The main body ECU (multiplex network body ECU) controls the rear fog lights via the engine room junction block assembly.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check the operation of the taillights.
Taillights operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Check that the relay operates.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Fog Light Relay | Rear fog light relay | ON/OFF | Make sure the light control switch is in the tail position |
| Tester Display |
|---|
| Rear Fog Light Relay |
Rear fog light relay operates. (Rear fog lights come on.)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using a voltmeter, check the signal reading of the engine room junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION
Output signal reading is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the engine room junction block assembly from the engine room relay block and junction block assembly.
| *a | Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (BATT) - Body ground | Always | 11 to 14 V |
| B-1 (ALT) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1F-3 (GND1) - Body ground | Always | Below 1 Ω |
| 1G-4 (GND2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1G-2 (TAIL) - 3D-9 | Always | Below 1 Ω |
| 1F-10 (RFGS) - 3D-35 | Always | Below 1 Ω |
| 1G-2 (TAIL) or 3D-9 - Body ground | Always | 10 kΩ or higher |
| 1F-10 (RFGS) or 3D-35 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-27 (RFGO) - 3D-35 | Always | Below 1 Ω |
| MB-27 (RFGO) or 3D-35 - Body ground | Always | 10 kΩ or higher |
Connect a positive (+) lead from the battery to terminal 3E-1.
Connect a negative (-) lead from the battery to terminal MB-14.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-9 - Battery negative | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 1F engine room junction block assembly connector.
Disconnect the T23 rear light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1F-12 (RFOG) - T23-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T23-2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the engine room junction block assembly with a new or a known good one.
Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL
Check that the rear fog lights operate normally.
The rear fog lights operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG