Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.05
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0233  Lost Communication with Blind Spot Monitor Master Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0233 Lost Communication with Blind Spot Monitor Master Module No communication from the blind spot monitor sensor RH continues.
·

Blind spot monitor sensor RH branch line or connector

·

Power source circuit of blind spot monitor sensor RH

·

Blind spot monitor sensor RH ground circuit

·

Blind spot monitor sensor RH


The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.

HINT:

This diagnosis procedure is for when DTC U0233 is output by the network gateway ECU (GTS display: Gateway).


WIRING DIAGRAM

C320694E03
2.708,2.292 2.708,1.552 2.708,1.552 2.917,1.552 false 5.49,2.292 5.49,1.979 5.49,1.979 5.313,1.979 false 1.604,2.292 1.604,1.094 1.604,1.094 1.813,1.094 false 0.125,0.083 5.719,0.708 5.594,0.625 12 false Sub Bus 2 (w/ Parking Assist Monitor System and Blind Spot Monitor System without Pre-crash Safety System and Lane Departure Alert System): 1.438,6.031 3.292,6.344 1.854,0.313 10 false : CAN Main Bus Line (CANH) 1.438,6.438 3.292,6.75 1.854,0.313 10 false : CAN Main Bus Line (CANL) 4.417,6.031 6.271,6.344 1.854,0.313 10 false : CAN Branch Line (CANH) 4.417,6.438 6.271,6.75 1.854,0.313 10 false : CAN Branch Line (CANL) 3.031,5.094 4.927,5.375 1.896,0.281 10 false Blind Spot Monitor Sensor RH 2.719,5.094 3.042,5.458 0.323,0.365 10 false O32 3.208,4.646 3.604,4.948 0.396,0.302 10 false BRB 2.146,4.802 3.177,5.052 1.031,0.25 10 false ECU-IG1 NO. 3 3.042,4.531 3.365,4.896 0.323,0.365 10 false 5 4.156,4.635 4.635,4.938 0.479,0.302 10 false BRGD 4.635,4.521 4.958,4.885 0.323,0.365 10 false 10 3.552,4.094 3.875,4.458 0.323,0.365 10 false 2 4.156,4.094 4.479,4.458 0.323,0.365 10 false 7 3.51,4.302 3.938,4.604 0.427,0.302 10 false CA1P 3.896,4.302 4.323,4.604 0.427,0.302 10 false CA1N 6.354,3.219 6.792,3.521 0.438,0.302 10 false 120 Ω 0.521,3.219 0.958,3.521 0.438,0.302 10 false 120 Ω 0.104,3.813 1.708,4.125 1.604,0.313 10 false Network Gateway ECU 1.906,1.01 3.948,1.333 2.042,0.323 10 false CAN No. 9 Junction Connector 3.01,1.479 5.052,1.802 2.042,0.323 10 false CAN No. 5 Junction Connector 3.375,1.896 5.417,2.219 2.042,0.323 10 false CAN No. 6 Junction Connector 5.521,4.99 6.552,5.24 1.031,0.25 10 false Trouble Area 5.823,3.833 7.052,4.271 1.229,0.438 10 false CAN No. 7 Junction Connector

