208 2.719,2.208 true 0.781,2.365 0.979,2.563 0.979,2.563 1.115,2.563 true 2.49,2.375 2.656,2.583 2.656,2.583 2.719,2.583 true 2.385,2.427 2.583,2.906 2.583,2.906 2.719,2.906 true 0.656,2.427 0.875,2.823 0.875,2.823 1.01,2.823 true 0.375,2.083 0.51,2.083 0.51,2.083 0.563,2.302 true 2.083,2.094 2.219,2.094 2.219,2.094 2.271,2.313 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.542,1.688 0.854,1.885 0.313,0.198 10 false I179 2.365,1.667 2.677,1.865 0.313,0.198 10 false I193 0.208,2.01 0.521,2.208 0.313,0.198 10 false V 1.094,2.75 1.406,2.948 0.313,0.198 10 false LG 2.802,2.833 3.115,3.031 0.313,0.198 10 false LG 1.177,2.125 2.021,2.354 0.844,0.229 10 false CANH*b 1.188,2.479 2.031,2.781 0.844,0.302 10 false CANL*b 2.75,2.135 3.396,2.406 0.646,0.271 10 false CANH*c 2.75,2.5 3.385,2.74 0.635,0.24 10 false CANL*c 1.938,2.021 2.25,2.219 0.313,0.198 10 false R
*a Rear view of wire harness connector
(to CAN No. 9 Junction Connector)
*b to CAN No. 5 Junction Connector
*c to CAN No. 8 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
I179-1 (CANH) - I179-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 5 junction connector
I193-1 (CANH) - I193-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 8 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 8 junction connector main bus line) B
NG (to CAN No. 5 junction connector main bus line) C



A

REPLACE CAN NO. 9 JUNCTION CONNECTOR

B

29.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 8 JUNCTION CONNECTOR)

C

30.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 5 JUNCTION CONNECTOR)
29.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 8 JUNCTION CONNECTOR)
a.

Reconnect the I179 and I193 wire harness connectors.


b.

Disconnect the wire harness connector from the CAN No. 8 junction connector.


c.
C234634C54
2.583,1.719 2.958,2.01 0.375,0.292 1.167,0.823 1.406,0.823 1.406,0.823 1.406,1.74 false 1.177,2.75 1.417,2.75 1.417,2.75 1.417,2.094 false 1.885,2.76 1.604,2.76 1.604,2.76 1.604,2.115 false 1.865,0.833 1.604,0.833 1.604,0.833 1.604,1.729 false 0.094,0.083 0.406,0.313 0.313,0.229 10 false *a 1,0.781 1.229,0.948 0.229,0.167 10 false *b 2.302,0.76 2.615,0.917 0.313,0.156 10 false *c 0.604,0.781 1.021,0.99 0.417,0.208 10 false CANH 0.667,2.698 1.281,2.896 0.615,0.198 10 false CANL 1.906,0.771 2.354,0.938 0.448,0.167 10 false CANH 1.927,2.698 2.344,2.875 0.417,0.177 10 false CANL 2.646,1.802 3.115,2.083 0.469,0.281 10 false S15 1.021,2.698 1.25,2.865 0.229,0.167 10 false *b 2.281,2.688 2.594,2.844 0.313,0.156 10 false *c
*a Front view of wire harness connector
(to CAN No. 8 Junction Connector)
*b to CAN No. 9 Junction Connector
*c to Network Gateway ECU


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
S15-2 (CANH) - S15-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 9 junction connector
S15-3 (CANH) - S15-9 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Network gateway ECU



Result:
Result Proceed to
OK A
NG (to network gateway ECU main bus line) B
NG (to CAN No. 9 junction connector main bus line) C



A

REPLACE CAN NO. 8 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 8 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 8 JUNCTION CONNECTOR - CAN NO. 9 JUNCTION CONNECTOR)

30.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 5 JUNCTION CONNECTOR)
a.

Reconnect the I179 and I193 wire harness connectors.


b.

