Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2015.04–2016.05
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0265  Lost Communication with Parking Assist Monitor Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0265 Lost Communication with Parking Assist Monitor Module No communication from the rear television camera assembly continues.
·

Rear television camera assembly branch line or connector

·

Power source circuit of rear television camera assembly

·

Rear television camera assembly ground circuit

·

Rear television camera assembly


Network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.

HINT:

This diagnosis procedure is for when DTC U0265 is output by the network gateway ECU (GTS display: Gateway).


WIRING DIAGRAM

C325231E01
1.833,0.979 1.552,0.542 1.552,0.542 1.323,0.542 true 6.844,0.979 6.583,0.115 6.583,0.115 6.354,0.115 true 5.802,0.99 5.604,0.438 5.604,0.438 5.375,0.438 true 3.917,0.979 3.719,0.365 3.719,0.365 3.49,0.365 true 1.958,3.229 2.167,3.229 2.167,3.229 2.771,2.469 true 0.031,0.042 1.813,0.333 1.781,0.292 12 false Sub Bus 2: 0.083,2.5 1.188,2.906 1.104,0.406 10 false Network Gateway ECU 0.042,0.448 1.281,0.979 1.24,0.531 10 false CAN No. 8 Junction Connector* 0.01,3.135 2.26,3.438 2.25,0.302 10 false CAN No. 9 Junction Connector 2.219,0.271 3.458,0.771 1.24,0.5 10 false CAN No. 5 Junction Connector 4.094,0.354 5.354,0.854 1.26,0.5 10 false CAN No. 6 Junction Connector 4.406,0.031 6.469,0.344 2.063,0.313 10 false CAN No. 7 Junction Connector 0.583,1.885 1.354,2.083 0.771,0.198 10 false 120 Ω 6.26,1.896 7.031,2.094 0.771,0.198 10 false 120 Ω 1.854,3.646 2.823,3.927 0.969,0.281 10 false Trouble Area 4.573,2.781 4.729,2.979 0.156,0.198 10 false 4 5.156,2.781 5.313,2.979 0.156,0.198 10 false 1 4.521,2.969 5.135,3.167 0.615,0.198 10 false CANH 5.031,2.969 5.646,3.167 0.615,0.198 10 false CANL 4.417,3.26 4.875,3.458 0.458,0.198 10 false CB+ 4.427,3.531 5.042,3.729 0.615,0.198 10 false CGND 4.25,3.135 4.406,3.333 0.156,0.198 10 false 6 4.25,3.635 4.406,3.833 0.156,0.198 10 false 5 3.26,3.208 4.083,3.771 0.823,0.563 10 false Navigation Receiver Assembly 0.156,4.052 2.229,4.385 2.073,0.333 10 false *: w/ Pre-crash Safety System 4.438,3.969 4.896,4.167 0.458,0.198 10 false T22 4.719,3.958 5.896,4.396 1.177,0.438 10 false Rear Television Camera Assembly 1.438,5.01 3.542,5.302 2.104,0.292 10 false : CAN Main Bus Line (CANH) 1.438,5.417 3.469,5.656 2.031,0.24 10 false : CAN Main Bus Line (CANL) 4.396,5.01 6.313,5.25 1.917,0.24 10 false : CAN Branch Line (CANH) 4.406,5.427 6.271,5.677 1.865,0.25 10 false : CAN Branch Line (CANL)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 22 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

Body Electrical > Gateway > Trouble Codes
50001 150
HINT:

If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.



Result:
Result Proceed to
U1002 is not output from network gateway ECU (GTS display: Gateway) A
U1002 is output from network gateway ECU (GTS display: Gateway) B



A

2.CHECK FOR OPEN IN SUB BUS 2 LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 2 LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the rear television camera assembly connector.


c.
C294680C31
1.573,0.188 1.958,0.479 0.385,0.292 0.979,1.958 1.146,1.958 1.146,1.958 1.563,1.417 true 0.99,0.563 1.135,0.563 1.135,0.563 1.552,1.156 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.646,0.229 2.104,0.427 0.458,0.198 10 false T22 0.583,0.469 1.198,0.667 0.615,0.198 10 false CANL 0.563,1.865 1.177,2.063 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T22-4 (CANH) - T22-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C294680C32
1.573,0.188 1.958,0.479 0.385,0.292 1.198,1.958 1.365,1.958 1.365,1.958 1.781,1.417 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.656,0.229 2.115,0.427 0.458,0.198 10 false T22 0.76,1.865 1.375,2.063 0.615,0.198 10 false CGND
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T22-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C294680C33
1.573,0.188 1.958,0.479 0.385,0.292 1.385,1.958 1.552,1.958 1.552,1.958 1.969,1.417 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false T22 1.052,1.865 1.667,2.063 0.615,0.198 10 false CB+
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T22-6 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V



Result:
Result
OK
NG



OK

REPLACE REAR TELEVISION CAMERA ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)