Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT › from 2016.05
RM19V0EQ _53 Suspension _014587 ALIGNMENT / HANDLING DIAGNOSIS _0074016 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


PROCEDURE

Hide 2.MEASURE VEHICLE HEIGHT

C239047N07
1.49,1.24 1.688,1.448 0.198,0.208 10 false D 0.5,4.104 0.76,4.354 0.26,0.25 10 false A 2.063,4.177 2.333,4.396 0.271,0.219 10 false B 2.927,1.177 3.083,1.385 0.156,0.208 10 false C

NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Make sure to perform the wheel alignment with the vehicle unloaded and the fuel tank fully filled with fuel.

·

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Measure the vehicle height.

Measurement points:

A: Ground clearance of front wheel center


B: Ground clearance of lower No. 2 suspension arm bushing set bolt center


C: Ground clearance of rear wheel center


D: Ground clearance of strut rod set bolt center


Vehicle Height (Unloaded Vehicle):
Model Front A - B Rear C - D
ASV50R-DETDKQ 124.1 mm (4.89 in.)
115.4 mm (4.54 in.)*1
128.4 mm (5.06 in.)*4
48.9 mm (1.93 in.)
40.2 mm (1.58 in.)*1
56.3 mm (2.22 in.)*4
ASV50R-DETNKQ
ASV50R-DETVKQ 126.6 mm (4.98 in.)*3
128.4 mm (5.06 in.)*4
55.0 mm (2.17 in.)*3
56.3 mm (2.22 in.)*4
ASV50L-DETDKV 123.5 mm (4.86 in.)
113.5 mm (4.47 in.)*2
48.1 mm (1.89 in.)
38.1 mm (1.50 in.)*2
ASV50L-DETNKV


*1 for Papua New Guinea and Fiji

*2 for Iran and Yemen

*3 for 17 inch Wheel

*4 for 18 inch Wheel


Hide 3.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C17
2.406,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.469 false 2.771,0.75 2.958,0.917 0.188,0.167 10 false *2 0.427,0.635 0.615,0.792 0.188,0.156 10 false *1
*1 Turning Radius Gauge
*2 Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
Model Camber Inclination Right-left Difference
ASV50R-DETDKQ -0.69° +/- 0.75° (-0°41' +/- 45')
-0.59° +/- 0.75° (-0°35' +/- 45')*1
-0.72° +/- 0.75° (-0°43' +/- 45')*4
0.75° (0°45') or less
ASV50R-DETNKQ
ASV50R-DETVKQ -0.71° +/- 0.75° (-0°43' +/- 45')*3
-0.72° +/- 0.75° (-0°43' +/- 45')*4
ASV50L-DETDKV -0.68° +/- 0.75° (-0°41' +/- 45')
-0.57° +/- 0.75° (-0°34' +/- 45')*2
0.75° (0°45') or less
ASV50L-DETNKV


*1 for Papua New Guinea and Fiji

*2 for Iran and Yemen

*3 for 17 inch Wheel

*4 for 18 inch Wheel

Caster (Unloaded Vehicle):
Model Caster Inclination Right-left Difference
ASV50R-DETDKQ 2.81° +/- 0.75° (2°48' +/- 45')
2.73° +/- 0.75° (2°44' +/- 45')*1
2.95° +/- 0.75° (2°57' +/- 45')*4
0.75° (0°45') or less
ASV50R-DETNKQ
ASV50R-DETVKQ 2.94° +/- 0.75° (2°56' +/- 45')*3
2.95° +/- 0.75° (2°57' +/- 45')*4
ASV50L-DETDKV 2.80° +/- 0.75° (2°48' +/- 45')
2.71° +/- 0.75° (2°43' +/- 45')*2
0.75° (0°45') or less
ASV50L-DETNKV


*1 for Papua New Guinea and Fiji

*2 for Iran and Yemen

*3 for 17 inch Wheel

*4 for 18 inch Wheel

Steering Axis Inclination (Unloaded Vehicle):
Model Steering Axis Inclination
ASV50R-DETDKQ 12.10° (12°06')
11.91° (11°55')*1
12.19° (12°11')*4
ASV50R-DETNKQ
ASV50R-DETVKQ 12.15° (12°09')*3
12.19° (12°11')*4
ASV50L-DETDKV 12.09° (12°05')
11.86° (11°52')*2
ASV50L-DETNKV


*1 for Papua New Guinea and Fiji

*2 for Iran and Yemen

*3 for 17 inch Wheel

*4 for 18 inch Wheel


Hide 4.ADJUST CAMBER

NOTICE:

Inspect toe-in after the camber has been adjusted.


a.