C320676E03
2.396,2.292 2.396,1.979 2.396,1.979 2.729,1.979 false 1.688,2.292 1.688,1.677 1.688,1.677 1.896,1.677 false 5.115,2.292 5.115,1.427 5.115,1.427 4.875,1.427 false 5.604,2.292 5.604,1.094 5.604,1.094 5.365,1.094 false 0.125,0.094 5.76,0.604 5.635,0.51 12 false Sub Bus 2 (w/ Parking Assist Monitor System, Blind Spot Monitor System and Lane Departure Alert System): 0.542,3.229 1,3.458 0.458,0.229 10 false 120 Ω 6.323,3.229 6.781,3.458 0.458,0.229 10 false 120 Ω 0.042,3.823 1.646,4.188 1.604,0.365 10 false Network Gateway ECU 2.854,1.896 4.917,2.323 2.063,0.427 10 false CAN No. 9 Junction Connector 1.979,1.604 4.042,2.031 2.063,0.427 10 false CAN No. 8 Junction Connector 2.906,1.344 4.969,1.771 2.063,0.427 10 false CAN No. 5 Junction Connector 3.396,1 5.458,1.427 2.063,0.427 10 false CAN No. 6 Junction Connector 3.021,5.115 4.927,5.385 1.906,0.271 10 false Blind Spot Monitor Sensor RH 2.146,4.802 3.177,5.052 1.031,0.25 10 false ECU-IG1 NO. 3 2.708,5.125 3.167,5.354 0.458,0.229 10 false O32 3.24,4.646 3.698,4.875 0.458,0.229 10 false BRB 3.51,4.313 3.969,4.542 0.458,0.229 10 false CA1P 3.927,4.313 4.385,4.542 0.458,0.229 10 false CA1N 4.156,4.625 4.615,4.854 0.458,0.229 10 false BRGD 3.052,4.542 3.24,4.781 0.188,0.24 10 false 5 3.573,4.104 3.76,4.344 0.188,0.24 10 false 2 4.135,4.104 4.323,4.344 0.188,0.24 10 false 7 4.635,4.531 4.875,4.75 0.24,0.219 10 false 10 5.469,4.781 6.5,5.031 1.031,0.25 10 false Trouble Area 1.448,6.021 3.563,6.313 2.115,0.292 10 false : CAN Main Bus Line (CANH) 1.438,6.438 3.552,6.729 2.115,0.292 10 false : CAN Main Bus Line (CANL) 4.438,6.438 6.552,6.729 2.115,0.292 10 false : CAN Branch Line (CANL) 4.427,6.021 6.542,6.313 2.115,0.292 10 false : CAN Branch Line (CANH) 5.813,3.833 7.052,4.365 1.24,0.531 10 false CAN No. 7 Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 22 seconds, and then drive the vehicle at a speed of 5 km/h (3 mph) or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.


Body Electrical > Gateway > Trouble Codes
50001 150
HINT:

If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.


Result:
Result Proceed to
DTC U1002 is not output from the network gateway ECU (GTS display: Gateway) A
DTC U1002 is output from the network gateway ECU (GTS display: Gateway) B



A

2.CHECK FOR OPEN IN SUB BUS 2 LINES (BLIND SPOT MONITOR SENSOR RH BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 2 LINES (BLIND SPOT MONITOR SENSOR RH BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the O32 blind spot monitor sensor RH connector.


c.
C250065C27
0.438,1.51 0.885,1.781 0.448,0.271 1.625,1.552 1.625,0.51 1.625,0.51 1.896,0.51 true 1.625,1.823 1.625,2.542 1.625,2.542 1.896,2.542 true 0.083,0.042 0.469,0.198 0.385,0.156 10 false *a 1.969,0.438 2.365,0.594 0.396,0.156 10 false CA1P 1.979,2.448 2.375,2.604 0.396,0.156 10 false CA1N 0.5,1.563 0.979,1.917 0.479,0.354 10 false O32
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O32-2 (CA1P) - O32-7 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C250065C28
0.438,1.51 0.885,1.781 0.448,0.271 2.073,1.802 2.073,2.521 2.073,2.521 2.344,2.521 true 0.083,0.042 0.469,0.198 0.385,0.156 10 false *a 2.375,2.438 2.917,2.635 0.542,0.198 10 false BRGD 0.521,1.563 1.25,2.021 0.729,0.458 10 false O32
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O32-10 (BRGD) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C250065C29
0.438,1.51 0.885,1.781 0.448,0.271 2.052,1.552 2.052,0.552 2.052,0.552 2.302,0.552 true 0.083,0.042 0.469,0.198 0.385,0.156 10 false *a 2.406,0.479 2.802,0.635 0.396,0.156 10 false BRB 0.49,1.563 1.042,1.823 0.552,0.26 10 false O32
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O32-5 (BRB) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)