Disconnect the wire harness connector from the CAN No. 5 junction connector.


c.
C238890C88
0.469,1.24 0.958,1.5 0.49,0.26 2.5,0.51 1.969,0.51 1.969,0.51 1.969,1.354 false 2.646,0.771 2.323,0.771 2.323,0.771 2.323,1.354 false 2.646,1.885 2.323,1.885 2.323,1.885 2.323,1.573 false 1.802,2.031 1.969,2.031 1.969,2.031 1.969,1.573 false 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.573,0.427 3.125,0.583 0.552,0.156 10 false CANH*b 2.677,0.688 3.229,0.844 0.552,0.156 10 false CANH*c 1.281,1.948 1.833,2.104 0.552,0.156 10 false CANL*b 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*c 0.552,1.281 0.833,1.479 0.281,0.198 10 false O31
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 6 Junction Connector
*c to CAN No. 9 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
O31-8 (CANH) - O31-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 6 junction connector
O31-11 (CANH) - O31-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 9 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 9 junction connector main bus line) B
NG (to CAN No. 6 junction connector main bus line) C



A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 9 JUNCTION CONNECTOR)

C

31.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 6 JUNCTION CONNECTOR)
31.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 6 JUNCTION CONNECTOR)
a.

Reconnect the wire harness connector to the CAN No. 5 junction connector.


b.

Disconnect the wire harness connector from the CAN No. 6 junction connector.


c.
C238890C89
1.021,0.281 1.5,0.531 0.479,0.25 0.75,1.219 0.927,1.219 0.927,1.219 1.135,1.406 true 0.688,0.708 0.917,0.708 0.917,0.708 1.385,1.365 true 1.719,1.885 1.396,1.885 1.396,1.885 1.396,1.573 true 0.698,1.656 0.958,1.656 0.958,1.656 1.167,1.563 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 0.208,1.135 0.76,1.292 0.552,0.156 10 false CANH*b 0.135,0.625 0.688,0.781 0.552,0.156 10 false CANH*c 0.167,1.583 0.719,1.74 0.552,0.156 10 false CANL*b 1.781,1.802 2.333,1.958 0.552,0.156 10 false CANL*c 1.125,0.323 1.406,0.531 0.281,0.208 10 false T17
*a Front view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 7 Junction Connector
*c to CAN No. 5 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
T17-1 (CANH) - T17-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 7 junction connector
T17-3 (CANH) - T17-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 5 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 5 junction connector main bus line) B
NG (to CAN No. 7 junction connector main bus line) C



A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

32.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 7 JUNCTION CONNECTOR)
32.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 7 JUNCTION CONNECTOR)
a.

Reconnect the wire harness connector to the CAN No. 6 junction connector.


b.

Disconnect the wire harness connector from the CAN No. 7 junction connector.


c.
C183982C14
1.781,2.063 2.198,2.302 0.417,0.24 0.948,0.844 0.646,0.844 0.646,0.844 0.646,2.177 false 1.24,1.177 0.938,1.177 0.938,1.177 0.938,2.167 false 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 1,0.75 1.573,0.906 0.573,0.156 10 false CANH*b 1.292,1.094 1.854,1.25 0.563,0.156 10 false CANL*b 1.844,2.094 2.115,2.26 0.271,0.167 10 false T18
*a Rear view of wire harness connector
(to CAN No. 7 Junction Connector)
*b to CAN No. 6 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T18-3 (CANH) - T18-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 6 JUNCTION CONNECTOR - CAN NO. 7 JUNCTION CONNECTOR)

33.CHECK FOR SHORT IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)
a.
C238892C39
0.479,1.146 0.865,1.365 0.385,0.219 1.844,1.51 1.844,1.792 1.844,1.792 1.667,1.792 false 1.958,1.51 1.958,1.802 1.958,1.802 2.156,1.802 false 0.115,0 0.365,0.24 0.25,0.24 10 false *a 2.188,1.74 2.896,1.938 0.708,0.198 10 false CA2H 1.313,1.74 2.021,1.917 0.708,0.177 10 false CA2L 0.542,1.167 0.823,1.365 0.281,0.198 10 false I160
*a Front view of wire harness connector
(to Network Gateway ECU)


Disconnect the network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

34.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 9 JUNCTION CONNECTOR)
34.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 9 JUNCTION CONNECTOR)
a.

Reconnect the network gateway ECU connector.


b.

Disconnect the I179, I192 and I193 wire harness connectors.


c.

Measure the resistance according to the value(s) in the table below.

C325244C03
2.188,1.25 2.594,1.49 0.406,0.24 3.635,1.313 4.042,1.552 0.406,0.24 4.75,1.302 5.156,1.542 0.406,0.24 2.406,1.781 2.635,1.781 true 3.802,1.802 4.031,1.802 true 4.958,1.802 5.188,1.802 true 1.938,1.646 2.063,1.646 2.063,1.646 2.188,1.875 true 3.354,1.521 3.479,1.521 3.479,1.521 3.604,1.875 true 4.448,1.552 4.573,1.552 4.573,1.552 4.76,1.875 true 4.958,1.938 5.094,2.167 5.094,2.167 5.208,2.167 true 3.792,1.938 3.927,2.167 3.927,2.167 4.042,2.167 true 2.396,1.927 2.531,2.156 2.531,2.156 2.646,2.156 true 2.292,1.958 2.49,2.438 2.49,2.438 2.604,2.438 true 3.677,1.979 3.875,2.458 3.875,2.458 3.99,2.458 true 4.833,1.979 5.031,2.458 5.031,2.458 5.146,2.458 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 2.26,1.292 2.573,1.49 0.313,0.198 10 false I179 3.708,1.354 4.021,1.552 0.313,0.198 10 false I192 4.833,1.354 5.146,1.552 0.313,0.198 10 false I193 1.771,1.583 1.958,1.813 0.188,0.229 10 false V 3.229,1.448 3.417,1.677 0.188,0.229 10 false L 2.688,1.708 3.708,2 1.021,0.292 10 false CANH*b 4.073,1.719 4.677,1.99 0.604,0.271 10 false CANH*c 5.271,1.719 6.177,2.021 0.906,0.302 10 false CANH*d 2.729,2.073 3.75,2.49 1.021,0.417 10 false CANL*b 4.104,2.073 4.708,2.344 0.604,0.271 10 false CANL*c 5.292,2.083 6.25,2.417 0.958,0.333 10 false CANL*d 2.677,2.365 3.281,2.635 0.604,0.271 10 false LG 4.073,2.385 4.677,2.656 0.604,0.271 10 false LG 5.25,2.396 5.854,2.667 0.604,0.271 10 false LG 4.302,1.479 4.604,1.708 0.302,0.229 10 false R
*a Rear view of wire harness connector
(to CAN No. 9 Junction Connector)
*b to CAN No. 5 Junction Connector
*c to Driving Support ECU Assembly *d to CAN No. 8 Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
I179-1 (CANH) - I179-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 5 junction connector
I192-1 (CANH) - I192-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Driving support ECU assembly
I193-1 (CANH) - I193-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 8 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 8 junction connector main bus line) B
NG (to CAN No. 5 junction connector main bus line) C
NG (to driving support ECU assembly) D



A

REPLACE CAN NO. 9 JUNCTION CONNECTOR

B

35.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 8 JUNCTION CONNECTOR)

C

36.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 5 JUNCTION CONNECTOR)

D

39.CHECK FOR SHORT IN SUB BUS 2 LINES (ECU)
35.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 8 JUNCTION CONNECTOR)
a.

Reconnect the I179 and I193 wire harness connectors.


b.

Disconnect the wire harness connector from the CAN No. 8 junction connector.


c.
C234634C55
2.583,1.719 2.958,2.01 0.375,0.292 1.167,0.823 1.406,0.823 1.406,0.823 1.406,1.74 true 1.177,2.75 1.417,2.75 1.417,2.75 1.417,2.094 true 1.885,2.76 1.604,2.76 1.604,2.76 1.604,2.115 true 1.865,0.833 1.604,0.833 1.604,0.833 1.604,1.729 true 0.719,1.542 0.885,1.542 0.885,1.542 1.219,1.802 true 0.75,2.219 0.906,2.219 0.906,2.219 1.219,2.031 true 0.094,0.083 0.406,0.313 0.313,0.229 10 false *a 1,0.781 1.229,0.948 0.229,0.167 10 false *c 2.302,0.76 2.615,0.917 0.313,0.156 10 false *d 0.604,0.781 1.021,0.99 0.417,0.208 10 false CANH 0.667,2.698 1.281,2.896 0.615,0.198 10 false CANL 1.906,0.771 2.354,0.938 0.448,0.167 10 false CANH 1.927,2.698 2.344,2.875 0.417,0.177 10 false CANL 2.646,1.802 3.115,2.083 0.469,0.281 10 false S15 1.021,2.698 1.25,2.865 0.229,0.167 10 false *c 2.281,2.688 2.594,2.844 0.313,0.156 10 false *d 0.156,1.448 1.073,1.646 0.917,0.198 10 false CANH*b 0.198,2.135 1.115,2.333 0.917,0.198 10 false CANH*b
*a Front view of wire harness connector
(to CAN No. 8 Junction Connector)
*b to Lane Departure Warning Camera
*c to CAN No. 9 Junction Connector
*d to Network Gateway ECU


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
S15-1 (CANH) - S15-7 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Lane departure warning camera
S15-2 (CANH) - S15-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 9 junction connector
S15-3 (CANH) - S15-9 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Network gateway ECU



Result:
Result Proceed to
OK A
NG (to network gateway ECU main bus line) B
NG (to CAN No. 9 junction connector main bus line) C
NG (to lane departure warning camera) D



A

REPLACE CAN NO. 8 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 8 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 8 JUNCTION CONNECTOR - CAN NO. 9 JUNCTION CONNECTOR)

D

39.CHECK FOR SHORT IN SUB BUS 2 LINES (ECU)
36.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 5 JUNCTION CONNECTOR)
a.

Reconnect the I179 and I193 wire harness connectors.


b.

Disconnect the wire harness connector from the CAN No. 5 junction connector.


c.
C238890C90
0.542,1.177 0.948,1.417 0.406,0.24 2.396,0.51 2.073,0.51 2.073,0.51 2.073,1.354 true 2.646,0.771 2.323,0.771 2.323,0.771 2.323,1.354 true 2.646,1.885 2.323,1.885 2.323,1.885 2.323,1.573 true 1.927,2.063 2.083,2.063 2.083,2.063 2.083,1.573 true 1.958,1.354 1.958,0.479 1.958,0.479 1.302,0.479 true 1.969,1.573 1.969,1.865 1.969,1.865 1.188,1.865 true 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 0.75,0.396 1.302,0.552 0.552,0.156 10 false CANH*b 2.563,0.427 3.115,0.583 0.552,0.156 10 false CANH*c 0.635,1.781 1.188,1.938 0.552,0.156 10 false CANL*b 1.375,1.958 1.927,2.115 0.552,0.156 10 false CANL*c 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*d 2.677,0.688 3.229,0.844 0.552,0.156 10 false CANH*d 0.583,1.208 0.896,1.417 0.313,0.208 10 false O31
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 6 Junction Connector
*c to Blind Spot Monitor Sensor RH
*d to CAN No. 9 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
O31-8 (CANH) - O31-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 6 junction connector
O31-9 (CANH) - O31-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Blind spot monitor sensor RH
O31-11 (CANH) - O31-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 9 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 9 junction connector main bus line) B
NG (to CAN No. 6 junction connector main bus line) C
NG (to blind spot monitor sensor RH) D



A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 9 JUNCTION CONNECTOR)

C

37.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 6 JUNCTION CONNECTOR)

D

39.CHECK FOR SHORT IN SUB BUS 2 LINES (ECU)
37.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 6 JUNCTION CONNECTOR)
a.

Reconnect the wire harness connector to the CAN No. 5 junction connector.


b.

Disconnect the wire harness connector from the CAN No. 6 junction connector.


c.
C238890C91
1.531,0.094 2.01,0.354 0.479,0.26 0.813,0.646 0.979,0.646 0.979,0.646 1.396,1.365 true 1.781,2.063 1.385,2.063 1.385,2.063 1.385,1.573 true 1.281,1.385 1,0.938 1,0.938 0.771,0.938 true 1.281,1.573 1.281,1.979 1.281,1.979 1.021,1.979 true 0.677,1.24 0.854,1.24 0.854,1.24 1.135,1.385 true 0.698,1.677 0.979,1.677 0.979,1.677 1.167,1.573 true 0.052,0.042 0.292,0.25 0.24,0.208 10 false *a 0.135,1.156 0.688,1.313 0.552,0.156 10 false CANH*b 0.229,0.854 0.781,1.01 0.552,0.156 10 false CANH*c 0.146,1.604 0.698,1.76 0.552,0.156 10 false CANL*b 0.51,1.906 1.063,2.063 0.552,0.156 10 false CANL*c 1.823,1.979 2.375,2.135 0.552,0.156 10 false CANL*d 0.271,0.563 0.823,0.719 0.552,0.156 10 false CANH*d 1.625,0.156 1.896,0.375 0.271,0.219 10 false T17
*a Front view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 7 Junction Connector
*c to Rear Television Camera Assembly
*d to CAN No. 5 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
T17-1 (CANH) - T17-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 7 junction connector
T17-2 (CANH) - T17-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Rear television camera assembly
T17-3 (CANH) - T17-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 5 junction connector



Result:
Result Proceed to
OK A
NG (to CAN No. 5 junction connector main bus line) B
NG (to CAN No. 7 junction connector main bus line) C
NG (to rear television camera assembly) D



A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

38.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 7 JUNCTION CONNECTOR)

D

39.CHECK FOR SHORT IN SUB BUS 2 LINES (ECU)
38.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 7 JUNCTION CONNECTOR)
a.

Reconnect the wire harness connector to the CAN No. 6 junction connector.


b.

Disconnect the wire harness connector from the CAN No. 7 junction connector.


c.
C183982C14
1.781,2.063 2.198,2.302 0.417,0.24 0.948,0.844 0.646,0.844 0.646,0.844 0.646,2.177 false 1.24,1.177 0.938,1.177 0.938,1.177 0.938,2.167 false 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 1,0.75 1.573,0.906 0.573,0.156 10 false CANH*b 1.292,1.094 1.854,1.25 0.563,0.156 10 false CANL*b 1.844,2.094 2.115,2.26 0.271,0.167 10 false T18
*a Rear view of wire harness connector
(to CAN No. 7 Junction Connector)
*b to CAN No. 6 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T18-3 (CANH) - T18-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 6 JUNCTION CONNECTOR - CAN NO. 7 JUNCTION CONNECTOR)

39.CHECK FOR SHORT IN SUB BUS 2 LINES (ECU)
a.

Reconnect all wire harness connectors (CAN No. 5 junction connector, CAN No. 6 junction connector, CAN No. 7 junction connector, CAN No. 8 junction connector and CAN No. 9 junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short-circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C238893C07
1.479,0.677 1.958,0.969 0.479,0.292 1.646,1.667 1.927,2.219 1.927,2.219 2.188,2.219 false 1.552,1.667 1.271,2.229 1.271,2.229 1.01,2.229 false 0.146,0.01 0.344,0.188 0.198,0.177 10 false *a 0.542,2.156 0.979,2.375 0.438,0.219 10 false CA2H 2.229,2.135 2.656,2.333 0.427,0.198 10 false CA2L 1.552,0.74 1.865,0.958 0.313,0.219 10 false I160
*a Component with harness connected
(Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).

·

If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), repair or replace the short-circuited branch line or connector.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU

NG

REPAIR OR REPLACE CORRESPONDING ECU BRANCH LINES OR CONNECTOR

40.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 9 JUNCTION CONNECTOR)
a.

Disconnect the I179, I192 and I193 wire harness connectors.


b.

Measure the resistance according to the value(s) in the table below.

C325245C03
5.479,0.25 5.792,0.458 0.313,0.208 3.313,1.24 3.698,1.438 0.385,0.198 2.344,1.24 2.698,1.458 0.354,0.219 0.885,1.229 1.26,1.438 0.375,0.208 5.198,0.521 5.396,0.521 5.396,0.521 5.615,1.063 true 6.135,2.146 6.333,2.146 6.333,2.146 6.333,1.615 true 2.458,1.708 2.635,1.708 true 1.073,1.698 1.25,1.698 true 3.51,1.719 3.688,1.719 true 1.073,1.844 1.167,2.094 1.167,2.094 1.281,2.094 true 2.438,1.854 2.531,2.104 2.531,2.104 2.646,2.104 true 3.5,1.865 3.594,2.115 3.594,2.115 3.708,2.115 true 0.979,1.875 1.115,2.365 1.115,2.365 1.229,2.365 true 2.333,1.885 2.469,2.375 2.469,2.375 2.583,2.375 true 3.396,1.896 3.531,2.385 3.531,2.385 3.646,2.385 true 3.063,1.479 3.208,1.479 3.208,1.479 3.323,1.792 true 2,1.469 2.146,1.469 2.146,1.469 2.26,1.781 true 0.635,1.458 0.781,1.458 0.781,1.458 0.896,1.771 true 0.875,0.198 1.188,0.396 0.313,0.198 10 false *a 4.208,0.365 4.521,0.563 0.313,0.198 10 false *1 4.938,0.438 5.24,0.677 0.302,0.24 10 false CG 5.552,0.271 5.854,0.51 0.302,0.24 10 false I39 5.771,2.073 6.073,2.313 0.302,0.24 10 false BAT 0.938,1.25 1.479,1.552 0.542,0.302 10 false I179 2.385,1.271 2.854,1.521 0.469,0.25 10 false I192 3.375,1.26 3.958,1.542 0.583,0.281 10 false I193 1.313,1.615 1.885,1.885 0.573,0.271 10 false CANH*b 2.677,1.625 3.25,1.896 0.573,0.271 10 false CANH*c 3.75,1.635 4.719,1.917 0.969,0.281 10 false CANH*d 1.344,2.01 1.917,2.281 0.573,0.271 10 false CANL*b 2.708,2.021 3.281,2.292 0.573,0.271 10 false CANL*c 3.792,2.031 4.865,2.417 1.073,0.385 10 false CANL*d 0.479,1.375 0.781,1.615 0.302,0.24 10 false V 1.854,1.396 2.156,1.635 0.302,0.24 10 false L 1.313,2.281 1.615,2.521 0.302,0.24 10 false LG 2.656,2.302 2.958,2.542 0.302,0.24 10 false LG 3.729,2.313 4.031,2.552 0.302,0.24 10 false LG 2.938,1.396 3.198,1.583 0.26,0.188 10 false R
*1 DLC3 - -
*a Rear view of wire harness connector
(to CAN No. 9 Junction Connector)
*b to CAN No. 5 Junction Connector
*c to Driving Support ECU Assembly *d to CAN No. 8 Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
I179-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 5 junction connector
I179-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
I192-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Driving support ECU assembly
I192-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
I193-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 8 junction connector
I193-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
I179-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 5 junction connector
I179-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
I192-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short Driving support ECU assembly
I192-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
I193-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 8 junction connector
I193-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result Proceed to
OK A
NG (to CAN No. 8 junction connector main bus line) B
NG (to CAN No. 5 junction connector main bus line) C
NG (to driving support ECU assembly) D


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




A

REPLACE CAN NO. 9 JUNCTION CONNECTOR

B

41.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 8 JUNCTION CONNECTOR)

C

43.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 5 JUNCTION CONNECTOR)

D

46.CHECK FOR SHORT IN SUB BUS 2 LINE (ECU)
41.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 8 JUNCTION CONNECTOR)
a.

Disconnect the wire harness connector from the CAN No. 8 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C266533C01
3.313,0.76 3.75,1.042 0.438,0.281 3.333,2.76 3.771,3.042 0.438,0.281 3.479,3.469 3.135,3.031 3.135,3.031 2.875,3.031 true 4.49,4.354 4.271,4.354 4.271,4.354 4.073,3.906 true 2.563,1.594 2.771,1.594 2.771,1.594 3.125,1.823 true 2.583,2.292 2.792,2.292 2.792,2.292 3.125,2 true 2.448,1.25 2.677,1.25 2.677,1.25 3.313,1.771 true 2.729,2.531 2.927,2.531 2.927,2.531 3.313,2.073 true 3.469,1.76 4.281,1.094 4.281,1.094 4.573,1.094 true 4.125,2.531 3.813,2.531 3.813,2.531 3.458,2.052 true 2.406,0.75 2.719,0.948 0.313,0.198 10 false *a 2.438,2.698 2.75,2.896 0.313,0.198 10 false *1 1.979,1.521 2.896,1.719 0.917,0.198 10 false CANH*b 2.052,2.219 2.969,2.417 0.917,0.198 10 false CANL*b 1.896,1.177 2.813,1.375 0.917,0.198 10 false CANH*c 2.208,2.448 3.125,2.646 0.917,0.198 10 false CANL*c 4.635,1.031 5.552,1.229 0.917,0.198 10 false CANH*d 4.198,2.469 5.115,2.667 0.917,0.198 10 false CANL*d 3.396,0.823 3.854,1.021 0.458,0.198 10 false S15 3.458,2.823 3.917,3.021 0.458,0.198 10 false I39 2.625,2.958 2.938,3.156 0.313,0.198 10 false CG 4.542,4.281 5,4.479 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 8 Junction Connector)
*b to Lane Departure Warning Camera
*c to CAN No. 9 Junction Connector *d to Network Gateway ECU


Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
S15-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Lane departure warning camera
S15-7 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
S15-2 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 9 junction connector
S15-8 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
S15-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Network gateway ECU
S15-9 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
S15-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short Lane departure warning camera
S15-7 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
S15-2 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 9 junction connector
S15-8 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
S15-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short Network gateway ECU
S15-9 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result Proceed to
OK A
NG (to network gateway ECU) B
NG (to CAN No. 9 junction connector main bus line) C
NG (to lane departure warning camera) D


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




A

REPLACE CAN NO. 8 JUNCTION CONNECTOR

B

42.CHECK FOR SHORT IN SUB BUS 2 LINE (NETWORK GATEWAY ECU)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 8 JUNCTION CONNECTOR - CAN NO. 9 JUNCTION CONNECTOR)

D

46.CHECK FOR SHORT IN SUB BUS 2 LINE (ECU)
42.CHECK FOR SHORT IN SUB BUS 2 LINE (NETWORK GATEWAY ECU)
a.