Remove the front wheel.


b.
C247224

Remove the 2 nuts on the lower side of the front shock absorber assembly.

NOTICE:

Keep the bolts inserted.



c.

Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber assembly.

HINT:
·

Reinstall each bolt after removing it and confirming steering knuckle movement.

·

If the steering knuckle does not move freely in the front shock absorber assembly, clean the installation surfaces of the front shock absorber assembly and the steering knuckle.




d.

Temporarily install the 2 nuts. (Step A)


e.
C199624N05
1.01,0.125 1.167,0.323 0.156,0.198 10 - 1.875,0.052 2.031,0.25 0.156,0.198 10 +

Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)

Camber (Unloaded Vehicle):
Model Camber Inclination Right-left Difference
ASV50R-DETDKQ -0.69° +/- 0.75° (-0°41' +/- 45')
-0.59° +/- 0.75° (-0°35' +/- 45')*1
-0.72° +/- 0.75° (-0°43' +/- 45')*4
0.75° (0°45') or less
ASV50R-DETNKQ
ASV50R-DETVKQ -0.71° +/- 0.75° (-0°43' +/- 45')*3
-0.72° +/- 0.75° (-0°43' +/- 45')*4
ASV50L-DETDKV -0.68° +/- 0.75° (-0°41' +/- 45')
-0.57° +/- 0.75° (-0°34' +/- 45')*2
0.75° (0°45') or less
ASV50L-DETNKV


*1 for Papua New Guinea and Fiji

*2 for Iran and Yemen

*3 for 17 inch Wheel

*4 for 18 inch Wheel

HINT:

Perform adjustments so that the value is as close as possible to the median of the specified range.



f.
C247224

Tighten the nuts.

Torque:
290 N*m (2957 kgf*cm, 214 ft.*lbf)

NOTICE:

Keep the bolts from rotating when tightening the nuts.



g.

Install the front wheel.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)


h.
C247015N01
1.313,0.469 1.313,0.167 1.313,0.167 1.708,0.167 false 1.344,0.781 1.344,1.052 false 1.708,0.083 1.906,0.323 0.198,0.24 10 false 1 1.323,1.052 1.521,1.313 0.198,0.26 10 false 2

Check the camber.

If the measured value is not within the specification, calculate the required adjustment amount using the formula below.

Camber adjustment amount = center of the specified range - measured value

Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.

HINT:

Try to adjust the camber to the center of the specified values.


To move the axle hub toward (+) in step B To move the axle hub toward (-) in step B
Refer to table (1) (To move the axle hub toward the positive side) Refer to table (2) (To move the axle hub toward the negative side)

The vehicle body and suspension may be damaged if the camber cannot be correctly adjusted according to the tables above.

NOTICE:

Replace the nut with a new one when replacing the bolt.


i.

Table (1) (To move the axle hub toward the positive side)

C212217C08
2.052,0.531 2.188,0.74 0.135,0.208 10 false 1 2.052,1.146 2.188,1.354 0.135,0.208 10 false 2 2.521,0.792 2.75,0.99 0.229,0.198 10 false *c 3.219,1.406 3.448,1.594 0.229,0.188 10 false *d 5.979,0.792 6.198,0.99 0.219,0.198 10 false *e 5.271,0.792 5.521,0.99 0.25,0.198 10 false *d 4.604,1.406 4.781,1.583 0.177,0.177 10 false *f 3.917,1.406 4.125,1.615 0.208,0.208 10 false *e 4.396,6.375 4.583,6.552 0.188,0.177 10 false *f 5.969,1.396 6.177,1.552 0.208,0.156 10 false *f 5.271,1.406 5.469,1.583 0.198,0.177 10 false *f 6.656,1.396 6.833,1.552 0.177,0.156 10 false *f 6.646,0.792 6.854,0.969 0.208,0.177 10 false *f 2.542,2.99 2.719,3.219 0.177,0.229 10 false A 2.542,4.188 2.771,4.406 0.229,0.219 10 false F 2.542,3.469 2.771,3.688 0.229,0.219 10 false C 2.542,3.938 2.74,4.156 0.198,0.219 10 false E 2.542,3.24 2.729,3.448 0.188,0.208 10 false B 2.542,3.708 2.729,3.927 0.188,0.219 10 false D 3.927,3.01 4.177,3.24 0.25,0.229 10 false C 5.271,3 5.51,3.229 0.24,0.229 10 false E 3.229,3.01 3.406,3.219 0.177,0.208 10 false B 4.604,3 4.792,3.24 0.188,0.24 10 false D 3.229,2.76 3.448,2.99 0.219,0.229 10 false G 3.229,3.24 3.406,3.448 0.177,0.208 10 false C 3.229,3.708 3.448,3.938 0.219,0.229 10 false E 3.229,3.469 3.427,3.698 0.198,0.229 10 false D 3.229,3.938 3.427,4.167 0.198,0.229 10 false F 3.927,2.51 4.115,2.74 0.188,0.229 10 false G 3.927,2.76 4.135,2.969 0.208,0.208 10 false A 3.927,3.708 4.115,3.938 0.188,0.229 10 false F 3.917,3.469 4.083,3.688 0.167,0.219 10 false E 3.927,3.24 4.135,3.458 0.208,0.219 10 false D 4.604,2.281 4.802,2.531 0.198,0.25 10 false G 6.656,1.563 6.833,1.823 0.177,0.26 10 false G 5.979,1.813 6.26,2.063 0.281,0.25 10 false G 5.271,2.031 5.458,2.281 0.188,0.25 10 false G 6.656,1.813 6.813,2.042 0.156,0.229 10 false A 6.656,2.281 6.844,2.531 0.188,0.25 10 false C 6.656,2.76 6.885,3.01 0.229,0.25 10 false E 6.656,2.031 6.833,2.26 0.177,0.229 10 false B 6.656,2.51 6.875,2.781 0.219,0.271 10 false D 5.979,2.031 6.177,2.292 0.198,0.26 10 false A 5.979,2.51 6.188,2.75 0.208,0.24 10 false C 5.979,2.281 6.26,2.531 0.281,0.25 10 false B 5.979,2.76 6.167,2.99 0.188,0.229 10 false D 5.979,3 6.115,3.208 0.135,0.208 10 false F 5.271,3.24 5.49,3.448 0.219,0.208 10 false F 5.271,2.281 5.406,2.51 0.135,0.229 10 false A 5.271,2.76 5.448,2.969 0.177,0.208 10 false C 5.271,2.51 5.438,2.74 0.167,0.229 10 false B 4.604,2.51 4.781,2.76 0.177,0.25 10 false A 4.604,2.76 4.781,2.969 0.177,0.208 10 false B 4.604,3.24 4.813,3.458 0.208,0.219 10 false E 4.604,3.469 4.813,3.698 0.208,0.229 10 false F 1.625,5.073 1.76,5.281 0.135,0.208 10 false A 5.094,5.073 5.229,5.281 0.135,0.208 10 false F 3.052,5.073 3.188,5.281 0.135,0.208 10 false C 4.406,5.073 4.542,5.281 0.135,0.208 10 false E 2.344,5.073 2.479,5.281 0.135,0.208 10 false B 3.729,5.073 3.865,5.281 0.135,0.208 10 false D 5.802,5.073 5.938,5.281 0.135,0.208 10 false G 1.073,5.5 1.208,5.708 0.135,0.208 10 false 1 1.104,6.135 1.24,6.344 0.135,0.208 10 false 2 3.042,6.375 3.229,6.531 0.188,0.156 10 false *f 3.719,6.375 3.958,6.542 0.24,0.167 10 false *f 5.083,6.375 5.292,6.573 0.208,0.198 10 false *f 5.094,5.75 5.292,5.917 0.198,0.167 10 false *f 4.385,5.75 4.604,5.917 0.219,0.167 10 false *e 2.333,6.375 2.542,6.542 0.208,0.167 10 false *e 1.625,6.375 1.854,6.552 0.229,0.177 10 false *d 3.719,5.75 3.927,5.938 0.208,0.188 10 false *d 3.01,5.75 3.208,5.938 0.198,0.188 10 false *c 1.625,5.75 1.844,5.948 0.219,0.198 10 false *c 2.333,5.75 2.521,5.906 0.188,0.156 10 false *c 5.802,6.365 6.021,6.563 0.219,0.198 10 false *c 5.76,5.76 5.969,5.948 0.208,0.188 10 false *c 0.177,1.563 2.198,1.75 2.021,0.188 10 false -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 false -0°15' to 0° (-0.25° to 0°) 0.208,2.51 2.156,2.729 1.948,0.219 10 false -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 false -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 false -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 false -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 false 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 false 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 false 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 false 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 false 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 false 1°15' to 1°30' (1.25° to 1.5°) 2.542,1.406 2.76,1.604 0.219,0.198 10 false *c 3.219,0.792 3.448,0.969 0.229,0.177 10 false *c 3.917,0.792 4.135,1.01 0.219,0.219 10 false *c 4.604,0.792 4.823,1.01 0.219,0.219 10 false *c 5.979,3 6.24,3.24 0.26,0.24 10 false F 1.156,0.625 1.333,0.792 0.177,0.167 10 false *a 0.625,1.115 0.802,1.281 0.177,0.167 10 false *b 0.875,4.792 1.198,5.021 0.323,0.229 12 false *B 0.063,0.135 0.333,0.333 0.271,0.198 12 false *A
*A Table (1) (To move the axle hub toward the positive side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c 90105-17012 *b 90105-17013
*e 90105-17014 *f 90105-17015