Disconnect the network gateway ECU connector.


b.
C238892C40
1.154,1.804 1.543,1.961 0.389,0.156 10 CA2L 2.211,1.804 2.6,1.961 0.389,0.156 10 CA2H 0.075,0.037 0.379,0.234 0.303,0.198 10 *a 2.571,0.889 2.945,1.07 0.374,0.181 10 GND 0.333,0.561 0.734,0.738 0.401,0.177 10 BATT 0.528,1.171 0.841,1.361 0.313,0.19 10 I160 0.478,1.139 0.899,1.377 0.421,0.238 1.966,1.501 1.966,1.885 1.966,1.885 2.193,1.885 false 1.842,1.501 1.842,1.885 1.842,1.885 1.615,1.885 false 2.202,1.262 2.43,0.977 2.43,0.977 2.545,0.977 false 1.242,1.262 0.96,0.648 0.96,0.648 0.79,0.648 false
*a Front view of wire harness connector
(to Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I160-13 (CA2H) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short
I160-12 (CA2L) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
I160-13 (CA2H) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short
I160-12 (CA2L) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result
OK
NG


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 8 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

43.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 5 JUNCTION CONNECTOR)
a.

Disconnect the wire harness connector from the CAN No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C240196C26
2.052,3.771 2.417,3.979 0.365,0.208 2.542,1.469 2.906,1.677 0.365,0.208 3.438,3.615 3.146,3.083 3.146,3.083 2.938,3.083 false 4.208,4.208 4.406,4.458 4.406,4.458 4.698,4.458 false 4.021,1.698 4.271,1.552 4.271,1.552 4.427,1.552 true 4.01,1.844 4.271,1.948 4.271,1.948 4.427,1.948 true 3.802,1.854 4.26,2.292 4.26,2.292 4.49,2.292 true 3.792,1.688 4.25,1.177 4.25,1.177 4.448,1.177 true 3.698,1.688 4.021,0.865 4.021,0.865 4.635,0.865 true 3.708,1.854 4.083,2.625 4.083,2.625 4.677,2.625 true 2.24,0.604 2.531,0.896 0.292,0.292 10 false *a 2.24,2.854 2.531,3.146 0.292,0.292 10 false *1 4.688,0.781 5.396,1.021 0.708,0.24 10 false CANH*b 4.531,1.094 5.24,1.333 0.708,0.24 10 false CANH*c 4.479,1.479 5.188,1.719 0.708,0.24 10 false CANH*d 4.75,2.552 5.458,2.792 0.708,0.24 10 false CANL*b 4.563,2.219 5.271,2.458 0.708,0.24 10 false CANL*c 4.479,1.875 5.188,2.115 0.708,0.24 10 false CANL*d 2.604,1.479 2.927,1.698 0.323,0.219 10 false O31 2.146,3.781 2.5,4 0.354,0.219 10 false I39 2.698,3 2.99,3.219 0.292,0.219 10 false CG 4.781,4.385 5.156,4.594 0.375,0.208 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 6 Junction Connector
*c to Blind Spot Monitor Sensor RH *d to CAN No. 9 Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
O31-8 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 6 junction connector
O31-19 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
O31-9 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Blind spot monitor sensor RH
O31-20 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
O31-11 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 9 junction connector
O31-22 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
O31-8 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 6 junction connector
O31-19 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
O31-9 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short Blind spot monitor sensor RH
O31-20 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
O31-11 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 9 junction connector
O31-22 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result Proceed to
OK A
NG (to CAN No. 9 junction connector main bus line) B
NG (to CAN No. 6 junction connector main bus line) C
NG (to blind spot monitor sensor RH) D


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 9 JUNCTION CONNECTOR)

C

44.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 6 JUNCTION CONNECTOR)