ii.

Table (2) (To move the axle hub toward the negative side)

C212218C08
2.052,0.531 2.188,0.74 0.135,0.208 10 1 2.052,1.146 2.188,1.354 0.135,0.208 10 2 1.635,5.115 1.771,5.323 0.135,0.208 10 A 5.094,5.115 5.229,5.323 0.135,0.208 10 F 3.052,5.115 3.188,5.323 0.135,0.208 10 C 4.406,5.115 4.542,5.323 0.135,0.208 10 E 2.344,5.115 2.479,5.323 0.135,0.208 10 B 3.729,5.115 3.865,5.323 0.135,0.208 10 D 5.802,5.115 5.938,5.323 0.135,0.208 10 G 1.073,5.5 1.208,5.708 0.135,0.208 10 1 1.104,6.135 1.24,6.344 0.135,0.208 10 2 0.177,1.594 2.198,1.781 2.021,0.188 10 -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.792 1.969,2.979 1.563,0.188 10 -0°15' to 0° (-0.25° to 0°) 0.208,2.552 2.156,2.771 1.948,0.219 10 -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.313 2.156,2.51 1.948,0.198 10 -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.063 2.104,2.24 1.833,0.177 10 -1°00' to -0°45' (-1° to -0.75°) 0.26,1.844 2.094,2.052 1.833,0.208 10 -1°15' to -1°00' (-1.25° to -1°) 0.354,3.969 2.01,4.146 1.656,0.177 10 1°00' to 1°15' (1° to 1.25°) 0.354,3.74 2,3.938 1.646,0.198 10 0°45' to 1°00' (0.75° to 1°) 0.302,3.5 2.073,3.677 1.771,0.177 10 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.271 2.073,3.448 1.771,0.177 10 0°15' to 0°30' (0.25° to 0.5°) 0.448,3.031 1.917,3.229 1.469,0.198 10 0° to 0°15' (0° to 0.25°) 0.302,4.219 2.073,4.396 1.771,0.177 10 1°15' to 1°30' (1.25° to 1.5°) 1.156,0.625 1.333,0.792 0.177,0.167 10 *a 0.625,1.115 0.802,1.281 0.177,0.167 10 *b 0.875,4.792 1.167,5 0.292,0.208 12 *B 0.063,0.135 0.333,0.333 0.271,0.198 12 *A 5.292,2.792 5.427,3 0.135,0.208 10 E 5.292,3.74 5.427,3.948 0.135,0.208 10 G 5.292,2.552 5.427,2.76 0.135,0.208 10 F 5.292,3.5 5.427,3.708 0.135,0.208 10 A 5.292,3.031 5.427,3.24 0.135,0.208 10 C 5.292,3.271 5.427,3.479 0.135,0.208 10 B 2.542,2.792 2.677,3 0.135,0.208 10 A 2.542,1.594 2.677,1.802 0.135,0.208 10 F 2.542,2.313 2.677,2.521 0.135,0.208 10 C 2.542,1.844 2.677,2.052 0.135,0.208 10 E 2.542,2.552 2.677,2.76 0.135,0.208 10 B 2.542,2.063 2.677,2.271 0.135,0.208 10 D 3.229,2.792 3.365,3 0.135,0.208 10 B 3.229,3.031 3.365,3.24 0.135,0.208 10 G 3.229,2.552 3.365,2.76 0.135,0.208 10 C 3.229,2.063 3.365,2.271 0.135,0.208 10 E 3.229,2.313 3.365,2.521 0.135,0.208 10 D 3.229,1.844 3.375,2.052 0.146,0.208 10 F 3.927,2.792 4.063,3 0.135,0.208 10 C 3.927,3.271 4.063,3.479 0.135,0.208 10 G 3.927,3.031 4.063,3.24 0.135,0.208 10 A 3.927,2.063 4.063,2.271 0.135,0.208 10 F 3.927,2.313 4.063,2.521 0.135,0.208 10 E 3.927,2.552 4.063,2.76 0.135,0.208 10 D 4.604,2.792 4.74,3 0.135,0.208 10 D 4.604,3.5 4.74,3.708 0.135,0.208 10 G 4.604,3.271 4.74,3.479 0.135,0.208 10 A 4.604,3.031 4.74,3.24 0.135,0.208 10 B 4.604,2.552 4.74,2.76 0.135,0.208 10 E 4.604,2.313 4.74,2.521 0.135,0.208 10 F 5.99,3.969 6.125,4.177 0.135,0.208 10 G 5.99,3.74 6.125,3.948 0.135,0.208 10 A 5.99,3.271 6.125,3.479 0.135,0.208 10 C 5.99,3.5 6.125,3.708 0.135,0.208 10 B 5.99,3.031 6.125,3.24 0.135,0.208 10 D 5.99,2.792 6.125,3 0.135,0.208 10 F 6.688,4.219 6.823,4.427 0.135,0.208 10 G 6.688,3.969 6.823,4.177 0.135,0.208 10 A 6.688,3.5 6.823,3.708 0.135,0.208 10 C 6.688,3.031 6.823,3.24 0.135,0.208 10 E 6.688,3.74 6.823,3.948 0.135,0.208 10 B 6.688,3.271 6.823,3.479 0.135,0.208 10 D 2.531,0.781 2.708,0.948 0.177,0.167 10 *c 3.219,1.375 3.406,1.552 0.188,0.177 10 *d 5.969,0.781 6.115,0.938 0.146,0.156 10 *e 5.26,0.781 5.458,0.969 0.198,0.188 10 *d 4.604,1.375 4.781,1.552 0.177,0.177 10 *f 3.917,1.375 4.094,1.552 0.177,0.177 10 *e 5.979,1.375 6.188,1.531 0.208,0.156 10 *f 5.271,1.375 5.469,1.552 0.198,0.177 10 *f 6.656,1.375 6.833,1.531 0.177,0.156 10 *f 6.646,0.781 6.813,0.948 0.167,0.167 10 *f 2.531,1.375 2.708,1.552 0.177,0.177 10 *c 3.219,0.781 3.396,0.938 0.177,0.156 10 *c 3.917,0.792 4.104,0.979 0.188,0.188 10 *c 4.594,0.781 4.771,0.948 0.177,0.167 10 *c 4.406,6.375 4.552,6.531 0.146,0.156 10 *f 3.052,6.375 3.24,6.531 0.188,0.156 10 *f 3.729,6.375 3.969,6.542 0.24,0.167 10 *f 5.094,6.375 5.302,6.573 0.208,0.198 10 *f 5.094,5.75 5.281,5.906 0.188,0.156 10 *f 4.406,5.75 4.604,5.906 0.198,0.156 10 *e 2.344,6.375 2.552,6.542 0.208,0.167 10 *e 1.635,6.375 1.781,6.531 0.146,0.156 10 *d 3.719,5.75 3.906,5.938 0.188,0.188 10 *d 3.042,5.75 3.24,5.938 0.198,0.188 10 *c 1.635,5.75 1.813,5.938 0.177,0.188 10 *c 2.344,5.75 2.521,5.906 0.177,0.156 10 *c 5.802,6.375 5.99,6.542 0.188,0.167 10 *c 5.802,5.75 6.01,5.938 0.208,0.188 10 *c
*A Table (2) (To move the axle hub toward the negative side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c 90105-17012 *d 90105-17013
*e 90105-17014 *f 90105-17015




i.