D

46.CHECK FOR SHORT IN SUB BUS 2 LINE (ECU)
44.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the wire harness connector from the CAN No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C240196C27
2.052,3.771 2.417,3.979 0.365,0.208 3.344,0.5 3.708,0.708 0.365,0.208 3.438,3.604 3.146,3.073 3.146,3.073 2.927,3.073 false 4.219,4.208 4.427,4.458 4.427,4.458 4.708,4.458 false 3.24,1.865 3.396,2.469 3.396,2.469 3.729,2.469 true 3.229,1.698 2.802,0.896 2.802,0.896 2.51,0.896 true 3.135,1.688 2.771,1.25 2.771,1.25 2.427,1.25 true 3.135,1.854 2.917,2.229 2.917,2.229 2.625,2.229 true 3.042,1.708 2.771,1.594 2.771,1.594 2.531,1.594 true 2.542,1.969 2.792,1.969 2.792,1.969 3.021,1.833 true 2.229,0.313 2.521,0.604 0.292,0.292 10 false *a 2.24,2.854 2.531,3.146 0.292,0.292 10 false *1 1.979,1.51 2.688,1.75 0.708,0.24 10 false CANH*b 1.896,1.167 2.604,1.406 0.708,0.24 10 false CANH*c 1.99,1.885 2.698,2.125 0.708,0.24 10 false CANL*b 2.104,2.135 2.813,2.375 0.708,0.24 10 false CANL*c 3.771,2.396 4.479,2.635 0.708,0.24 10 false CANL*d 3.406,0.521 3.729,0.74 0.323,0.219 10 false T17 2.146,3.781 2.5,4 0.354,0.219 10 false I39 2.708,3.01 3,3.229 0.292,0.219 10 false CG 4.781,4.385 5.156,4.594 0.375,0.208 10 false BAT 1.958,0.802 2.667,1.042 0.708,0.24 10 false CANH*d
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 7 Junction Connector
*c to Rear Television Camera Assembly *d to CAN No. 5 Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
T17-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 7 junction connector
T17-12 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
T17-2 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Rear television camera assembly
T17-13 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
T17-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 5 junction connector
T17-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
T17-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 7 junction connector
T17-12 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
T17-2 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short Rear television camera assembly
T17-13 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
T17-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 5 junction connector
T17-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result Proceed to
OK A
NG (to CAN No. 5 junction connector main bus line) B
NG (to CAN No. 7 junction connector main bus line) C
NG (to rear television camera assembly) D


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

45.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 7 JUNCTION CONNECTOR)

D

46.CHECK FOR SHORT IN SUB BUS 2 LINE (ECU)
45.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 7 JUNCTION CONNECTOR)
a.

Disconnect the wire harness connector from the CAN No. 7 junction connector.


b.
C274535C02
1.51,0.302 1.948,0.646 0.438,0.344 1.563,2.146 2,2.49 0.438,0.344 2.104,1.302 2.104,1.875 2.104,1.875 2.385,1.875 false 1.823,1.302 1.823,1.875 1.823,1.875 1.406,1.875 false 2.563,4.094 2.563,3.823 false 1.677,3.073 1.677,2.656 1.677,2.656 1.469,2.656 false 2.448,1.802 3.01,2.125 0.563,0.323 10 false CANH 1,1.802 1.625,2.135 0.625,0.333 10 false CANL 0.135,0.146 0.563,0.448 0.427,0.302 10 false *a 2.458,4.135 3.021,4.458 0.563,0.323 10 false BAT 1.177,2.573 1.708,2.896 0.531,0.323 10 false CG 1.604,0.396 2.063,0.708 0.458,0.313 10 false T18 1.688,2.24 2.146,2.552 0.458,0.313 10 false I39 0.188,2.479 0.615,2.781 0.427,0.302 10 false *1
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 7 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
T18-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short
T18-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
T18-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short
T18-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 6 JUNCTION CONNECTOR - CAN NO. 7 JUNCTION CONNECTOR)

46.CHECK FOR SHORT IN SUB BUS 2 LINE (ECU)
a.

Reconnect all wire harness connectors (CAN No. 5 junction connector, CAN No. 6 junction connector, CAN No. 7 junction connector, CAN No. 8 junction connector and CAN No. 9 junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the bus line shorted to B+ or shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C238893C06
1.51,0.677 1.99,0.969 0.479,0.292 1.656,1.667 1.938,2.135 1.938,2.135 2.198,2.135 false 1.552,1.677 1.292,2.146 1.292,2.146 1.031,2.146 false 2.042,1.51 2.406,0.813 2.406,0.813 2.646,0.813 false 1.385,1.51 1.042,0.823 1.042,0.823 0.802,0.823 false 0.063,0.031 0.26,0.208 0.198,0.177 10 false *a 0.656,2.063 1.448,2.271 0.792,0.208 10 false CA2H 2.229,2.052 2.885,2.25 0.656,0.198 10 false CA2L 2.698,0.74 3.375,0.927 0.677,0.188 10 false BATT 0.49,0.76 1.198,0.979 0.708,0.219 10 false GND 1.604,0.74 1.958,0.938 0.354,0.198 10 false I160
*a Component with harness connected
(Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I160-13 (CA2H) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short
I160-12 (CA2L) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
I160-13 (CA2H) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short
I160-12 (CA2L) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result
OK
NG


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.

·

If the resistance becomes abnormal when an ECU connector is reconnected, there may be a short in the ECU.




OK

REPLACE CORRESPONDING ECU

NG

REPAIR OR REPLACE CORRESPONDING ECU BRANCH LINES OR CONNECTOR