If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step (A), replace the existing bolts with the selected bolts.

HINT:

Replace one bolt at a time when replacing both bolts.



Hide 5.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


d.
C188968C13
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.76,1.125 0.938,1.292 0.177,0.167 10 false *a 2.448,1.688 2.625,1.844 0.177,0.156 10 false *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.



f.
C188969C11
0.647,1.275 0.647,1.636 false 1.912,0.543 2.051,0.704 0.14,0.16 10 C 3.071,0.55 3.21,0.71 0.14,0.16 10 D 2.498,0.717 2.638,0.877 0.14,0.16 10 A 2.509,1.537 2.649,1.698 0.14,0.16 10 B 0.563,1.655 0.735,1.815 0.172,0.16 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle):
Specified Condition
C + D: 0.02° +/- 0.17° (0°01' +/- 0°10')
B - A: 0.3 +/- 2.0 mm (0.0118 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rack ends.


Hide 6.ADJUST TOE-IN

a.
C239071C06
3.021,0.906 3.229,1.125 0.208,0.219 10 true *a
*a Thread Length


Make sure that the thread length of the right and left rack ends are approximately the same.

Standard Difference:

1.5 mm (0.0591 in.) or less



b.

Remove the steering rack boot clips.


c.
C239070

Loosen the tie rod end lock nuts.


d.

Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.

i.

If the toe-in measurement is greater than the specified range (too much toe-out), extend the shorter rack end so that the length difference is within the specified range.


ii.

If the toe-in measurement is less than the specified range (too much toe-in), shorten the longer rack end so that the length difference is within the specified range.


iii.

Measure the toe-in.



e.
C317577C08
1.625,0.51 1.781,0.708 0.156,0.198 10 false A 1.667,1.365 1.823,1.563 0.156,0.198 10 false B 1.031,0.323 1.188,0.521 0.156,0.198 10 false C 2.208,0.344 2.365,0.542 0.156,0.198 10 false D
V100135

Front of the Vehicle


Turn the right and left rack ends by an equal amount to adjust the toe-in.

Toe-in (Unloaded Vehicle):
Specified Condition
C + D: 0.02° +/- 0.17° (0°01' +/- 0°10')
B - A: 0.3 +/- 2.0 mm (0.0118 +/- 0.0787 in.)


HINT:

Perform adjustments so that the value is as close as possible to the median of the specified range.



f.

Make sure that the thread lengths of the right and left rack ends are the same.


g.

Tighten the tie rod end lock nuts.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)


h.

Place the steering rack boots on the seats and install the steering rack boot clips.

HINT:

Make sure that the steering rack boots are not twisted.



Hide 7.INSPECT WHEEL ANGLE

a.
C132439C11
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Turning Angle (Unloaded Vehicle):
Model Inside Wheel Outside Wheel Reference
ASV50R-DETDKQ 38.61° +/- 2° (38°37' +/- 2°)
38.88° +/- 2° (38°53' +/- 2°)*1
37.16° +/- 2° (37°10' +/- 2°)*4
33.76° (33°46')
33.93° (33°56')*1
32.79° (32°47')*4
ASV50R-DETNKQ
ASV50R-DETVKQ 38.53° +/- 2° (38°32' +/- 2°)*3
37.16° +/- 2° (37°10' +/- 2°)*4
33.71° (33°43')*3
32.79° (32°47')*4
ASV50L-DETDKV 38.63° +/- 2° (38°38' +/- 2°)
38.94° +/- 2° (38°56' +/- 2°)*2
33.77° (33°46')
33.96° (33°58')*2
ASV50L-DETNKV


*1 for Papua New Guinea and Fiji

*2 for Iran and Yemen

*3 for 17 inch Wheel

*4 for 18 inch Wheel

If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.



Hide 86468 8.ADJUST LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)